AQUA-AMP AA01ACT Wireless Charger Instruction Manual
- June 17, 2024
- AQUA-AMP
Table of Contents
AQUA-AMP AA01ACT Wireless Charger
Important Information
The product must be installed according to the specified instructions. Failure to comply may result in personal injury, vessel/vehicle damage, and/or product failure. Installation by a trained electrician is recommended by Aqua Amp. Damage and/or injuries caused by improper installation are not covered by the warranty
WARNING :
Only a 12V DC or 24V DC battery/power supply should be used with this device.
Before installing, the power supply must be turned off.
Between the battery/power supply and the product, an appropriate fuse or
circuit breaker must be utilized.
Before turning on the electricity, double-check that all wiring is polarized
correctly. High voltages may be included in this product. Do not alter the
product in any way. This product is not intended for use in potentially
hazardous or flammable environments.
Do not install in a hazardous/flammable environment, such as engine rooms.
Make sure the space behind the mounting point is clear of wires, fuel, and any
other potentially hazardous things before drilling any holes.
Ensure that any holes cut do not considerably degrade the surface’s structure.
If the product must be installed outside, it must be installed safely above
the waterline and not in danger of being submerged.
A metallic surface prevents the product from charging.
CAUTION:
The item is designed to charge Qi compatible devices only.
The cable must be kept in place and not obstruct mechanical systems.
There are no user-serviceable components in this product. In no way attempt to
repair or modify the product.
The device’s high friction top surface does not guarantee that it will not
slip during strong acceleration and deceleration working situations.
A phone case thicker than 3mm may prevent the smartphone from charging.
The product may temporarily shut down if used in a hot environment or in
direct sunlight; this is a safety feature of the electronics.
The IP rating is only valid if the instructions are followed correctly. Avoid
mounting near heat-radiating appliances and in poorly ventilated spaces when
choosing a placement.
EMC INSTALLATION GUIDELINES:
To ensure that electromagnetic interference between equipment is minimized,
Aqua Amp devices comply with Electromagnetic Compatibility (EMC) requirements.
To keep electromagnetic interference to a bare minimum, proper installation is
essential.
WIRING
When extending the wire from your battery/power source to the product, make
sure there is a continuous supply of at least 10V. For any length of cable
extension, we recommend an 18AWG (0.82mm2) wire gauge.
This diagram shows how the product should be linked to a 12V or 24V DC battery
or power supply.
ENVIRONMENTAL PROTECTION:
Electrical trash should not be thrown out with household garbage. Please
recycle wherever possible. For recycling advice, contact your local government
or a merchant.
IMPORTANT
AquaAmp LLC disclaims all liability for any injuries or other damages resulting from the use of their products in any situation.
WARRANTY :
The non-transferable 2-year warranty covers only this Aqua Amp product and not any devices mounted in or on it. Users’ devices are not covered by a guarantee, and they subject them to known and unknown hazards at their own risk
FCC WARNING:
This equipment generates uses and can radiate radio frequency energy and, if
not installed
and used in accordance with the instructions, may cause harmful interference
to radio
communications. However, there is no guarantee that interference will not
occur in a
particular installation. If this equipment does cause harmful interference to
radio or
television reception, which can be determined by turning the equipment off and
on, the user
is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment must be installed and operated with a minimum distance of 15 cm between the radiator and user body.FCC ID: 2A64N-AA01ACT AquaAmp LLC certifies that this product complies with the EMC CE-RED Directive (2014/53/EU) and the EN 62368 standard. The CE compliance certificate can be accessed at aquaamp.com.
Parts Provided
Wireless Charger
Alcohol Wipe
Tools Required
2.5” Hole Saw
Electric Drill
Technical Information
Input Voltage Range| 10-30V DC
(12 / 24V system)
---|---
Input Current Max| 2A
Output Power| 10W (9V, 1.1A)
Standby current Draw| < 0.1W
Waterproof rating| Px6 front and back
Certifications| Qi, CE, FCC, ROHS,
UNECE R10 E24, RCM
Installation Guide
Step 1 : Drill or Cut 2.5” hole
Step 2: Use provided alcohol wipe to clean application surface. Remove adhesive backing from the wireless charger and insert the charger into hole
Step 3 : Using a 2A fuse, attach wires to a 12/24V power supply and ensure there is a waterproof connection
Step 4: Make sure the charger was installed correctly by placing a wireless charging compatible device in the center of the charger. Check that the device is charging a few seconds after it is placed.
