Pioneer DJ OPUS-QUAD Professional All In One DJ System Instruction Manual

: June 10, 2024
: Pioneer DJ

Table of Contents

OPUS-QUAD Professional All In One DJ System
IMPORTANT SAFETY INSTRUCTIONS
Specifications
LIMITED WARRANTY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OPUS-QUAD Professional All In One DJ System
Instruction Manual

OPUS-QUAD Professional All In One DJ System

pioneerdj.com/support/
rekordbox.com
For FAQs and other support information for this product, visit the above site.
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
D3-4-2-1-1_B1_En
WARNING
This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.
D3-4-2-1-3_A1_En
WARNING
This product is equipped with a three-wire grounding (earthed) plug – a plug that has a third (grounding) pin. This plug only fits a grounding-type power outlet. If you are unable to insert the plug into an outlet, contact a licensed electrician to replace the outlet with a properly grounded one. Do not defeat the safety purpose of the grounding plug.
D3-4-2-1-6_B1_En
WARNING
To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
Operating Environment
Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light).
D3-4-2-1-7c_A2_En
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 5 cm at each side).
D3-4-2-1-7d_A1_En
CAUTION
The u switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).
D3-4-2-2-2a_A1_En
The graphical symbol ∼ placed on the product means alternating current.
The graphical symbol **placed on the product means direct current.
The graphical symbol placed on the product means Class II equipment.
D3-8-2-4_A1_En
CAUTION
This product is evaluated in moderate and tropical climate condition.
D3-8-2-1-7a_A1_En
[for a service technician] CAUTION
Since the fuse may be in the neutral of the mains supply, disconnect the mains to de-energize the phase conductors.
WARNING
Store small parts out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately.
D41-6-4_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest service center or your dealer for a replacement.
**S002_A1_En
switch
Turns this unit on or puts this unit into standby mode.

This unit should not be used by persons who have heart pacemakers installed, since adverse effects could occur.
Do not use this unit in hospitals or clinics, or near medical equipment.
Do not use inside airplanes or in the vicinity of automatic doors to avoid danger of causing malfunctions.

For Europe
**If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.
K058b_A1_En
For Finland customers
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan
For Norway customers
Apparatet må tilkoples jordet stikkontakt
For Sweden customers
Apparaten skall anslutas till jordat uttag
For Denmark customers
Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord.
D3-4-2-1-6b_C1_En
For U.S.A., U.S. Territories, and Canada
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe level – a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing “comfort level” adapts to higher volumes of sound, so what sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:**

Set your volume control at a low setting.
Slowly increase the sound until you can hear it comfortably and clearly, without distortion.
Once you have established a comfortable sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

Do not turn up the volume so high that you can’t hear what’s around you.
Use caution or temporarily discontinue use in potentially hazardous situations.
Do not use headphones while operating a motorized vehicle; the use of headphones may create a traffic hazard and is illegal in many areas.

S001a_A1_En
[Supplied power cord]
The supplied power cord is designed specifically for 120 V. Do not use it with a voltage other than 120 V.
Doing so may cause a fire or electric shock.
D3-7-14_PDJ_A1_En
For U.S.A. and U.S. Territories
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF THIS EQUIPMENT ARE ON THE REAR.
RECORD THESE NUMBERS ON PAGE 16 FOR FUTURE REFERENCE.
*D36-AP9-3_A1_En**

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Product Name: ALL-IN-ONE DJ SYSTEM
Model Number: OPUS-QUAD
Responsible Party Name: AlphaTheta Music Americas, Inc. OPERATIONS DIVISION
Address: 2050 W. 190th Street, Suite 109, Torrance, CA 90504, U.S.A.
Phone: 1-424-488-0480
URL: pioneerdj.com
*D8-10-4_C1_En
NOTE:**
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_A1_En
Information to User
Alterations or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.
D8-10-2_A1_En
CAUTION
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.
D8-10-3a_A1_En
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
5.15 GHz – 5.25 GHz band is restricted to indoor operations only.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
For Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
5.15 GHz – 5.25 GHz band is restricted to indoor operations only.
High-power radars are allocated as primary users (i.e. priority users) of the bands 5.25 GHz – 5.35 GHz and 5.65 GHz – 5.85 GHz and that these radars could cause interference and/or damage to LE-LAN devices.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).

