BRESSER TNS2 Wifi Thermal Night Vision Instruction Manual
- June 9, 2024
- BRESSER
Table of Contents
TNS2 Wifi Thermal Night Vision
Instruction Manual
TNS2 Wifi Thermal Night Vision
APP DOWNLOAD:
http://www.bresser.de/download/9630900/App_Download_on_Google_Play_Store_Bresser_Thermal_Telescope.htmlhttp://www.bresser.de/download/9630900/App_Download_on_Apple_AppStore_Bresser_Thermal_Telescope.html
MANUAL & APP DOWNLOAD:
www.bresser.de/download/9630902
Google Play and the Google Play logo are trademarks of Google Inc.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S.
and other countries. App Store is a service mark of Apple Inc., registered in
the U.S. and other countries.
ABOUT THIS INSTRUCTION MANUAL
These operating instructions are to be considered a component of the device.
Please read the safety instructions and the operating instructions carefully
before use.
Keep these instructions for renewed use at a later date. When the device is
sold or given to someone else, the instruction manual must be provided to the
new owner/user of the product.
GENERAL WARNINGS
RISK OF CHOKING!
Keep packaging material, like plastic bags and rubber bands, out of the reach
of children, as these materials pose a choking hazard.
RISK OF ELECTRIC SHOCK!
This device contains electronic components that operate via a power source
(power supply). Children should only use the device under adult supervision.
Only use the device as described in the manual; otherwise, you run the risk of
an electric shock.
Disconnect the device from the power supply by pulling the power plug when it
is not used. In case of longer interruption of operation and before starting
any work on maintenance and cleaning. Always pull on the plug to separate the
device from the power supply. Never pull on the cable.
RISK OF FIRE/EXPLOSION!
Do not expose the device to high temperatures. Use only the supplied power
supply. Do not short-circuit the device. Excessive heat or improper handling
could trigger a short circuit, a fire, or an explosion.
NOTE!
Do not disassemble the device. In the event of a defect, please contact the
Service Centre in your country.
Do not immerse the unit in water.
Do not subject the unit to excessive force, shock, dust, extreme temperature
or high humidity, which may result in malfunction, shorter electronic life
span, damaged batteries and distorted parts.
When the product works, slight click will be given out every several seconds.
This is the normal phenomenon that the lens captures the image.
INTRODUCTION
This Thermal Night Vision device adopts advance non-cooled focal plane
infrared detector and quality optical lenses as the core. With the
characteristics of convenient and quick operating system, small appearance
design, expansion parts with perfect function, long duration of use, it is
sturdy and durable and applicable to all types of environments and provides an
ideal temperature measurement tool featuring “clear imaging, precise
measurement, simple operation and easy to carry”. This is the best selection
for onsite detection, preventive maintenance and other application sites.
The product may be used for outdoor animal observation, search and rescue,
law enforcement detection for policemen, night patrol, outdoor activities and
personal security, etc. The product is provided with the photographing
function. The photos may be browsed by connecting with a computer through USB
to make it convenient for observation of many persons at the same time, which
creates possibility for application in more occasions.
SCOPE OF DELIVERY
- Thermal Night Vision device
- USB cable
- Power supply adapter (for use with USB cable)
- Case
- Instruction Manual
BATTERY CHARGING INSTRUCTIONS
Use USB data line to charge:
This product has a built-in rechargeable battery.
When the battery is low, please charge it in time via the Micro USB port.
After fully charged, unplug the USB cable.
Note: When the battery is completely empty, there will be an abnormality.
It is recommended to use the battery when it is sufficient.
PARTS OVERVIEW
OPERATING
CHARGING
The product is provided with built-in battery.
When the battery power is not sufficient, please charge it through Micro USB
interface in time.
POWER ON/OFF
Hold down [ ** ] key to power on /off.
IMAGE CAPTURE
Press [ ] key to capture the image. The screen will show [ ] prompt,
indicating that image cap- ture is successful.
VIDEO CAPTURE
Video recording is only possible via the WIFI app.