Parts Provided
Wireless Charger
Alcohol Wipe
Tools Required
2.5” Hole Saw
Electric Drill
Technical Information
Input Voltage Range| 10-30V DC
(12 / 24V system)
---|---
Input Current Max| 2A
Output Power| 10W (9V, 1.1A)
Standby current Draw| < 0.1W
Waterproof rating| IPx6 front and back
Certifications| Qi, CE, FCC, ROHS, UNECE R10 E24, RCM
Installation Guide
Step 1: Drill or Cut 2.5” hole
Step 2: Use provided alcohol wipe to clean application surface. Remove adhesive backing from the wireless charger and insert the charger into hole
Step 3 : Using a 2A fuse, attach wires to a 12/24V power supply and ensure there is a waterproof connection
Step 4: Make sure the charger was installed correctly by placing a wireless charging compatible device in the center of the charger. Check that the device is charging a few seconds after it is placed.
Parts Provided
Wireless Charger
Alcohol Wipe
Tools Required
2.5” Hole Saw
OR
Straight Router Bit
Electric Drill
Technical Information
Input Voltage Range| 10-30V DC
(12 / 24V system)
---|---
Input Current Max| 2A
Output Power| 10W (9V, 1.1A)
Standby current Draw| < 0.1W
Waterproof rating| IPx6 front and back
Certifications| Qi, CE, FCC, ROHS,
UNECE R10 E24, RCM
Installation Guide
Step 1 : Determine whether the charger is to be installed flush with the surface (figure 1) or above the surface (figure 2). If the charger will be installed flush with the surface, refer to Step 2(a), otherwise, refer to Step 2(b).
Figure 1
OR
Figure 2
Step 2 (a): Route a 3.75” (95.0mm) diameter and 0.1” (2.5mm) deep pocket into the installation surface and drill or cut a 2.5” hole in the center of the pocket.
Step 2 (b): Drill or cut a 2.5” hole
Step 3 : Use provided alcohol wipe to clean application surface. Remove adhesive backing from the wireless charger and insert the charger into hole.
Step 4 : Making sure the charging emblem is centered over the installed
charger, place your choice of nonmetallic marine grade material over the
surface of the device.
The material chosen must be less than 0.1” (3.0mm).
Step 5 : Using a 2A fuse, attach wires to a 12/24V power supply and ensure there is a waterproof connection
Step 6: Make sure the charger was installed correctly by placing a wireless charging compatible device in the center of the charger. Check that the device is charging a few seconds after you place it on the wireless charger.
Parts Provided
Wireless Charger
Self tapping Screw (x4)
Tools Required
Phillips Head Screwdriver
Electric Drill
¼” Drill Bit
3/32” Drill Bit
Technical Information
Input Voltage Range| 10-30V DC
(12 / 24V system)
---|---
Input Current Max| 2A
Output Power| 10W (9V, 1.1A)
Standby current Draw| < 0.1W
Waterproof rating| IPx6
Certifications| Qi, CE, FCC, ROHS,
UNECE R10 E24, RCM
Installation Guide
Step 1 : Identify the installation location. The installation location should be an area that (1) is flat, allowing the back of the charger to be completely flush with the surface it is being mounted to and (2) is large enough to will allow the arms of the charger to reach its fully extended length (approximately 8.25”).
Step 2 : Place the provided alignment template in the installation location, using tape to secure it (if necessary). After double checking alignment and placement, use a drill and ¼” drill bit to drill the hole for the wire and a 3/32” drill bit to drill pilot holes for the screws. Remove the alignment template when completed.
Step 3: Insert the installation fixture into the charger. Thread the wire through the ¼” hole drilled in Step 2 and check for alignment of all four pilot holes to the mounting holes on the charger. Screw the charger in place using the provided screws. Remove the installation fixture and test that the arms extend and retract as expected using your phone.
Step 4: Using a 2A fuse, attach wires to a 12/24V power supply and ensure there is a waterproof connection
Step 5 : Make sure the charger was connected correctly by placing a wireless charging compatible device in the center of the charger. Check that the device is charging a few seconds after you place it on the wireless charger.
Technical Information
Input Voltage Range| 10-30V DC
(12 / 24V system)
---|---
Input Current Max| 2A
Output Power| 10W (9V, 1.1A)
Standby current Draw| < 0.1W
Waterproof rating| IPx6
Certifications| Qi, CE, FCC, ROHS,
UNECE R10 E24, RCM
customer support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>