THORN BORIS Gen2 Sensor Remote Control Instruction Manual
- June 9, 2024
- THORN
Table of Contents
THORN BORIS Gen2 Sensor Remote Control
Installation Instructions
| SAP Code | Product Description | Voltage | HZ | IP | IK | Height (H) | Size(mm) |
|---|---|---|---|---|---|---|---|
| 96635768 | BORIS PLUG&PLAY MWS SENSOR GEN2 | DC12V-24V | 5.8GHz±75MHz | 65 | 08 | ||
| 4-12m | 50×34.4 | ||||||
| 96635769 | BORIS PLUG&PLAY PIR SENSOR GEN2 | DC12V-24V | / | 65 | 03 | 4-12m |
55×43.4
96635770| BORIS SENSOR REMOTE CONTROL GEN2| 2 x AAA 1.5V| /| /| /| /| /
Sensor commissioning
NOTE: Sensor needs to be commissioned by remote control. No default setting.
- Press button, the remote control leds will show the stored parameters.
- Press enter in the setting condition, the parameter leds of remote control will flash to be selected, navigate to the desired setting by pressing to select the new parameters.
- Press ok to confirm all setting and saving.
- Aim at the target sensor and press to upload the new parameter, the luminaire will flash to confirm settings received.
Sensor commissioning using Modes
- Press remote LED indicators show stored parameters.
- Press to select new parameters if required.
- Press to confirm parameters set and update selected mode.
- Press to upload parameters.
Default Mode Settings
Product
|
Scenario
|
Brightness
|
Sensitivity
|
Hold Time
| Stand-by Time| Stand-by Dim Level|
Daylight Sensor
---|---|---|---|---|---|---|---
MWS| Mode 1| 100%| 75%| 5 min| | 0%| OFF
MWS| Mode 2| 100%| 75%| 5 min| 30 min| 10%| OFF
PIR| Mode 3| 100%| 100%| 5 min| | 0%| OFF
PIR| Mode 4| 100%| 100%| 5 min| 30 min| 10%| OFF
WARNING
Remove the batteries from compartment if the remote will not be used in
30days.
Installation Instructions
MWS SENSOR GEN2
PIR SENSOR GEN2
WARNING
NOTE: Warm up time is 15 seconds. After the sensor connects input power,
the light will keep on 15 seconds,then go to dimming to work normally.
WARNING
NOTE: Warm up time is 40 seconds. After the sensor connects input power,
the light will keep on 40 seconds, then go to dimming to work normally.
DIGRAM
Warning!
Reflected HF Waves(e.g. of walls,floors, ceilings or furniture)from other
transmitters affect motion detection.
MWS SENSOR GEN2
PIR SENSOR GEN2
WARNING:
-
Ensure that any installation and maintenance be performed by a qualified electrician and that luminaire be wired in accordance with the latest IEE electrical regulations or the local equipments.
-
Ensure that the power supply is off before perform installation and maintenance and not switched on until the installation or maintenance complete.
-
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
Caution: Risk of electric shock -
If the external flexible cord of this luminaire is damaged, it shall be exclusively replaced by themanufacturer or his service agaent or a similar aualified person in order to avoid a hazard.
-
Only to be installed outside arms reach.
Thorn Lighting Limited, Durhamgate, Spennymoore, Co Durham, DL16 6HL, UK Zumtobel Lighting GmbH, Schweizer Strasse 30,6850 Dornbirn, Austria
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>