KICHLER 82381 Anamaya 5-Light Chandelier Instruction Manual

KICHLER 82381 Anamaya 5-Light Chandelier

ATTACH YOUR RECEIPT HERE

• Serial Number
• Purchase Date

MODEL # 82381, 82384

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 800-554-6504, 8 a.m. – 4:30 p.m, EST, Monday – Friday. kichler.com/customer-care/contact-us

PACKAGE CONTENTS

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• CAUTION – RISK OF SHOCK –
  Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

• WARNING:

  • This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.

• Do not use bulbs with wattage greater than specified on this fixture.

• California Proposition 65

• WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to http://www.P65Warnings.ca.gov

CAUTION

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

• Estimated assembly time: 30 minutes to 1 hour
• Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses, pliers (2).

ASSEMBLY INSTRUCTIONS

1. Screw threaded rod (O) to fixture coupling (P). Secure by screwing one hex nut (D) tightly against fixture coupling. Slip rod cover (Q) and check ring (R) over threaded rod. Screw coupling (F) to threads that are protruding through the check ring.
   NOTE : The electrical cable will need to get pulled through the individual parts as they are installed on this and later steps

2. Screw 12 inch threaded pipe (G) into stem 2 coupling (F). Next, screw 6 inch threaded pipe (J) into 12 inch threaded pipe (G). Finally, screw fixture loop (M) into 6 inch threaded pipe (J).
   NOTE : The hanging height for this fixture is adjustable. Add or subtract threaded pipes to achieve the desired height.

3. Position threaded nipple (C) in mounting bracket (B) so that, when mounted:

4. The threaded nipple (C) will protrude a minimum of 1/4 inch beyond the raised center portion of the bracket (B).

5. The threaded nipple (C) height should be positioned so that 1/2 the exterior threads of the screw collar loop (I) will extend past the canopy (A), when it is mounted.
   NOTE : Canopy is only needed to determine the position of the threaded nipple and fixture loop. It will be installed later

6. Once the proper position of the threaded nipple(C) and mounting bracket (B) has been determined, secure with hex nuts (D) as follows:

7. Screw one hex nut (D) onto the threaded nipple (C) and tighten against the raised portion of the mounting bracket (B).

8. Screw another hex nut (D) onto the threaded nipple (C) and tighten against the flat portion of the mounting bracket (B)

9. Screw the remaining hex nut (D) onto threaded nipple (C) and tighten against the screw collar loop (I)

10. Connect mounting bracket (B) to the outlet box (not included) with short machine screws (BB).
    Hardware Used

11. Carefully pass screw collar ring (H) and canopy (A) over the screw collar loop (I). Using the open chain link (K), connect fixture loop (M) to screw collar loop (I). Close link using pliers. Then, pass electrical and ground wires through threaded nipple (C) into outlet box.

12. Wire connection guide:
    Ground wire:

13. For installation in the United States: Wrap ground wire from outlet box around ground screw on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).

14. For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with a wire connector (AA).
    Supply wires:

15. Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).

16. Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).
    Hardware Used

17. Pass canopy (A) over the screw collar loop (I). Attach screw collar ring (H) to screw collar loop (I) to secure canopy (A).

18. Pass glass shade (L) over socket (E) and secure it with socket ring (N).

19. Insert 60-watt max. E26 medium base bulb or LED equivalent (not included) into socket (E). Repeat for remaining sockets (E).

CARE AND MAINTENANCE

• Always be certain that electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish.
• All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher

TROUBLESHOOTING

2.    Worn or broken bulb.

| 1.  Check wiring.

2.    Replace bulb.

Distributed by:
Kichler Lighting LLC 30455 Solon Rd Solon, OH 44139 Printed in China

References

• Contact Kichler - Get in touch with us | Kichler Lighting
• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>