Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight Instruction Manual

June 13, 2024
Lightology

Lightology logo Installation Instructions for
Entra CL3 Round or Square Type IC, Air-tight
New Construction Adjustable LED Housing
ENCL3
920ENTRACL3Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air
Tight

ENERAL RODUCT NFORMATION

This product is suitable for indoor locations.
This product can be dimmed with a standard electronic dimmer.
This instruction shows a typical installation.
CAUTION RISK OF FIRE
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°C supply conductors.
SAVE THESE INSTRUCTIONS!

Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight -
Fig1

Install the Housing with Adjustable Bars

Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight -
Fig2

  1. Determine which direction the adjustable bars need to be mounted, they can either be mounted horizontally or vertically.
  2. Slide the inner adjustable bar completely through the two slots. Make sure flange at bottom of hanger bar ends is orientated with the bottom of the housing.
  3. Slide and push the outer adjustable bar completely onto the inner adjustable bar so that the tab clicks into place behind the stop point. This will prevent the adjustable bars from coming apart.
  4. Repeat steps 1 & 2 for the other side of the housing.Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight - Fig3 NOTE: The adjustable bars can be mounted to joists that are spaced 16″ – 24″ apart.
  5. Align the bottom of the end plates with the bottom of the ceiling joists.
  6. Level the adjustable bars and, with a hammer, tap the nails completely into the joists to secure the adjustable bars in place.Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight - Fig4
  7. Adjust the collar’s position (horizontal position) by sliding the housing on adjustable bars.
  8. When the desired location is achieved, tighten the screws to lock the housing onto the adjustable bars.
    NOTE: Notches in collar can be used to align multiple housings using a laser or string.

Connect Power to the Housing

  1.   Push the tab on the housing electrical box up and remove the electrical box cover.
  2. Install the conduit to the housing electrical box.
  3. Run the power line wires into the housing electrical box.
  4. Use the following wiring diagram to wire your fixture.
  5. Make sure to cap 0-10V dimming wires if not being used.

Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight -
Fig6

Install Drywall

Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight -
Fig7

  1. Mark an appropriate sized diameter circle or square on drywall. Cut out the marked section.
    Note: The drywall may be cut by running a 1/8″ Root Zip around the outside of the collar.Lightology 920ENTRACL3 Entra CL3 Round Or Square Type
IC Air Tight - Fig8

  2. Align the cut out section of drywall with the collar and install drywall.
    Install the Plaster Ring (Flangeless Version Only) Lightology
920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight -
Fig92 Install the provided 6×20 self-drilling screws through the plaster plate and housing at the marked locations. Do not place screws at any of the other mud holes on the plate.Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight -
Fig10

  3. Properly plaster onto the plaster ring and drywall
    Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight -
Fig11

  4. Finish around the fixture to match drywall.

Assemble the Fixed or Adjustable Trim/Light Module

Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight -
Fig12

NOTE: Trim is included with flanged versions only. Skip this step for flangeless versions where plaster ring is provided.

  1. Press the spring clips inward and feed the reflector through the trim until they snap together.Lightology 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight - Fig13
  2. Carefully snap light module and reflector together. Alignment arrows are provided on the adjustable versions. Directional alignment is not required for fixed Versions.

Assemble the Wall Wash Light Module

  1. Remove and discard optic holder and optic from fixed light module.
  2. Snap light module and wall wash reflector together

Install the Light Module

  1. Connect the jumper cable to the housing wire making sure the port marked “B” is paired with the port with a black line.
  2. Push the spring clips inward.
  3. Insert the light module through the collar and into housing.
  4. Release the spring clips to secure in place

Adjust the Module (Adjustable Versions Only)

  1. Using your fingers, adjust the direction of the light making sure to turn the module not the reflector (see note below).
    NOTE: The light module may be rotated up to 45 degrees when inside the housing. Remove the module from the housing to rotate another 45 degrees if necessary, then carefully reinstall the module into the

Install or Replace Optics and Lenses/Louvers

  1. Unscrew and remove the optic holder from the light module.

  2. Remove the old optic.

  3. If installing a lens or louver, remove the rubber gasket from the optic holder to allow room for lens or louver installation. If not installing a lens or louver, skip this step.
    NOTE: Only one lens or louver may be installed at a time.

  4. Install the new optic into the optic holder.

  5. Make sure the lens, louver, optic or gasket are properly seated in the optic holder, then screw the optic holder back onto the light module

©2022 Tech Lighting, L.L.C. All rights reserved. The Tech Lighting logo is a registered trademark of Tech Lighting. Tech Lighting reserves the right to change specifications for product improvements without notification.

Lightology logo7400 Linder Ave., Skokie, IL 60077
T 847.410.4400
F 847.410.4500
www.techlighting.com
VISUAL COMFORT& CO

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals