BRESSER 7004310 Crystalvision Weather Station Instruction Manual

: June 9, 2024
: BRESSER

Table of Contents

BRESSER 7004310 Crystalvision Weather Station
ABOUT THIS INSTRUCTION
SCOPE OF DELIVERY
PRODUCT OVERVIEW
OUTDOOR SENSOR
LCD DISPLAY
GETTING STARTED
CLOCK
ALARM
OPERATION
LANGUAGE
SPECIFICATIONS
OUTDOOR SENSOR
WARRANTY & SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRESSER 7004310 Crystalvision Weather Station

BRESSER-7004310-Crystalvision-Weather-Station-product

ABOUT THIS INSTRUCTION

These operating instructions are to be considered a component of the device.
Please read the safety instructions and the operating instructions carefully before use.
Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product. The device is intended only for indoor use.

GENERAL WARNINGS

Risk of electric shock — This device contains electronic components. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.
Choking hazard — Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the bateries correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery
acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.
Risk of fire/explosion — Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire, or an explosion.
- Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
- Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. The batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Weather station, Outdoor sensor, Operating instruc-tions, 5V/1A USB adapter, 5x AAA batteries.

BEFORE YOU BEGIN

We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recommend using lithium batteries.
Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power require-ments.)
Insert batteries before first use, matching the polarity in the battery compartment. 3x AAA Batteries are required for the Weather station and 2x AAA Batteries are required for the Outdoor sensor.

PRODUCT OVERVIEW

$BRESSER-7004310-Crystalvision-Weather-Station-fig- $4$$

Press [ MODE ] to view time and alarm, press and hold to enter time and date setting.
Press [ ALARM ] to turn on/off alarm time, press and hold to enter alarm setting.
In setting mode, press [ ] to increase one unit, press and hold to increase rapidly. In non-setting mode, press and hold to turn on/off RCC.
In setting mode, press [ ] to decrease one unit, press and hold to decrease rapidly. In other modes, press to turn on/off the Upper and lower temperature and humidity alarm. Hold to enter the Upper and lower temperature and humidity alarm setting.
Press [ ] to activate the backlight for 10 seconds or to activate the snooze function to delay the alarm by 5 minutes. When connected to the adapter, the backlight can be set to 4 levels of brightness.
Press [ MAX/MIN ] to view temperature MAX/ MIN, press and hold to clear max/min memory.
Press [ CHANNEL ] to view 3 channel outdoor sensor temperature and humidity, press and hold to initialize outdoor sensor channel.
Wall Mount
Battery compartment
Table stand
USB Power In

OUTDOOR SENSOR

$BRESSER-7004310-Crystalvision-Weather-Station-fig- $6$$

Outdoor temperature & humidity LCD display
Battery compartment
TX (Transmit temperature and humidity signal during the sensor initiation search)
Channel switch
C/F switch

BUTTON MODE| MODE| ALARM| | | MAX/MIN| | CHANNEL
---|---|---|---|---|---|---|---

Standard mode

|

PRESS

|

Toggle between time and alarm display

|

Turn Alarm on/off

|

Turn on/off temperature and humidity alarm

| Toggle the display among current, maximum

and minimum recording of temperature and humidity

| 1. Adjust backlight brightness with

adapter

2. Turn on backlight for 10 seconds with

batteries

3. SNOOZE 5 minutes when alarm

is ringing

|

Toggle between outdoor sensor channel 1-3

HOLD

| Enter into time setting| Enter into alarm setting|

Turn RCC on/off

| Enter

temperature and humidity alarm setting

| Clear the max/ min memory records.|

| Initiate outdoor sensor search

Time OR Temperature and humidity setting mode

|

PRESS

|

Confirm

setting

|

Increase

|

Decrease

|

| 1. Adjust backlight brightness with

adapter

2. Turn on backlight for 10 seconds with

batteries

|

Alarm setting mode

|

PRESS

|

Confirm

setting

|

Increase

|

Decrease

|

| 1. Adjust backlight brightness with

adapter

2. Turn on backlight for 10 seconds with

batteries

|

LCD DISPLAY

Outdoor Temperature & humidity
Weather forecast
Time
Indoor Temperature & humidity
Moon phase
Date & Week $BRESSER-7004310-Crystalvision-Weather-Station-fig- $8$$

GETTING STARTED

INSERT BATTERIES

Remove the battery door from the back.
Insert 3x AAA (LR03)/1.5V batteries. Please ensure the polarities (+/-) of the batteries match upon installation.
Reattach the battery door.

