Circutor Line-M-20I Impulse Centraliser User Manual
- June 9, 2024
- Circutor
Table of Contents
Line-M-20I Impulse Centraliser
User Manual
Line-M-20I Impulse Centraliser
This manual is a line-M-20I installation guide. For further information, please download the full manual from the CIRCUTOR web site: www.circutor.com
IMPORTANT!
The device must be disconnected from its power supply sources (power supply
and measurement) before undertaking any installation, repair or handling
operations on the unit’s connections. Contact the after-sales service if you
suspect that there is an operational fault in the device.
The device has been designed for easy replacement in case of malfunction.
The manufacturer of the device is not responsible for any damage resulting
from failure by the user or installer to heed the warnings and/or
recommendations set out in this manual, nor for damage resulting from the use
of non-original products or accessories or those made by other manufacturers.
DESCRIPTION
The line-M-20I is a centraliser with 20 digital inputs that is designed to centralise the logical status of each signal or to count the number of impulses received at each input.
INSTALLATION
The device must be installed on an electric panel or enclosure, attached to a DIN rail (IEC 60715).
IMPORTANT!
Before installing the line-M-20I, the device must bedisconnected from all
power supplies, both the powersupply itself and the measurement.
Only 2 line-M-20I centraliser can be connect to the rightof the line-EDS-Cloud
and line-TCPRS1 devices.
View the manuals M231B01-03-xxx and M239B01-03xxx for further information.
The steps to take to connect the devices are:
- Remove the protective covers of the expansion connector, which are located on the side of the devices, using a flat-tip screwdriver (Figure 1).
- Insert the expansion connector and fastening clips into one of the devices (Figure 2).
- Connect the two devices and fasten them by pushing the front clips down (Figure 3).
Figura 2
Figura 3
LEDs|
---|---
CPU| Device status
Flashing (White color):
Device powered
IN x| Digital input x status
ON (Green color):
Input activated
Technical features
Caracteristicas mecanicas Bornes| Mechanical features Terminals|
---|---|---
1 … 24| 1 … 24| 2.5 mm2 s 0.4 Nm, M2.5 plan° / flat
DImenslones| Dimensions| 52.5 x 118 x 70 mm
Peso| Weight| 130 g
Envolvente| Enclosure| Plastic° VO autoextinguible / Self-extinguishing VO
plastic
Mackin| Attachment| Carril DIN / DIN rail “}
Normas / Standars| |
EN 61010-1, EN 61000-6-2, EN 61000-6-4|
Connections
Entradas digitales Digital inputs
Terminal connections designations
| 1 | Common for digital input 1-5 | 13 | Common for digital input 11-15 |
|---|---|---|---|
| 2 | Digital input 1 | 14 | 11, Entrada digital 11 / Digital input 11 |
| 3 | Digital input 2 | 15 | 12, Entrada digital 12 / Digital input 12 |
| 4 | Digital input 3 | 16 | 13, Entrada digital 13 / Digital input 13 |
| 5 | Digital input 4 | 17 | 14, Entrada digital 14 / Digital input 14 |
| 6 | Digital input 5 | 18 | 15, Entrada digital 15 / Digital input 15 |
| 7 | Digital input 10 | 19 | Digital input 20 |
| 8 | Digital input 9 | 20 | Digital input 19 |
| 9 | Digital input 8 | 21 | Digital input 18 |
| 10 | Digital input 7 | 22 | Digital input 17 |
| 11 | Digital input 6 | 23 | Digital input 16 |
| 12 | Common for digital input 6-10 | 24 | Common for digital input 16-20 |
Dimensions
CIRCUTOR SAT: 902 449 459 (SPAIN) / (+34) 937 452 919 (out of Spain)
Vial Sant Jordi, s/n
08232 – Viladecavalls (Barcelona)
Tel: (+34) 937 452 900 – Fax: (+34) 937 452 914
e-mail : sat@circutor.com
References
- Productos y soluciones integrales para la eficiencia energética eléctrica
- Productos y soluciones integrales para la eficiencia energética eléctrica
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>