ATTENTION: Only suitable for children of at least 8 years of age. Instructions for parents or other responsible persons are enclosed and must be followed. Keep packaging as it contains important information.

General Warnings

Choking hazard — This product contains small parts that could be swallowed by children. This poses a choking hazard.
Risk of electric shock — This device contains electronic components that operate via a power source (batteries). Only use the device as described in the manual, otherwise you run the risk of an electric shock.
Risk of fire/explosion — Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.
Risk of chemical burn — Make sure you insert the batteries correctly. Empty or damaged batteries could cause burns if they come into contact with the skin. If necessary, wear adequate gloves for protection.
Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.
Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. Remove the batteries from the unit if it is not to be used for a long period of time, or if the batteries are empty!
Never recharge normal, non-rechargeable batteries. This could lead to explosion during the charging process.
Rechargeable batteries are only to be charged under adult supervision.
Rechargeable batteries are to be removed from the toy before being charged
The terminals must not be short-circuited.
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
Tools with sharp edges are often used when working with this device. Because there is a risk of injury from such tools, store this device and all tools and accessories in a location that is out of the reach of children.
Keep instructions and packaging as they contain important information.
The chemicals and liquids provided should be kept out of reach of children. Do not drink the chemicals! Hands should be washed thoroughly under running water after use. In case of accidental contact with the eyes or mouth rinse with water. Seek medical treatment for ailments arising from contact with the chemical substances and take the chemicals with you to the doctor.

Check the Power supply for damage to the cord, plug, enclosure or other parts on a regular basis before use. Do not use until the damage has been repaired. The toy is not intended for children under three years. The toy must only be used with the recommended power supply. The power supply is not a toy.
The toy is not to be connected to more than the recommended number of power supplies.

TIPS on cleaning

Remove the device from it’s energy source before cleaning (remove batteries) Clean the exterior of device with a dry cloth. Do not use cleaning fluids so as to avoid causing damage to electronic components.

Clean the lens (objective) only with the cloth supplied or some other soft lint-free cloth (e.g. micro-fibre). Do not use excessive pressure – this may scratch the lens.

Protect the device from dust and moisture. The batteries should be removed from the unit if it has not been used for a long time.

DISPOSAL

Dispose of the packaging material/s as legally required. Consult the local authority on the matter if necessary.

Do not dispose of electrical equipment in your ordinary refuse. The European guideline 2012/19/EU on Electronic and Electrical Equipment Waste and relevant laws applying to it require such used equipment to be separately collected and recycled in an environment-friendly manner. Empty batteries and accumulators must be disposed of separately. Information on disposing of all such equipment made after 01 June 2006 can be obtained from your local authority.

In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in the normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. Disposal in domestic waste violates the Battery Directive.

Batteries that contain toxins are marked with a sign and a chemical symbol.

battery contains cadmium
battery contains mercury
battery contains lead

EC Declaration of Conformity
Bresser GmbH has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the EU declaration of conformity is available at the following internet address: www.bresser.de/download/8851200/CE/8851200_CE.pdf

UKCA Declaration of Conformity
Bresser GmbH has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the UKCA declaration of conformity is available at the following internet address: www.bresser.de/download/8851200/UKCA/8851200_UKCA.pdf

Bresser UK Ltd. • Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain

All Parts

1. Eyepiece
2. Focus knob
3. Objective turret
4. Stage
5. Mirror
6. Electronic light source /battery compartment
7. Base
8. Rubber base
9. Microscope arm| 10. Microscope “Biotar”
11. Prepared Slides
12. Cover Plates
13. Blank Slides
14. CR2032 battery
15. Shrimp farming accessories
16. Microscope instruments
17. Micro-slicer
18. Hatchery
---|---

Your Microscope

What is a Microscope?
The microscope is made of two lens systems: the eyepiece and the objective. We’re presenting these systems as one lens each, so that it‘s easier to understand. In reality, however, the eyepiece (1) and the objective in the turret (3) are made up of multiple lenses. The lower lens (objective) magnifies the prepared specimen (e.g. 11), which leads to a magnified image of the specimen. The picture, which you can’t see, is magnified once more by the second lens (eyepiece, 1). Then, you can see the “microscope picture.”

Assembly and Location
Before you start, choose an ideal location for using your microscope. On the one hand, it‘s important there is enough light (normal observation). On the other hand, it’s important that you can quickly make the room dark when you want to (projector observation). Furthermore, I recommend that you place the microscope on a stable surface, since you won’t be able to get any satisfactory results on a shaky surface.

Normal Observation
For normal observation, place the microscope in a bright location (near a window or desk lamp, for example). Remove the microscope from the package and tilt the microscope arm (9) so that it’s in a comfortable viewing position for you.
The focus knob (2) is turned to the upper stop and the objective turret (3) is set to the lowest magnification.

Now, take a look through the eyepiece and adjust the mirror (5) so that you get a uniformly bright circle of light. Or, you can use the lamp. You’ll find further tips about the lamp in the next chapter.

Now, place a prepared slide (e.g. 11) under the clips on the stage (4), directly under the objective. When you take a look through the eyepiece, you can see the magnified specimen. At this point, it might still be a slightly fuzzy picture. The sharpness is adjusted by slowly turning the focus knob (2). You can now select a higher magnification by turning the objective turret and selecting a different objective.

In doing so, note that the sharpness of the picture must be adjusted again for the higher magnification. Also, the higher the magnification, the more light you will need for good illumination of the picture.

TIP: Avoid positioning the mirror so that it is exposed to direct sunlight, since it can cause a glare, which won’t allow you to get a clear picture.

Electric Illumination

NOTE! Before initial operation, the foil used for protecting the battery from discharging must be pulled out of the battery compartment.

Locate the mirror/light on the base of the microscope. Flip the mirror/light with the light facing up and press the button to power on the light. This microscope is equipped with an incandescent light that illuminates the specimen from below.

TIP: The higher the magnification used, the more light is required for a good illumination of the picture. Therefore, always start your experiments with one of the lower magnifications.

Battery change

Remove the safety screw from the cover.
Remove the battery cover.
Slide out the coin battery holder.
Install the CR2032 coin battery with the positive (+) polarity facing down and the negative (-) polarity facing up on the holder.
Replace the battery cover.
Screw in the safety screw back to the cover.

Experiments

Use the following web link to find interesting experiments you can try out. http://www.bresser.de/downloads
Microscope accessories can be found here: http://www.bresser.de/P8859480

Warranty

The regular warranty period is 2 years and begins on the day of purchase. To benefit from an extended voluntary warranty period as stated on the gift box, registration on our website is required.

You can consult the full warranty terms as well as information on extending the warranty period and details of our services at www.bresser.de/warranty_terms.

Contact
Bresser GmbH
Gutenbergstraße 2 46414 Rhede · Germany
www.bresser.de
@BresserEurope
Bresser UK Ltd.
Suite 3G, Eden House Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain
Errors and technical changes reserved.