i safe MOBILE IS-TH1xx.RG Rugged Hand Held Barcode Scanner User Guide

IS-TH1xx.RG Rugged Hand Held Barcode Scanner
User Guide
MODEL MTHA10/MTHA11

INTRODUCTION

This document contains information and safety regulations which are to be observed without fail for safe operation of the device IS-TH1xx.RG (Model MTHA10/ MTHA11) under the described conditions. Non-observance of this information and instructions can have serious consequences and/or may violate regulations.
Please read the manual and these safety instructions before using the device. In case of any doubt, the German version shall apply.
The current EU/UK-declaration of conformity, certificates, safety instructions and manuals can be found at www.isafe-mobile.com or requested from i.safe MOBILE GmbH.

RESERVATION

The content of this document is presented as it currently exists. i.safe MOBILE GmbH does not provide any explicit or tacit guarantee for the accuracy or completeness of the content of this document, including, but not restricted to, the tacit guarantee of market suitability or fitness for a specific purpose unless applicable laws or court decisions make liability mandatory. i.safe MOBILE GmbH reserves the right to make changes to this document or to withdraw it any time without prior notice. Changes, errors and misprints may not be used as a basis for any claim for damages. All rights reserved.
i.safe MOBILE GmbH cannot be held responsible for any data or other loss and direct or indirect damages caused by any improper use of this device.

EU/UK-DECLARATION OF CONFORMITY
The EU/UK-declaration of conformity can be found at the end of this manual.
NAME CONCEPT
The two “xx” in IS-TH1xx.RG are placeholders. The IS-TH1xx.RG comes in two variants with different scan ranges and scan engines:

FAULTS AND DAMAGES

If there is any reason to suspect that the safety of the device has been compromised, it must be withdrawn from use and removed from any ex-hazardous areas immediately.
Measures must be taken to prevent any accidental restarting of the device. The safety of the device may be compromised, if, for example:

• Malfunctions occur.
• The housing of the device shows damage.
• The device has been subjected to excessive loads.
• The device has been stored improperly.
• Markings or labels on the device are illegible.

We recommend that a device displaying errors or in which an error is suspected be sent back to i.safe MOBILE GmbH to be checked.

FURTHER SAFETY ADVISES

CAUTION
Laser Light. Do not stare into beam class 2 laser product 630 – 680 nm, 1 mW.

• To ensure the IP-protection, it has to be ensured that all gaskets are present and functional.
• There must be no large gap between the halves of housing.
• The device may not be exposed to any aggressive acids or alkalis.
• Only accessories approved by i.safe MOBILE GmbH may be used.
• Do not put the device in environments with excessive temperatures.
• Do not use the device in areas where regulations or legislatives prohibit the use.
• Do not expose the device to strong magnetic fields, such as are emitted from induction ovens or microwaves.
• Do not attempt to open or repair the device. Improper repair or opening can lead to the destruction of the device, fire or explosion. Only authorized personnel are allowed to repair the device.
• Observe all corresponding laws that are in force in the respective countries regarding the use of devices while operating a vehicle.
• Please power off the device before cleaning the device.
• Do not use any chemical cleaning agents to clean the device. Use a damp and anti-static soft cloth for cleaning.
• The user alone is responsible for any and all damages and liabilities caused by malware downloaded when using the network or other data-exchange functions of the device. i.safe MOBILE GmbH cannot be held responsible for any of those claims.

WARNING
i.safe MOBILE GmbH will not assume any liability for damages caused by disregarding any of these advices or by any inappropriate use of the device.

MAINTENANCE/REPAIR

Please note any legal requirements for periodic inspection.
The device itself has no user-serviceable parts. It is recommended to perform inspections according to the safety regulations and advises. If there is a problem with the device, please contact your vendor or consult the service center. If your device is in need of repair, you can either contact the service center or your vendor.

PRODUCT DESCRIPTION

1. HOLDER: Holder for IS530.RG
2. PLUG: Connecting IS530.RG
3. SCAN BUTTON: Scanning barcodes.
4. EYELET: Eyelet for hand strap.

INSTALLATION

WARNING
The device may be connected only outside ex-hazardous areas to the IS530.RG via the ISM interface!

