KICHLER 44349PNLED 1-Light Polished Nickel Modern-Contemporary LED Wall Sconce Instruction Manual

KICHLER 44349PNLED 1-Light Polished Nickel Modern-Contemporary LED Wall

Sconce

Fixture Diagram

Parts List

• [A] Mounting Strap
• [B] Outlet Box
• [C] Strap Mounting Screws
• [D] Canopy
• [E] Flat Head Screws
• [F] Glass
• [G] Main Body

Cautions
CAUTION – RISK OF SHOCK Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.
WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
DIMMING:
This LED fixture is compatible with most standard incandescent dimmers, LED dimmers, and electronic low voltage dimmers. For optimal performance, an electronic low voltage dimmer should be used.
CLEANING:

• Always be certain that electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

Installation Instructions

1. Attach mounting strap[A] to outlet box[B] using the strap mounting screws[C]. Mounting strap can be adjusted to suit position of fixture.

2. Grounding instructions: (See Illus. a or b).
   a) On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
   b) On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, then thread into mounting strap. If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

3. Make wire connection. Reference chart below for correct connections and wire accordingly.
   Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
   ---|---
   Black| White
   Parallel cord (round & smooth)| Parallel cord (square & ridged)
   Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
   Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
   *Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)| ****

Neutral Wire

4. Push fixture to wall. NOTE: Fixture can be mounted with glass in the up or down position. NOTE: Make sure all wires are inside canopy and do not get pinched between canopy and wall.
5. Use the two (2) flat head screws[E] to secure the canopy to the wall by threading into the sides of the canopy[D]. Tighten to secure.
6. Carefully install the glass[F] by gently lowering onto the main body[G] and rotate into place as shown.

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• IS-45723LED-US

Documents / Resources

| KICHLER 44349PNLED 1-Light Polished Nickel Modern-Contemporary LED Wall Sconce [pdf] Instruction Manual
44349PNLED 1-Light Polished Nickel Modern-Contemporary LED Wall Sconce, 44349PNLED, 1-Light Polished Nickel Modern-Contemporary LED Wall Sconce, Polished Nickel Modern-Contemporary LED Wall Sconce, Modern-Contemporary LED Wall Sconce, LED Wall Sconce, Wall Sconce, Sconce
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>