NOTE : Replace batteries when [ ] displays, or when the display is dim

OUTDOOR SENSOR

The main unit can receive data from up to 3 outdoor sensors. 1 Sensor is included with delivery

Remove the battery door from the back.
Insert 2x AAA (LR03)/1.5V batteries. Please ensure the polarities (+/-) of the batteries match upon installation.
Select a channel, then press TX.
Reattach the battery door.
Place the sensor within 30 m (98 ft) of the main unit using the table stand or wall mount.

TO SEARCH FOR A SENSOR:

The main unit will automatically search for a new sensor after the batteries are installed. To manually initiate a outdoor sensor search, press and hold [ CHANNEL ].

NOTE : The transmission range may vary depending on many factors. You may need to experiment with various locations to get the best results

CLOCK

CLOCK RECEPTION

When you insert or replace the batteries, RCC (atomic) reception is initiated. To manually start RCC (atomic) reception press and hold the [ ] button.
The receiving process duration is 7 minutes.
During receiving process, the RCC (atomic) signal symbol shows: [ ] and the backlight is at a low level.
If the RCC (atomic) receiving process is successful, a completed RCC (atomic) symbol [ ] will be shown in the display and the date and time will be set automatically. If it fails within 7 minutes, RCC (atomic) setting will quit automatically. If that happens, press and hold the [ ] button to re-initiate RCC (atomic) receiving
NOTE : The interference from the power adapter will affect RCC (atomic) reception. It is recommended to place the power adapter at least 1m away from the console to get the best RCC (atomic) reception

SET THE CLOCK MANUALLY

Press and hold [ MODE ] button to enter into time and date setting.
The setting parameter will flash.
Press [ ] button once, the figure will increase 1 unit. Press and hold the [ ] button, the figures will increase rapidly.
Press [ ] button once, the figure will decrease 1 unit. Press and hold the [ ] button, the figures will decrease rapidly.
Press [ MODE ] button to confirm setting and enter to next parameter.
Sequence of setting:
EU/AUS Version
12/24h format Hour Minute Year Month Day Language Time zone Key tone on / off Temperature unit (°C/°F) Exit
If there is no action in 20 seconds, the setting will be saved and you will exit the setting mode

ALARM

SETTING/ADJUSTING ALARM TIME

Press and hold [ ALARM ] to enter alarm setting mode.
The setting parameter will flash.
Press [ ] or [ ] button to set the desired data.
Press [ ALARM ] button to confirm setting and exit.
Alarm will turn on automatically when alarm setting is finished.

TURN ON/OFF ALARM

Press the [ ALARM ] button to turn on/off the alarm.

OPERATION

At the set alarm time, alarm signal rings.
During the alarm, press the [ ] button to delay the alarm by 5 minutes.
If you do not press any button to stop the alarm, it will automatically turn off after 2 minutes.
To stop the alarm, press [ ALARM ] or any other button, except for SNOOZE.
The alarm will start again at the next alarm time, unless you switch off the alarm function by pressing the [ ALARM ] button until the alarm is set to off.

WEATHER FORECAST

This device forecasts the next 12-24 hours of weather within a 30-50 km (19-31 mile) radius with a 75% accuracy $BRESSER-7004310-Crystalvision-Weather- Station-fig- $12$$

MOON PHASE

The phase of the moon depends on the current date. It is automatically calculated and the following symbols are displayed

LANGUAGE

Press and hold [ MODE ] button to enter time setting, press [ MODE ] to enter language setting.
Sequence of setting weekday language:
EU/AUS Version
German (GER) English (ENG) Italian (ITA) French (FRE) Netherlands (NET) Spain (ESP) Danish (DAN) Symbol| GER| ENG| ITA| FRE| NET| ESP| DAN
---|---|---|---|---|---|---|---
Monday| MON| MON| LUN| LUN| MAA| LUN| MAN
Tuesday| DIE| TUE| MAR| MAR| DIN| MAR| TIR
Wednesday| MIT| WED| MER| MER| WOE| MIE| ONS
Thursday| DON| THU| GIO| JEU| DON| JUE| TOR
Friday| FRE| FRI| VEN| VEN| VRI| VIE| FRE
Saturday| SAM| SAT| SAB| SAM| ZAT| SAB| LOR
Sunday| SON| SUN| DOM| DIM| ZON| DOM| SON

TEMPERATURE AND HUMIDITY

The indoor temperature is displayed in the center on the left of the screen. To receive outdoor temperature you can connect up to 3 outdoor sensors to the main unit.

