PATRIOT H8406 Exhaust Specific-Fit Headers Instruction Manual
- June 9, 2024
- PATRIOT
Table of Contents
H8406 Exhaust Specific-Fit Headers
1967-74 Models
Instruction Manual
H8406 Exhaust Specific-Fit Headers
4 PERTRONIX PERFORMANCE BRANDS EMISSIONS CODES
This Product Is considered a Replacement Part per CAIN and EPA regulations for
emissions compliance and Is legal for sale and use on specified vehicles In
all 50 states as stated in Manufacturers Application Guide and Installation
instructions.
1975-76 Model:
3 PERTRONIX PERFORMANCE BRANDS EMISSIONS CODES
This Product is LEGAL for Closed Course Competition use or Pre-Emissions
Controlled Vehicles .ONLY. It is Not Legal for use on any Emissions.
Controlled Vehicle four Street or Off Highway use.
PLEASE READ BEFORE PROCEEDING
PerTronix©thanks you for choosing a Patriot Exhaust Product. To realize the
potential of Patriot’s engineering and excellent fit, Please Read and
Understand these instructions completely prior to starting the installation.
Check that you received all the parts listed on the parts list, if you have
any concerns, please contact PerTronix before continuing. Headers will have
the part number stamped in the flange.
Work Smart — Work Safe! Most Header and Exhaust Installation are best
performed on a lift. If a lift is not available, raise the vehicle and support
on quality Jack Stands on level ground. Do not rely on a jack!
Many factors affect he installation of exhaust headers, including worn or
aftermarket motor mounts, previous accident damage, aftermarket cylinder heads
that may have relocated port or spark plug locations, suspension and steering
changes, sagging of original unibody structures due to age.
Coating Notes: Coatings can be marred during installation if you are not
careful. If you are breaking in a new motor, the extreme heat can alter the
appearance of the coating and this is not a warranty issue. We recommend
breaking in new motors with stock manifolds or an old set of headers.
We use sealing beads on all our headers. The raised bead creates a better seal
virtually eliminating leaks if installed properly. It is important to install
all header bolts lightly snug and then tighten to factory torque specs
starting in the center and working outward.
Before starting, allow the vehicle to cool, disconnect the battery, and spray
a penetrating oil on all hardware and fittings that will need to be removed.
Once you remove your manifold, clean the sealing surface on the head of any
old gasket debris or carbon build up.
DISASSEMBLY
-
Remove the exhaust crossover pipe from the manifolds if so equipped. Disconnect the exhaust pipes from the manifolds. Remove the hot air hose from the manifolds
to the air cleaner. Remove the manifolds from the motor. -
Clean the cylinder heads of any leftover gasket material or built up carbon.
-
On stick shift trucks, remove the clutch cross shaft.
-
On 65-66 trucks remove the bolt in crossmember under the bellhousing.
-
Remove the starter. Remove the A/C compressor brace to the manifold if equipped.
INSTALLATION
- Starting from below, raise the driver’s side header into position. It MAY be necessary to unbolt the motor mount and raise the engine 1-2”.
- Using the supplied gasket, header bolts and washers, bolt the header to the head. Tighten the bolts starting from the center and working out.
- Place a jack with a wood block under the oil pan. Remove the Passenger side motor mount bolt and lift the right side of the motor at least 2”.
- Some 65-67 trucks had a Water Cooled transmission. If yours has this, you may need to modify the coolant lines to clear the headers.
- From below, slide the passenger side header into place. Depending on your year, you may have to remove the motor mount stand from the frame if the header won’t slide in.
- Install two header bolts very loosely and reinstall the starter motor.
- If removed, replace the motor mount stand, then lower the motor and tighten up the motor mount bolt.
- With the gasket in place install the header bolts and washers. Tighten the bolts evenly starting from the center and working out.
- C6 transmission equipped trucks MAY need the shift linkage arm on the trans bent inward to clear the header.
- Connect the negative battery cable.
IMPORTANT CHECK LIST
- Be sure that all brake lines, transmission lines, and fuel lines are clear of headers and/or connector pipes.
- All spark plug wires, battery cables, or other electrical components should be clear of headers and/or connector pipes.
- If dipstick tube was removed, make sure it is installed properly and that the dipstick has been replaced.
- Double-check the tightness of all bolts including brackets and accessories.
START THE ENGINE
Start the engine and allow it to warm up to operating temperature. Check for
any unusual noises or exhaust leaks. If everything is OK, stop the engine and
tighten all bolts while the engine is still warm.
NOTE: Check the bolts periodically to make sure they have not loosened.
Re-tighten after the first 500 miles and then again at 1000 miles
Parts List
1 Left Side Header
2 Header Gaskets
2 Collector Gaskets
6 3/8-16 x 1 1/4” Hex Head Bolts| 1 Right Side Header
2 Reducers
16 3/8 X 1” Header Bolts
6 3/8-16 Hex Nuts
---|---
WARNING:
This product can expose you to chemicals including Lead, Nickel, Cadmium and
Chromium which are known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
PATRIOT EXHAUST LIMITED WARRANTY
All Patriot Headers and Exhaust products are guaranteed, to the original
purchaser, to be free of defects in material and workmanship for one year from
date of purchase. This warranty covers the replacement or repair of the
product and does not cover the cost of removal and installation, customer
applied coatings, or Any discoloration or corrosion of finished surfaces.
Damage or product failure resulting from collision, improper installation, off
road use, road hazards, the use of exhaust insulating wrap, or rust occurring
after installation is not covered by the warranty. This warranty extends only
to the original purchaser.
Should a part be deemed defective, it should be returned to the original
selling retailer and must be accompanied by the sales receipt. If there is no
retailer in your area, contact PerTronix direct for a return authorization and
return the part prepaid to the factory for inspection. PerTronix reserves the
right to replace or repair the alleged defective part and return the part
freight collect.
A PerTronix Performance Brand
^’www.pertronixbrands.com r‘) 909 599-5955
Installation Instructions & Warranty Information
H8406 ~ 1965-1976 Ford F-100, F150, F250 2WD 352-427 FE Long Tube Headers
Will Only fit factory Low Riser Truck 8 bolt cylinder heads.
May leak on passenger car heads
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>