niko 552-720X4 Wireless Battery-Powered Switch User Manual

: June 9, 2024
: niko

Table of Contents

niko 552-720X4 Wireless Battery-Powered Switch
Description
Dimensions
Zigbee® network
Installation
Stand-alone use
Connected use
Troubleshooting
LED behavior
Reset
Specifications
Support & contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

niko 552-720X4 Wireless Battery-Powered Switch

Description

This fourfold wireless battery-powered Zigbee® switch allows you to remotely control wireless Zigbee® devices. It can either be used in a Niko Home Control installation (max. fifty Zigbee® devices) or connected to a third-party Zigbee® system as a standard dimmer switch (ON/OFF/ dimming) via EZ-mode pairing. The switch also supports Touchlink or Find&Bind to pair with up to eight Zigbee® receivers (ON/OFF/dimmable actor) for stand-alone use or decentral networks. The wireless Zigbee® switch is battery-powered with a lifetime of at least five years, based on twenty short press actuation a day. The variant with a plastic baseplate (552-72004) is used for wall installation. Fixation is possible with double-sided adhesive tape (included) or screws (excluded). For flush-mounting box installation, use variant 552-72014 together with the metal baseplate (552-720X0) suitable for your region.

Dimensions

552-72004
552-72014

Zigbee® network

Install the fourfold wireless battery-powered Zigbee® switch within 10 m of a Zigbee® receiver. Battery-powered Zigbee® devices act as endpoints and do not support Zigbee® mesh networking. For more information on Zigbee® network principles and signal range, consult guide.niko.eu.

Installation

$niko-552-720X4-Wireless-Battery-Powered-Switch- $5$$

Battery replacement

Stand-alone use

The fourfold wireless battery-powered Zigbee® switch (522-720X4) can be used in stand-alone mode without a gateway. In this mode, each control button can be paired with Zigbee® receivers (ON/OFF/dimming). The fourfold switch can be paired with up to eight Zigbee® receivers in total, such as a smart Zigbee® 3.0 lamp. Pairing is done via Touchlink or Find&Bind.

Touchlink pairing
Reset all Zigbee® devices if they were previously connected to another Zigbee® network. See § Reset. For Find&Bind pairing consult guide.niko.eu

Connected use

Connected to a Niko Home Control installation
More advanced functionalities become available if you connect this device to your wireless smart hub (552-00001) or wireless bridge (550-00640) using the Niko Home Control programming software or Niko Home app. Consult guide.niko.eu for more information about the installation and the connected use.

How to connect the Niko device to the Niko Home Control network

Reset the Niko Zigbee® device if it is already connected to another network.
Follow the onboarding procedure in the Niko Home Control programming software or the Niko Home app to add new Niko Zigbee® devices.
Set the Niko Zigbee® device in EZ-mode by pressing the switch button 3 x within 6 seconds > see the image on ‘EZ-mode pairing’. The blue PROGRAM LED starts blinking for max. 90 seconds.
The Zigbee® device is successfully added to the Niko Home Control installation when the blue PROGRAM LED is ON for 4 seconds and then turns OFF again.

EZ-mode pairing

Connected to a third-party Zigbee® network
The fourfold wireless battery-powered Zigbee® switch can be connected to a third-party network via EZ-mode pairing. Refer to the third-party software or smartphone app to link a specific button of the battery-powered Zigbee® switch to an actor within the third-party network. You can also use Find&Bind pairing. Consult guide.niko.eu and the manufacturer’s manual for more information on using third-party Zigbee® devices in their network. Note that specific Niko Home Control functions will not be enabled when Niko Zigbee® devices are connected to a third-party Zigbee® gateway. See also the disclaimer at http://www.niko.eu/zigbee.

Online guide
Consult guide.niko.eu for more information about the installation, onboarding, the stand-alone/connected use and troubleshooting.

guide.niko.eu

Troubleshooting

Problem	Cause	Action

The connected switch cannot be found in the Niko Home app or programming software| The power supply of the wireless smart hub for Niko Home Control is OFF| Switch on the power supply of the wireless smart hub for Niko Home Control
The battery of the Zigbee® switch is drained| A battery low warning is displayed on the Niko Home Control Home app. A battery low indication (red- colored LED) will only be shown on the Zigbee® device after a long press on the PROGRAM button (see § Reset). Replace the coin cell battery (refer to § Battery replacement). Mind that the PRO-GRAM LED remains OFF when the battery voltage level is below the minimum threshold
The receiver never responds when I press a Zigbee ® **switch button in stand-alone use| The battery of the Zigbee® switch is drained
The Zigbee® switch is not correctly paired with the receiver| Reset the Zigbee® battery-pow- ered switch if it was paired to another Zigbee® network. Pair the switch to a stand-alone receiver, Niko Home Control, or a third- party Zigbee® network. See guide. niko.eu for more details
Another Zigbee® battery-powered switch is paired with the receiver
The Zigbee® battery-powered switch is mounted outside of the receiver’s radio coverage or is sometimes moved outside the range| Move the Niko Zigbee® switch closer to the receiver or use a range extender such as a 230 V powered Zigbee® 3.0 device in a Niko Home Control installation or third-party system
The radio path is obstructed, which attenuates the radio signal| Reposition the Zigbee® switch or use a range extender such as a 230 V powered Zigbee® 3.0 device in a Niko Home Control installation or third-party system
A jammer or a source of interference is blocking the telegrams from the Zigbee® battery-powered switch to the receiver| Reposition the Zigbee® switch or Zigbee® receiver. Remove the interfering device or use a range extender such as a 230 V powered Zigbee® 3.0 device in a Niko Home Control installation or third-party system
The Zigbee® battery-powered switch is defective| Replace the switch and pair the new Zigbee® battery-powered switch with the receiver. Both devices may have to be reset first
The receiver is defective| Replace the receiver and pair it with the new Zigbee® receiver
The receiver doesn’t always respond when I press the Niko Zigbee ® ****battery-pow- ered switch**| The receiver is located at the border of the radio coverage area| Install the switch closer to the receiver or use a range extender such as a 230 V powered Zigbee® 3.0 device in a Niko Home Control installation or third-party system
A jammer or a source of interference is blocking the telegrams from the Niko Zigbee® battery-powered switch to the receiver| Reposition the Zigbee® switch or receiver, remove the interfering device or use a range extender such as a 230 V powered Zigbee® 3.0 device in a Niko Home Control installation or third- party system

LED behavior

The feedback LED will only be visible when the battery-powered Zigbee® switch is dismantled from the baseplate and after a long press on the PROGRAM button. The PROGRAM LED is found at the back of the switch.

Reset

Specifications

Article number …………………………………………………………..552-721X4
Power supply ………………………………………………… 3 V battery, CR2450
Battery life span ………………………………… 5 years at 20 actuations/day
Protocol ………………………………………………………. Zigbee® 3.0, 2.4 GHz
Mounting method 552-72004 …………………………………..wall mounting
Mounting method 552-72014 ……… flush-mounting box in combination with metal baseplate 552-720X0
Flush-mounting box specifications.
- depth = min. 40 mm
- claw/screw fixing = 60 mm
- inner diameter box = 60 mm
- multiple boxes centre distance horizontal = 71 mm
- multiple boxes centre distance vertical = 71 mm
- multiple boxes centre distance vertical = 60 mm for BE and FR
Mounting height ……………………………………………………. 105 – 120 cm
Dimensions with Niko Original or Niko Pure faceplate (HxWxD) ………………………………………………………………… 83 x 83 x 15 mm
Dimensions with Niko Intense faceplate (HxWxD) ………………………………………………………………… 85 x 85 x 15 mm
Protection degree ………………………………………………………………..IP20
Maximum range (between switch and smart hub or wireless bridge) ………………………………………. 10 m (longer ranges possible with meshing capability of 230 V connected Zigbee® devices)
Maximum per installation
- max. 50 connected Zigbee® devices per
- Niko Home Control installation
- stand-alone: max. 8 Zigbee® receivers
- (ON/OFF/dimming) per switch
Operating frequency ………………………………………………………..2.4 GHz
Antenna ………………………………………………………….. integrated antenna
Maximum RF power …………………………………………………..8 dBm EIRP
Ambient temperature operation ………………………………..5 °C – 30 °C
Ambient temperature storage …………………………………..0 °C – 40 °C
Humidity ………………………… 0 – 95 % relative humidity, non-condensing
Weight 552-72004 ………………………………………………………. 23 g ±1 g
Weight 552-72014 ………………………………………………………. 17 g ±1 g
Marking …………………………………………………………………… CE, Zigbee®

Warnings regarding installation
The installation of products that will permanently be part of the electrical installation and which include dangerous voltages, should be carried out by a qualified installer and in accordance with the applicable regulations. This user manual must be presented to the user. It should be included in the electrical installation file and it should be passed on to any new owners. Additional copies are available on the Niko website or via Niko customer services.

CE marking
This product complies with all of the relevant European guidelines and regulations. For radio equipment, Niko LLC declares that the radio equipment in this manual conforms with the 2014/53/EU directive. The full text of the EU declaration of conformity is available at www.niko.eu under the product reference, if applicable.

Environment
This product and/or the batteries provided cannot be disposed of in the non-recyclable waste. Take your discarded product to a recognized collection point. Just like producers and importers, you too play an important role in the promotion of sorting, recycling and reuse of discarded electrical and electronic equipment. To finance the rubbish collection and waste treatment, the government levies recycling charges in certain cases (included in the price of this product).

Support & contact

nv Niko sa
Industriepark West 40
9100 Sint-Niklaas, Belgium

www.niko.eu
+32 3 778 90 80
support@niko.eu

Niko prepares its manuals with the greatest care and strives to make them as complete, correct and up-to-date as possible. Nevertheless, some deficiencies may subsist. Niko cannot be held responsible for this, other than within the legal limits. Please inform us of any deficiencies in the manuals by contacting Niko customer services at support@niko.eu.