StarTech com DKT31CDHPD3 USB-C Multiport Adapter User Guide

: June 9, 2024
: StarTech com

Table of Contents

Components And Function
Requirements
Package Contents
Installation
- Side A Ports
Regulatory Compliance
Disclaimer
Warranty Information
Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

StarTech com DKT31CDHPD3 USB-C Multiport Adapter User Guide

Components And Function

Component	Function
1	Built-in USB-C Host Cable

Connect to a USB-C Port on a Host Computer
USB 3.2 Gen 2 (10 Gbps)
Power Delivery 3.0 Specification

2| USB-C Data/Charge Port|

Connect and/or charge a USB-C Peripheral
USB-C Power Adapter required for charging
USB 3.2 Gen 2 (10 Gbps)
Supports 5 V/3 A (15 W) charging

3| 2x USB-A Data/Charge Port|

Connect and/or charge USB-A Peripherals
USB-C Power Adapter required for charging
USB 3.2 Gen 2 (10 Gbps)
Supports BC 1.2 5 V/1.5 A (7.5 W) charging
Via DisplayPort 1.4 DP Alt Mode

4| HDMI Output Port|

Connect an HDMI Display Device
HDMI 2.0b HDR10
Up to 4K (4096×2160) 60 Hz
Via DisplayPort 1.4 DP Alt Mode

5| DisplayPort Output Port|

Connect a DisplayPort Display Device
DisplayPort 1.4
Up to 4K (4096×2160) 60 Hz
Via DisplayPort 1.4 DP Alt Mode

6| USB-C 100 W Power

Delivery Port

|

Connect a USB-C Power Adapter
USB Power Delivery 3.0 (up to 100 W, with up to 85 W available for charging)

7

| Gigabit Ethernet Port|

Connect a CAT 5e/CAT 6 cable to establish a network connection
10/100/1000 Mbps

Requirements

Computer

DP Alt Mode enabled USB-C Port

For the latest drivers, manuals, product information, technical specifications, and declarations of conformance, please visit: www.StarTech.com/DKT31CDHPD3

Package Contents

USB-C Multiport Adapter x 1
Quick-Start Guide x 1

Installation

Side A Ports

Connect the Built-in USB-C Host Cable, located on the Multiport Adapter, to a USB-C Port on your Host Computer. Your Host Computer will automatically detect the Multiport Adapter and install the required drivers.
Connect a USB Peripheral Device to the USB-C Data/Charge Port, located on the Multiport Adapter.
Notes:
- Power and charge the connected Peripheral Device with up to 5 V/3 A (15 W).
- A USB-C power adapter must be connected to the USB-C 100 W Power Delivery Port, located on the Multiport Adapter, to charge Peripheral Devices.
- Without a power adapter connected, the USB-C Data/Charge Port will output whatever bus power is available, up to 4.5 W.
Connect USB Peripheral Devices to the USB-A Data/Charge Ports, located on the Multiport Adapter.
Notes:
- Power and charge the connected Peripheral Devices with up to 5 V/1.5 A
- (7.5 W).
- A USB-C power adapter must be connected to the USB-C 100W Power Delivery Port on the Multiport Adapter, in order to charge Peripheral Devices.
- Without a power adapter connected, the USB-A Data/Charge Ports will output whatever bus power is available, up to 4.5 W.
  Side B Ports
Connect a DisplayPort Enabled Display Device, to the DisplayPort Output Port, located on the Multiport Adapter, using a DisplayPort Cable.
Connect an HDMI Enabled Display Device, to the HDMI Output Port, located on the Multiport Adapter, using an HDMI cable.
Notes:
- This Multiport Adapter supports a single video signal output. If displays are connected to both the HDMI and DisplayPort Video Outputs, the Host Computer operating system will detect only one display, and both displays will show the same output.
- The Host Computer’s USB-C port must support DP Alt Mode in order to output video.
- Video performance, such as resolution, and refresh rate depends upon the connected Host Computer’s video controller. Please verify the specifications of the Host Computer.
  Side C Ports
Connect a USB-C Power Adapter (up to 100 W) from an AC outlet to the USB-C 100 W Power Delivery Port on the Multiport Adapter, to charge the Host Computer that’s connected to the Built-in USB-C Host Cable.
Note: The Multiport Adapter reserves 15 W of power, with up to 85 W available for charging your Host Computer.
Side D Ports
Connect a CAT 5e/CAT 6 cable from your Network Device (e.g. Router, Switch, Modem, etc.) to the Gigabit Ethernet Port on the Multiport Adapter, to access the network via a wired LAN connection.

Regulatory Compliance

FCC — Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause interference, and
This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Disclaimer

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of thirdparty companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a 3-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.