Press the [ CHANNEL ] button to toggle between Channel 1-3. MAX/MIN MEMORY
To toggle between current, minimum and maximum records for the selected sensor press [ MAX/MIN ] repeatedly. To clear records, press and hold [ MAX/MIN ] in max/min interface.
NOTE : When the indoor temperature is lower than-5 °C (23.0 °F), the screen displays LL.L. When the temperature is higher than 50 °C (122.0 °F), the screen displays HH.H.

TEMPERATURE AND HUMIDITY ALARM SETTING

Press and Hold [ ] enter to set temperature and Humidity alarm.
The setting parameter will flash.
Press [ ] or [ ] button to set the desired data.
Press [ MODE ] button to confirm setting and enter to next parameter.
Sequence of setting: Indoor upper temperature limit Indoor lower temperature limit Indoor upper humidity limit Indoor lower humidity limit outdoor upper temperature limit outdoor lower temperature limit outdoor upper humidity limit outdoor lower humidity limit

TEMPERATURE AND HUMIDITY ALARM OPERATION

Press [ ] to on/off temperature and Humidity alarm.
When the measured temperature or humidity is greater than the set upper limit or lower than the set lower limit, the station will give an alarm

ICE ALERT

If the channel 1 sensor falls between -2°C to 3°C (28°F to 37°F), the ice alert indicator [ ] will display, and will disappear once the temperature is out of this range.

BACKLIGHT

Press [ ] to activate backlight for 10 seconds.
When connected to the adapter, the backlight can be set to 4 levels of brightness

SPECIFICATIONS

MAIN UNIT:
- Dimensions
- 120 x 29 x 183 mm (L x W x H)
- Weight
- 268 g (Exclude batteries)
- Power:
- 3x AAA (LR03) 1.5V batteries
- 5V/1A USB Adapter
TEMPERATURE:
- Indoor temperature display range : -14°C to +50°C (14°F to 122°F)
- Outdoor temperature display range : -20°C to +60°C (-4°F to 140°F)
HUMIDITY :
- Indoor/outdoor humidity range : 20% – 95% RH

OUTDOOR SENSOR

Dimensions: 60 x 20 x 60 mm (L x W x H)
Weight: 45 g (Exclude batteries)
Transmission range : 30 m (98 ft)
Temperature range : -20°C to 60°C (-4°F to 140°F)
Signal frequency: 433 MHz
Maximum transmission power : under 10mW
Power: 2x AAA (LR03) 1.5V batteries

EC DECLARATION OF CONFORMITY

Hereby, Bresser GmbH declares that the equipment type with part number: 7004310 is in compliance with Directive: 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.bresser.de/download/7004310/CE/7004310_CE.pdf

UKCA DECLARATION OF CONFORMITY

Bresser UK Ltd. has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the UKCA declaration ofconformity is available at the following internet address: www.bresser.de/download/7004310/UKCA/7004310_UKCA.pdf
Bresser UK Ltd. Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain
Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTES ON CLEANING

Remove the batteries before cleaning.
Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
Protect the device from dust and moisture

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner

In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in the normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market.
Disposal in domestic waste violates the Battery
Directive. Batteries that contain toxins are marked with a sign and a chemical symbol.

battery contains cadmium
battery contains mercury
battery contains lead

WARRANTY & SERVICE

EU Version
The regular guarantee period is 5 years and begins on the day of purchase. You can consult the full guarantee terms and details of our services at www.bresser.de/warranty_terms.
Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions.
Alternatively you can also send an email to manuals@bresser.de or leave a message on +49 (0) 28 72 – 80 74-220*. Please always state your name, precise address, a valid phone number and email address, as well as the article number and name.
Number charged at local rates in Germany (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

MANUAL DOWNLOAD:

http://www.bresser.de/P7004310

SERVICE AND WARRANTY $BRESSER-7004310-Crystalvision-Weather-Station-fig- $15$$

http://www.bresser.de/warranty_terms

Bresser GmbH Gutenbergstraße 2 46414 Rhede · Germany www.bresser.de
Bresser UK Ltd. Suite 3G, Eden House Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain rrtümer und technische
Errors and technical changes reserved.
Manual_7004310__Funk-Wetterstation-ClimateTemp-NDV_de-en-it-fr-es- nl_BRESSER_v012022