IMAGE REVIEW
After powering on, short press the [ ** ] key to enter the image viewing
mode (the image shows the last imagetaken), press the [ ] key to view the
previous image, press the [ ] key to view the next image, and press the [
**] key to exit Image viewing mode.
DELETE IMAGE
After entering the image viewing mode, press and hold the [ ] key to delete
the currently viewed image.
IMAGE EXPORT
Capture and save images can be viewed and ex- ported via a Micro USB
connection to a computer.
MODE SWITCHING
Press the [ ] button to switch between the four imaging modes of rainbow,
iron oxide red, white heat and black heat.
ZOOM IN/OUT
Under the power-on state, press the [ ] key, and each time you press it, the
target of “2X, 4X” will be gradually enlarged and displayed. Press again to
return to the normal state.
BRIGHTNESS ADJUSTMENT OF THE DISPLAY SCREEN
Under the power-on state, press and hold the [ ] key to adjust the
brightness. Each long press adjusts the brightness by 1 level.
DIOPTER ADJUSTMENT
Rotate the diopter adjustment button left and right to adjust the diopter for
yourself.
FOCUSABLE LENS
Rotate the focus lens button left and right to focus. Rotate clockwise for
near focus and counterclockwise for far focus.
INDICATOR LIGHT**
| Status | Not being charged | In charging | Fully charged |
|---|---|---|---|
| Power on | Blue | Red blue (purple) | Blue |
| Power off | None | Red | None |
APPLICATION OF AMPLIFICATION
The magnification function may be utilized whenremote objective is
photographed so as to observe the objective clearly. The effect picture is as
follows:
| |
---|---|---
Normal| 2X| 4X
APPLICATION OF COLOR PALETTE
The color palette menu may change the pseudo color of infrared thermal image
and provide six types of color palettes: rainbow, iron oxide red, white heat,
black heat, yellow, bird watching. The selection of proper color palette can
show the details of target object in a better manner. The color palette of
rainbow and iron oxide red focuses on display of color and is very suitable
for the condition of high heat contrast and used to improve color contrast
between high temperature and low temperature. On the other hand, the colour
palettes white heat and black heat provide a greyscale image. White heat is
particularly suitable for detection at greater distances.
The image effect photographed with six types of color palette.
UNDER-FLOOR HEATING, TERRESTRIAL HEAT AND LEAKAGE POINT – DETECTION SKILL
- Heat the floor for 3 minutes.
- Adjust the ambient light to darkest. Stabilize the instrument and not shake it. Stand to detect large area.
- Pieces of pipes appears in non leakage image. The locality of leakage point is red.
- A large area of red appears if floor temperature is high. The effect is better if reducing tempera- ture first and rising it up again.
Note:
- Suggest that the under-floor temperature is above 40° C. The preheating time is more than 3 minutes. (Make adjustment according to depth of under-floor heating pipe concretely).
- Don’t be too close to the floor. Suggest making observation for large area.
- The locality of leakage point will appear a imaging area.
- If the temperature is too high, it needs to turn off the under-floor heating. Rise temperature of the under-floor heating for detection after the floor reduces to normal temperature.
WIFI FUNCTION & APP DOWNLOAD
First install the app on your smartphone.
Download (AppStore or Google Play):
http://www.bresser.de/download/9630902
Now press and hold the [ ] button for 3 seconds to start the WIFI function.
Search for “FPVWIFI****”under open Wifi networks on your smartphone
andconnect to it. Enter the password: “wifi12345678”.
Now open the app. After pressing Start, the connection to the camera is
established.
- Start screen
- Take photos
- Record videos
- Playback
- Picture rotation
- Screen view
Press and hold the [ ] button for 3 seconds to stop the Wifi function and to
disconnect the camera.
VIDEO OUTPUT
Connect an external screen via the SMA socket of the video output and switch
on the unit. To start the video output function (CVBS), press and hold the [ ]
key for 3 seconds. The screen now switches to the display of the external
screen. Press and hold the key again for 3 seconds to exit the mode.
MENU
Press and hold the [ ] key for 3 seconds to open the menu. Press and hold the
button again for 3 seconds to exit the menu.
| Button | Description |
|---|---|
| **** | • Press and hold the key to enter the menu. |
• Press the key briefly to confirm in the menu.