Specifications

General
Power requirements ……………….AC 110 V – 240 V, 50 Hz / 60 Hz
Power consumption ……………………………60 W
Power consumption (standby)………………….0.3 W
Main unit weight ………………………. 13.2 kg / 29.1 lbs.
Max. external dimensions …………………….(W × D × H) 925.7 × 499.7 × 142 mm / 36.44” x 19.67” x 5.59”
Tolerable operating temperature ………………… +5 °C – +35 °C (+41 °F – +95 °F)
Tolerable operating humidity …………………………5 % – 85 % (no condensation)
Audio Section
Sampling rate ……………………….44.1 kHz
MASTER D/A converter ……………………. 32bit
Other A/D and D/A converters……………………….. 24bit
Frequency characteristic
USB, LINE, MIC 1, MIC 2 …………………………20 Hz – 20 kHz
S / N ratio (rated output, A-WEIGHTED)
USB ……………………………………………….114 dB
LINE …………………………………..96 dB
PHONO ………………………………85 dB
MIC …………………………………….79 dB
Total harmonic distortion (20 Hz – 20 kHz BW)
USB …………………………………..0.003 %
LINE ……………………………0.005 %
Standard input level / Input impedance
LINE ………………………….. -12 dBu / 47 kΩ
PHONO ………………………. -52 dBu / 47 kΩ
MIC ……………………… -57 dBu / 3 kΩ
Standard output level / Load impedance / Output impedance
MASTER 1 ………………..+6 dBu / 10 kΩ / 360 Ω or less
MASTER 2 ………………………+2 dBu / 10 kΩ / 700 Ω or less
ZONE …………………………..+6 dBu / 10 kΩ / 360 Ω or less
BOOTH ……………+6 dBu / 10 kΩ / 700 Ω or less
PHONES …………………+8 dBu / 32 Ω / 1 Ω or less
Rated output level / Load impedance
MASTER 1 …………………………..+25 dBu / 10 kΩ
MASTER 2 ……………………..+21 dBu / 10 kΩ
Crosstalk
LINE………………………………………..84 dB
Channel equalizer characteristic
HI ………………………………….. -26 dB – +6 dB (20 kHz)
MID ……………………………… -26 dB – +6 dB (1 kHz)
LOW ………………………………………-26 dB – +6 dB (20 Hz)
Microphone equalizer characteristic
HI ……………………………….. -12 dB – +12 dB (10 kHz)
MID ……………………………. -12 dB – +12 dB (2.5 kHz)
LOW ………………………-12 dB – +12 dB (100 Hz)
Input / Output terminals
LINE / PHONO input terminals
RCA pin jacks ………………………………….2 sets
MIC input terminals
XLR connector & 1/4” TRS jack …………………2 sets
MASTER 1 output terminal
XLR connector ……………………………………………… 1 set
MASTER 2 output terminal
RCA pin jacks …………………………………….. 1 set
ZONE output terminal
XLR connector ………………………………….. 1 set
BOOTH output terminal
1/4” TRS jack ………………………………………………….. 1 set
PHONES output terminal
1/4” stereo jack ………………………………………………. 1 set
3.5 mm stereo mini-jack …………………………… 1 set
USB terminals
USB Type-A ……………………………………………..3 sets
Power supply…5 V / 1 A or less
USB Type-C ……………………………………1 set
LINK terminal (PRO DJ LINK)
LAN terminal (1000BASE-T) ………………………… 1 set
Wireless LAN section
Supported standards……………………………………… IEEE 802.11 a / b / g / n / ac
Frequency band used ……………………. 2.4 GHz / 5 GHz
Bluetooth ®/MD section
Wireless system …………………….. Bluetooth Ver.4.2
Maximum transmission distance …. Approximately 20 m* in unobstructed circumstances.
Frequency band used ………………………….2.4 GHz
Modulation method …………………………… FH-SS (Frequency Hopping Spread Spectrum)
Compatible Codecs…………………………………… SBC, AAC

Transmission distances are a guideline. Transmission distance may change depending on the surrounding environment.
- The specifications and design of this product are subject to change without notice.

Trademarks and registered trademarks

Wi-Fi is a registered trademark of Wi-Fi Alliance®.
The Bluetooth ®/MD word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by AlphaTheta Corporation is under license. Other trademarks and trade names are those of their respective owners.