• Unscrew the cover of the ISM interface (1) located on the IS530.RG.
• Push the IS530.RG completely into the holder (2) of the device.
• Unscrew the screw (3).
• Loosen the plug (4).
• Attach the plug on top of the ISM interface (5).
• Fix the plug by pressing the rounded end of the plug (6).
• Tighten the screw (7).
• Check whether the plug is correctly and firmly attached to the ISM interface.

RECYCLING
The crossed-out wheeled-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European Union. Do not dispose of these products as unsorted municipal waste. Always return your used electronic products, batteries, and packaging materials to de- dicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. More detailed information is available from the product retailer, local waste authorities, national producer responsibility organisations, or your local i.safe MOBILE GmbH representative.
Correct Disposal of this product. This marking indicates that this product should not be dispose other household wastes throughout the EU. To prevent possible harm to the environment or human he from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

TRADEMARKS

• i.safe MOBILE and the i.safe MOBILE logo are registered trademarks of the i.safe MOBILE GmbH.

CONTACT/SERVICE CENTRE
FOR FURTHER QUESTIONS PLEASE CONTACT OUR SERVICE CENTRE:

• i.safe MOBILE GmbH, i_Park Tauberfranken 10, 97922 Lauda-Koenigshofen, Germany
• support@isafe-mobile.com
• https://support.isafe-mobile.com

EU/UK-DECLARATION OF CONFORMITY

EU/UK – Declaration of Conformity
according to directive 2014/30/EU, SI 2016 No. 1091, 2014/35/EU, SI 2016 No. 1101, 2011/65/EU (2015/863/EU) and SI 2012 No. 3032
The company i.safe MOBILE GmbH declares under its sole responsibility that the product to which this declaration relates is in accordance with the provisions of the following data, directives and standards:

Name & address of the manufacturer in the EU| i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda – Koenigshofen
Germany
---|---
Description of the devices| Trigger Handle
Type: IS-TH1MR.RG and IS-TH1ER.RG
Model: MTHA10 and MTHA11
Conformity statement 2014/30/EU, 2014/35/EU and 2015/863/EU amending 2011/65/EU issued by| Shenzhen TCT Testing Technology Co., Ltd.
1B/F., Building 1, Yibaolai Industrial Park, Qiaotou, Fuyong, Baoan District, Shenzhen, Guangdong, China
Applied harmonized standards| EN 55032:2015; EN 55035:2017;
EN 62368-1:2014+A11:2017;
IEC 62321-2:2013;
IEC 62321-3-1:2013; IEC 62321-5:2013;
IEC 62321-4:2013 + AMD1 2017;
IEC 62321-7-1:2015; IEC 62321-7-2:2017;
IEC 62321-6:2015; IEC 62321-8:2017;
EN 60825-1:2014; EN62471:2008
Conformity statement SI 2016 No. 1091, SI 2016 No. 1101 and SI 2012 No. 3032 issued by| Shenzhen TCT Testing Technology Co., Ltd.
1B/F., Building 1, Yibaolai Industrial Park,
Qiaotou, Fuyong, Baoan District, Shenzhen,
Guangdong, China
Applied standards| BS EN 55032: 2015; BS EN 55035: 2017;
BS EN 62368-1: 2014 + A11: 2017;
BS EN 62321-2: 2014; BS EN 62321-3-1: 2014;
BS EN 62321-5: 2014;
BS EN 62321-4: 2014 + AMD1: 2017;
BS EN 62321-7-1: 2015; BS EN 62321-7-2: 2017;
BS EN 62321-6: 2015; BS EN 62321-8: 2017
 CE/UKCA Marking|

Lauda – Koenigshofen 02.02.2022

Document No. 1056MM01REV02
Version: 2022-10-31
(c) 2022 i.safe MOBILE GmbH
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen,Germany
Tel. +49 9343/60148-0
info@isafe-mobile.com
www.isafe-mobile.com
Template: TEMPMM01REV10
1056CC19REV00_jru All rights reserved, i.safe MOBILE GmbH

References

• AT&T Official Site | Our Best Wireless & Internet Service
• Zertifizierte Smartphones, Tablets und Mobiltelefone für IECEx und ATEX Zonen
• Support - Official i.safe MOBILE Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>