**| Return to the previous menu or exit menu.
| Navigate upwards in the menu.
| Navigate down in the menu.
Function| Description
---|---
Colour| Colour palettes: white hot, black hot, rainbow, red hot, yellow, bird
watching.
The default value is white hot.
Brightness| 10 brightness levels (0-9). The default value is 5.
Contrast| 10 contrast levels (0-9). The default value is 5.
HOT| Hotspot tracking: automatic tracking of multiple hotspot destinations (on
or off).
The default value is off.
PI| Perfect image: (PI+, PI-) (0-4).
The default value is “PI- 3”.
Language| Language selection: English (EN), German (DE), Spanish (ES).
The default value is English (EN).
Photo| Display images: Press the [ ** ] to display the first picture. Press
[ ] for up or [ ] for down to change the picture. Long press the [ ] to
delete the current picture. Press [ ] again briefly to end the picture
display.
WIFI| WIFI:
On or off. The default value is off.
---|---
System| System:
RES: Reset
UPGR: Update
UPGR:
Connect the unit to the computer via USB at start-up, copy the upgrade file
config.txt to the unit’s
SD card, then disconnect the USB connection, open the menu, press the up [ ]
or down [ ] key to
select the “Firmware Upgrade” option, press the [ **** ] to perform the
upgrade. If it is not successful,
please repeat the upgrade steps, reboot the unit, connect the unit to the
computer via USB and delete the upgrade file. Remember: The upgrade file
cannot be renamed and the file extension
cannot be changed, otherwise the upgrade will fail!
TECHNICAL DATA
| Probe type | Uncooled focal plane |
|---|---|
| Resolution ratio | 384×288 infrared focal plane |
| LCD resolution | 720X540 |
| Focus length | 19mm; 25mm; 35mm |
| Eyepiece | Single eyepiece display (the dioptric compensation is adjustable) |
| Field angle | 19.5°x14.7°; 14.9°x11.2°; 10.7°x 8° |
| Digital zoom | 2X; 4X |
Discovery range (the object can be
discovered, but it is not yet possible to identify what exactly it is)| Boar:
1471 m Vehicle: 2501 m
Detection range (from this range the object can be detected)| Boar: 367 m
Vehicle: 626 m
Wavelength coverage| 8μm-14μm
Frame rate of thermal images| 50Hz
Color palette| Rainbow/iron oxide red/white heat/black heat
Focusing mode| Adjustable
Image storage| BMP
Battery| Built-in rechargeable batteries
USB| Micro USB
Working time| ≥15 hours
Work temperature| 0 °C to 45 °C
Storage temperature| -20 °C to 60 °C
Product size| 186x69x68 mm
Product weight| 440g
DISPOSAL
DISPOSAL
Dispose of the packaging materials properly, according to their type, such as
paper or cardboard. Contact your local waste-disposal service or environmental
authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage! As per
Directive 2002/96/ EC of the European Parliament on waste electrical and
electronic equipment and its adaptation into German law, used electronic
devices must be collected separately and recycled in an environmentally
friendly manner.
EC DECLARATION OF CONFORMITY
** Hereby, Bresser GmbH declares that the equipment type with part number:
9630902 is in compliance with Directive: 2014/53/ EU. The full text of the EU
declaration of conformity is available at the following internet address:
www.bresser.de/download/9630902/CE/9630902_CE.pdf
WARRANTY**
The regular warranty period is 5 years and begins on the day of purchase. You
can consult the full warranty terms as well as information on extending the
warranty period and details of our services at:
www.bresser.de/warranty_terms.
Please contact the service centre first for any questions regarding the
product or claims, preferably by e-mail.
E-Mail: service@bresseruk.com
Telephone: +44 1342 837 098
BRESSER UK Ltd.
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
United Kingdom
Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone
provider); calls from abroad will involve higher costs.
Contact Bresser GmbH
Gutenbergstraße 246414 Rhede · Germany
www.bresser.de
@BresserEurope
References
- Bresser | Startseite | Expand Your Horizon mit BRESSER
- index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>