Connect headphones to either the phone jack or mini jack terminal. Connecting headphones to both terminals simultaneously may impair the sound quality or reduce the volume.
Use a USB cable with a length of 2 m or less.
For wired LAN connections, Use a Cat5e (or higher) STP cable.
Be careful not to accidentally insert the power cord of other products into the [MASTER 1] terminal or [ZONE] terminal.
Do not connect devices that can supply phantom power to the [MASTER 1] terminal or [ZONE] terminal.
Be sure to use the [MASTER 1] terminal and [ZONE] terminal as balanced output. Using an XLR-RCA conversion cable (conversion adapter) to connect to an unbalanced input (such as RCA) may cause the sound quality to drop and noise to occur. For connection to an unbalanced input (such as RCA), use the [MASTER 2] terminal.

Available wireless LAN channels in each country

Country Code.	Available Channels

*** For outdoor use of wireless LAN, please follow the relevant country’s regulations.
For Europe
**

| BE| BG| CZ| DK| DE| EE| IE| EL
---|---|---|---|---|---|---|---|---
ES| FR| HR| IT| CY| LV| LT| LU
HU| MT| NL| AT| PL| PT| RO| SI
SK| FI| SE| NO| IS| LI| CH| TR

W52, W53 (5150 MHz – 5350 MHz) Indoor use only.
For Europ
Declaration of Conformity with regard to the Radio Equipment Directive 2014/53/EU
Manufacturer:
AlphaTheta Corporation
6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 Japan
[]　OPUS-QUAD
Hereby, AlphaTheta declares that the radio equipment type [] is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: https://pioneerdj.com/en/support/product- compliance-documents

| Output power| Frequency band(s)
---|---|---
Wireless LAN (2.4GHz)
Wireless LAN (5GHz) W52
W53
W56
W58
Bluetooth| + 17.0 dBm Max
+ 16.5 dBm Max
+ 17.5 dBm Max
+ 17.5 dBm Max
+ 10.5 dBm Max
+ 5.5 dBm Max| 2400 MHz – 2483.5 MHz
5150 MHz – 5250 MHz
5250 MHz – 5350 MHz
5470 MHz – 5725 MHz
5725 MHz – 5875 MHz
2400 MHz – 2483.5 MHz

AlphaTheta Music Americas, Inc.

LIMITED WARRANTY

WARRANTY VALID ONLY IN THE U.S.A. AND CANADA
ONE YEAR LIMITED WARRANTY
AlphaTheta Music Americas, Inc. (COMPANY) warrants that Pioneer DJ branded products distributed by COMPANY in the U.S.A. and Canada that fail to function properly under normal use and conditions due to a manufacturing defect when installed and operated according to the owner’s manual enclosed with the unit, and any officially published guidelines such as technical specifications or service communications, will be repaired or replaced with a unit of comparable value, at the option of COMPANY, without charge to you for parts or actual repair work. Parts supplied under this warranty may be new or rebuilt at the option of COMPANY.
This warranty is valid only in the country of purchase. This limited warranty applies to the original or any subsequent owner of this product during the warranty period provided the product was purchased from an authorized company distributor/dealer in the U.S.A. or Canada. You will be required to provide a sales receipt or other valid proof of purchase showing the date of original purchase or, if rented, your rental contract showing the place and date of first rental. In the event Service is required, the product must be delivered within the warranty period, transportation prepaid, only from within the U.S.A or Canada, as applicable. As explained in this document, you will be responsible for removal and installation of the product. COMPANY will pay to return the repaired or replacement product to you within the U.S.A or Canada, as applicable.
PRODUCT WARRANTY PERIOD
Parts
Labor
1 Year
Audio and Video …………………
The warranty period for retail customers who rent the product commences upon the date product is first put into use (a) during the rental period or (b) retail sale, whichever occurs first.
WHAT IS NOT COVERED
IF THIS PRODUCT WAS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR, THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND THIS PRODUCT IS SOLD STRICTLY “AS IS” AND “WITH ALL FAULTS”.
COMPANY SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL AND/OR INCIDENTAL DAMAGES, INCLUDING WITHOUT LIMITATION LOSS OF USE, LOSS OF PROFITS OR LOSS OF WAGES, TO THE GREATEST EXTENT ALLOWED BY APPLICABLE LAW. COMPANY’S LIABILITY SHALL UNDER NO CIRCUMSTANCE EXCEED THE ACTUAL AMOUNT PAID BY YOU FOR THE DEFECTIVE PRODUCT.
This warranty does not apply if the product has been subjected to power in excess of its published power rating.
This warranty does not cover the cabinet or any appearance item, user attached antenna, any damage to records or recording tapes or discs, any damage to the product resulting from alterations, modifications not authorized in writing by COMPANY, accident, misuse or abuse, damage due to lightning or power surges or caused by events beyond COMPANY’s reasonable control, subsequent damage from leaking, damage from inoperative batteries, or the use of batteries not conforming to those specified in the owner’s manual.
This warranty does not cover the cost of parts or labor which would be otherwise provided without charge under this warranty obtained from any source other than a COMPANY authorized service company or other designated location. This warranty does not cover defects or damage caused by the use of unauthorized parts or labor from improper maintenance.
Altered, defaced, or removed serial numbers void this entire warranty.
This warranty does not cover ordinary wear and tear, damage caused by tampering, abuse, or neglect of the product, or damage caused by parts not provided by company.
COMPANY and its service and repair facilities are not responsible for damage or loss of electronic information or data stored on any returned product.
NO OTHER WARRANTIES
COMPANY LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO A PERIOD NOT TO EXCEED THE WARRANTY PERIOD. NO WARRANTIES SHALL APPLY AFTER THE WARRANTY PERIOD. Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusions or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights which may vary from state to state.
No dealer, distributor, or employee of COMPANY is authorized to make any modification, extension, or modification of this warranty.
If any term of this warranty is held to be illegal or unenforceable, the legality or enforceability of the remaining terms shall not be affected or impaired.
TO OBTAIN SERVICE
COMPANY has appointed a number of Authorized Service Companies throughout the U.S.A. and Canada should your product require service. To receive warranty service you need to present your sales receipt or, if rented, your rental contract showing place and date of original owner’s transaction. If shipping the unit, you will need to package it carefully and send it, transportation prepaid by a traceable, insured method, to an Authorized Service Company. Package the product using adequate padding material to prevent damage in transit. The original container is ideal for this purpose. Include your name, address and telephone number where you can be reached during business hours.
On all complaints and concerns in the U.S.A. and Canada call Customer Support at 1-844-784-0000.

For information on hook-up or operation of your unit or to locate an Authorized Service Company, please call or visit:
Website: pioneerdj.com
Phone: 1-844-784-0000

DISPUTE RESOLUTION
Following our response to any initial request to Customer Support, should a dispute arise between you and COMPANY, COMPANY makes available its Complaint Resolution Program to resolve the dispute. The Complaint Resolution Program is available to you without charge. You are required to use the Complaint Resolution Program before you exercise any rights under, or seek any remedies, created by Title I of the Magnuson-Moss Warranty-Federal Trade Commission Improvement Act, 15 U.S.C. 2301 et seq. To use the Complaint Resolution Program call 1-844-784-0000 and explain to the customer service representative the problem you are experiencing, steps you have taken to have the product repaired during the warranty period and the name of the authorized Distributor/Dealer from whom the Pioneer DJ branded product was purchased. After the complaint has been explained to the representative, a resolution number will be issued. Within 40 days of receiving your complaint, COMPANY will investigate the dispute and will either: (1) respond to your complaint in writing informing you what action COMPANY will take, and in what time period, to resolve the dispute; or (2) respond to your complaint in writing informing you why it will not take any action.
RECORD THE PLACE AND DATE OF PURCHASE FOR FUTURE REFERENCE
Model No. ____ Serial No. ____ Purchase Date __
Purchased From ___
KEEP THIS INFORMATION AND YOUR SALES RECEIPT IN A SAFE PLACE
UCP0620-A1

© 2022 AlphaTheta Corporation. All rights reserved.
AlphaTheta
6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 JAPAN
AlphaTheta EMEA Limited
Artemis Building, Odyssey Business Park, West End Road, South Ruislip, Middlesex, HA4 6QE, U.K. TEL: +44-203-7617-220
AlphaTheta Music Americas, Inc.
2050 W. 190th Street, Suite 109, Torrance, CA 90504, U.S.A. TEL: +1 424-488-0480
AT_001_all_01
Printed in Malaysia