PATRIOT H8012, H8013 Exhaust Clippster Header Instruction Manual

PATRIOT H8012, H8013 Exhaust Clippster Header

PLEASE READ BEFORE PROCEEDINGG
PerTronix”thanks you for choosing a Patriot Exhaust Product.

To realize the potential of Patriot’s engineering and excellent fit, Please Read and Understand these instructions completely prior to starting the installation.

Check that you received all the parts listed on the parts list. if you have any concerns. please contact Perlronix before continuing. Headers will have the part number stamped in the flange.

Work Smart-Work Safely Most Header and Exhaust Installation are best performed on a lift if a lift is not available, raise the vehicle and support on quality Jack Stands on level ground.

Do not rely on aa jack! Many factors affect he installation of exhaust headers, including worn or aftermarket motor mounts previous accident damage, aftermarket cylinder heads that may havoc relocated port or spark plug locations, Suspension and steering changes, sagging of original unibody structures due to age.

Installation Instructions & Warranty Information

H8012, H8013 ~ 396-502 Big Block 67-81 Camaro, 68-77 Nova, 68-77 Chevelle, Malibu, El Camino, 70-77 Monte Carlo, 65-74 Full Size Passenger Car & Wagon – Floor Shift Only Also fits Street Rods with Camaro Clip and Detroit Speed & Engineering Sub frames with Rack & Pinion Steering

Vehicles MUST have Original Style Big Block motor stands and motor mounts for Headers to fit properly. They are no longer available from G.M., but a reproduction is available from Classic Industries under P/N K702. If the motor is mounted on Small Block frame mounts, you will notice possible steering box and Idler Arm fit problems.
These headers will not fit a Saginaw 800 series close-ratio power steering box without modification due to the increased size of this power steering unit.
When installing an H8012 or H8013 a short oil filter, Fram Part # PH30 or equivalent, must be used.

DISASSEMBLY

1. Remove and mark all spark plug wires and then remove all spark plugs.
2. Disconnect the head pipes from the exhaust manifolds and remove the manifolds. Depending on the application, you may be required to remove the alternator, dipstick, clutch linkage, and/or oil filter. In some cases, it may be necessary to remove the starter and power steering unit. Only remove what is necessary to allow the removal of the manifolds or the installation of the headers.
3. Remove any gasket material or any carbon deposits that remain on the head surface.
4. At this point it may be necessary to cut the head pipes to allow room to install the headers. If you are installing a new exhaust system you may cut the head pipes any where you choose, but if you are using the existing exhaust you need to cut the head pipes in the proper location so that they will be able to be welded to the reducers supplied with your headers.

ASSEMBLY

1. Install the headers (Driver side from the bottom of the vehicle, passenger side from above).

2. Install all of the header bolts supplied and hand tighten. Tighten all the bolts evenly from the center out.

3. Install any accessories that were removed during the header installation.
   NOTE: Some accessories require different brackets than stock and some require the addition of spacers between the bracket and header flange. An example would be on some Chevy ap plications the driver’s side front bolt must use the original (factory) bolt and use the supplied spacer between the flange and the accessory bracket.

4. Install the reducers and determine the connection to the exhaust system.

5. Weld the reducers to the exhaust system and install them onto the headers utilizing the gaskets and bolts supplied.

6. Install the spark plugs and connect the wires to the proper plug. If the spark plugs have a lot of miles on them, now would be a good time to replace them with PerTronix Flame Thrower Wires. When you install the spark plugs, apply a small amount of anti-seize to the threads.

7. Check to make sure that all the wiring, brake lines, hoses, etc. are clear of the headers or any exhaust component.

8. Re-connect the battery cable.

IMPORTANT CHECK LIST

• Be sure that all brake lines, transmission lines, and fuel lines are clear of headers andlor connactor pipos.
• All spark plug wires, battery cables, or other electrical components should be clear of headers and/or connector pipes.
• If dipstick tube was removed, make sure it is installed properly and that the dipstick has been replaced.
• Double-check the tightness of all bolts including brackets and accessories

START THE ENGINE
Start the engino and allow it to wam up to operating temporature. Check for any unusual noisos or exhaust leaks. If everything is OK, stop the engine and tighten all bolts while the engine is still warm.
NOTE: Check the bolts periodically to make sure they have not loosened. Re-tighten after the first 500 miles and then again at 1000 miles

Parts List

• 1 Left Side Header
• 2 Header Gaskets
• 6 3/8-16 Nuts
• 2 Reducers
• 4 Right Side Header
• 16 3/8-16 X 1” Header Bolts
• 6 3/8-16 X1 Hex Bolts

PATRIOT EXIHALST LINTED WARRANTY

All Patriot Headers and Exhaust products are guaranteed, to the original purchaser, to be free of defects in material and workmanship for one year from date of purchase. This warranty covers the replacement or repair of the product and does not cover the cost of removal and installation, customer applied coatings, or Any discoloration or corrosion of finished surfaces. Damage or product failure resulting from collision, improper installation, off road use, road hazards, the use of exhaust insulating wrap, or rust occurring after installation n is not covered by the warranty. This warranty extends only to the original purchaser.

Should a part be deemed defective, it should be returned to the original selling retailer and must be accompanied by the sales receipt. If there is no retailer in your area, contact Perlronix direct for a return authorization and return the part prepaid to the factory for inspection. PerTronix reserves the right to replace or repair the alleged defective part and return the part freight collect.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>