EXVIST V519 Data Transfer Unit 4G or 3G Industrial Router User Manual

: June 5, 2024
: EXVIST

Table of Contents

Interface
Description for Indicator
Preparation
Dashboard
Interface
Network
Application
System
FCC Caution.
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V519 Data Transfer Unit 4G or 3G Industrial Router
**User Manual

Data Transfer Unit
Model: V519
4G/3G Industrial Router 4G/3G
Serial Server User Manual
ModelV519**

Interface

RJ45 Jack: LAN0
RJ45 Jack: LAN1
DC Jack: DC7V~35V wide voltage, DC12V is better and recommended.

Description:
LAN0 can be used as WAN under regular router mode;
DC: 2.1mm Standard Round Interface, 7V~35V, Internal:+, Outside: –

3G/4G/WIFI Antenna: SMA external rotation internal hole interface.
RESET: press for >5s when it’s powered on, SYS indicator will flash quickly and it’ll reboot. Then all settings will be reset to the default factory settings.
Serial Port: 4PIN PH2.0mm, GND/TX/RX/DC+ from left to right, DC+ can be used power supply to power on the router.
SIM card slot: Self-locking slot, press the white button on your left side and it will pop out.

Description for Indicator

Name	Status	Description
(SYS)	Indicat or On	Powered and connected properly
Flash Quickly	Abnormal connection: 3G/4G dialing: system reset

GND , TX, RX, DC+

Currently, UART1 can only be used as RS232, it’s GND/TX/RX/DC+ from left to right. But for data transmission, only GND/TX/RX will be used, respectively connecting them to the 5PIN, 2PIN, and 3PIN of the computer’s serial port to establish serial communication. DC+ works as the input and output connector of the power supply. (E.g.: when input is 12V, then the output voltage is 12V too.)
Description of Antenna Port:
There’re three SMA antenna ports, that is 3G/4G, and 2x WiFi antenna ports. Users can select the appropriate antennas. Theoretically, the higher gain the antenna has, the better transmitting and receiving the effect of WiFi it will be. For a 3G/4G antenna, it’s recommended to use 3-5dB antenna. But for WiFi antenna, it depends on your requirement and coverage and supports max. 15dB.

Preparation

2.1 Connection
Correctly insert the SIM card and power on the router with a DC12V adapter.
2.2 Configure IP for PC
Before accessing the router from browsers, it’s recommended for you to set your PC as “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then it will get an IP address automatically by the router. If you would like to set one assigned address for your PC, it’s necessary to set it in the same network segment of LAN0 of the router (the default IP address for LAN0: 192.168.8.1, subnet mask: 255.255.255.0).
2.3 Connected to WiFi
Check whether there’s a WiFi hotspot started with V519-XXXXXX(SSID), then click “connect” and enter the password (87654321 by default) to establish a wireless connection.
2.4 Confirm whether the PC is well connected to the router
After obtaining the IP address, please execute the PING command to double confirm whether the PC is well connected to the router. Take Windows as an example: WIN+R Enter “cmd” Enter “ping 192.168.8.1”, if it’s shown like the below photo, then it means the PC is well connected to the router:
2.5 Access router from a browser

Start a browser like Chrome, Firefox, Edge, etc.
Enter http://192.168.8.1 in the address column
Enter username and password (admin by default) and it’s shown as below:

After login, you will be able to configure and manage this router.

Dashboard

On this page, it’s easier to view the status of the router. Click the registered courier and you will see the detailed information of 4G as below:

Interface

On this page, it’s easier to view the status of 4G LTE, LAN, and Switch as below:

Network

5.1 LTE
This page, it allows users to configure LTE. By default, it’s LTE Gateway mode for V519, just inserting a 4G/3G SIM card, later router will auto recognize and register to the corresponding network of 4G/3G. You can also configure and select ISP.
5.2 Custom APN
Please enter the APN information provided by ISP. The APN information of the domestic three ISPs for your reference as below:

ISP	3G/4G	APN	Diol Number	User	Password
Chino Mobile	TD-SCDMA
TD-LTE, GSM	cement	*99#	blank	blank

Application

6.1 VPN Client
OpenVPN, L2TP, PPTP, GRE tunnel and other VPN protocols are supported. