Tenda MW5 Nova AC1200 Whole Home Mesh WiFi System Installation Guide
- June 4, 2024
- Tenda
Table of Contents
Tenda MW5 Nova AC1200 Whole Home Mesh WiFi System Installation Guide
Package contents
MW5 (2-pack)
- Mesh5 x 1
- Power adapter x1
- Ethernet cable x 1
- Mesh5s x 1
- Quick installation guide x 1
Know your device
1 Install the Tenda WiFi App
Download the Tenda WiFi App on to your mobile device by searching for Tenda WiFi in the Google Play/App Store, or by scanning the QR coda. Then install the Tenda WiFi App.
http://download.cloud.tenda.com.cn/down/app
2 Connect the Primary Node (Mesh5)
Tips
If you do not a modern for internet access, please skip steps 1 and 3.
- Power off your modem.
- Use the included Ethernet cable to connect the WAN/LAN port to your modem or the Ethernet jack.
- Power on your modem
- Power on the primary node, and wait until the LED indicator blinks green.
3 Connect the Primary Node (Mesh5) to the Internet
-
Connect the mobile phone to the WIFI network of the primary node. The SSID and password can be found on the bottom label of the device.
-
Run the Tenda WIFI App and follow the on-screen to moonboot the devolo to the Internet. After the device is connected to the internet, its LED indicator lights solid green.
4 Connect the Secondary Nodes (Mesh5s) to the Internet
-
Place each node·
• At a high and open area.
• Ensure that the wall between any two nodes is less than two.
• Keep your nodes away from electronics with strong interference, such as microwave oven, induction cooker, and refrigerator. -
Power on the secondary nodes, and their LED indicators light solid green. Wait about for 40 seconds. The secondary node is connecting to the primary node when its LED indicator blinks green. The MW5 (3-pack} is taken as an example here.
-
Observe the LED indicators of the secondary nodes until the LED indicator light one of the following colors:
-
If the secondary node’s LED indicator does not solid grana, relocate it according to step 1 in IV & nodes (Me&h5s) to the latent to get an optimal connection quality.
Done.
– To access the internet with:
• Wired devices: Connect wired device5 to the LAN ports of your
nodes.
• Wireless devices: Connect wireless devices to your WiFi network using the
SSID and password you set.
– If you configure the nodes using the Tenda WiFi App and you went to manage
the network remotely, tape on the App home page end use your account to log
in.
FAQ
Q1. How can I change my SSID and password?
A1. Run the Tenda WIFI App, navigate to settings > Wire less Snellings to change your SSID and password, and tap Save. After your SSID and password are changed, you need to reconnect your mobile devices using the new SSID and password.
Q2.How can I remove a node from my WFI network?
A2. Tap the node on the Tenda WiFi App, tap .. in the upper-right
comer, and choli Delete.
Note; This removing operation restores the node to factory
settings.
Q3. Can I add a new node to expand my network coverage?
A3. Yes. Runt he Tenda WIFI App, navigate to Settings >Add nova, and follow the on-screen instructions to add.
Q4. How to restore my network to factory settings?
A4. When your device is working properly, hold down the reset (RSTJ button of your primary node using a needle-like item (Such as a pin) for about 6 seconds, and release it when the LED indicator blinks fast. Your network: is reset successfully when the LED indicator lights solid on and then blinks again And all nodes are restored to factory settings.
Q5. My2.4 GHz WIFI-enabled devices, such as a home security
camera, cannot connect to my nova WIFI network. What should I do?
AS. (1) Connect your smartphone to your nova WiFi network.
(2) Run the Tenda WiFi App, navigate to Settings > Smart Assistant, and tap
Enable. Your smartphone connects to the 2.4 GHz WiFi network.
(3) Use the smartphone to set up your 2.4 GHz WiFi- enabled device as guided
by its App
LED Indicator status
CE Mark Warming
https://www.tendacn.com/download/list-9.html
FCC Statement
RECYCLING
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>