KICHLER Baile 2 Light Wall Sconce in Greige and Brushed Nickel Instruction Manual
- June 9, 2024
- KICHLER
Table of Contents
KICHLER Baile 2 Light Wall Sconce in Greige and Brushed Nickel
FIXTURE DIAGRAM
PARTS LIST
- [A] Mounting Strap
- [B] Outlet Box (Not Supplied)
- [C] Strap Mounting Screw (2)
- [D] Mounting Screw (2)
- [E] Canopy
- [F] Arc Retaining Knob (10)
- [G] Ring Retaining Screw (4)
- [H] Arc (5)
- [I] Arc Support Ring
- [J] Lock-up Knob (2)
- [K] Arc Mounting Studs (10)
CAUTIONS
Disconnect Power at the main circuit breaker panel or main fusebox before
starting and during the installation.
WARNING:
- This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.
CLEANING:
- Always be certain that electric current is turned off before cleaning.
- Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.
INSTALLATION INSTRUCTIONS
-
Find the appropriate threaded holes on mounting strap[A] that align with hole distance in canopy[E]. Thread mounting screws[D] into threaded holes starting from outlet box[B] side.
-
Attach mounting strap[A] to outlet box[B] using the strap mounting screws[C].
-
Grounding instructions: (See Illus. a or b).
-
On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
-
On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
-
Make wire connections. Reference chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
Note : When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)
- Push canopy to wall, carefully aligning the mounting screws protruding from the mounting strap with holes in canopy.
- Screw lock-up knobs[J] onto threads protruding through holes in canopy (2 places) to attach fixture to wall. Tighten to secure.
- Remove and set aside the pre-installed arc retaining knobs[F] from arc support ring[I], keeping the arc support ring intact and exposing the arc mounting studs[K].
- Slip an arc[H] onto the first two exposed arc mounting studs on the arc support ring as shown, then screw two arc retaining knobs from the previous step back onto the exposed arc mounting studs. Tighten to secure. Repeat for remaining arcs, ensuring all arcs are oriented in the same direction (all pointed ends of arcs facing one direction, and all blunt ends of arcs facing the opposite direction, once installed to arc support ring).
- With the blunt end of the arks oriented down toward the floor, align the through holes at the ends of the arc support ring with the holes on the sides of the canopy and screw in the ring retaining screws[G] to attach arc support ring to canopy. Tighten to secure.
- Insert recommended bulbs (not included).
warranty
For warranty information please visit: kichler.com/warranty
INSTRUCTIONS:
For Assembling and Installing Fixtures in Canada
We’re here to help866-558-5706 Hrs: M-F 9am to 5pm EST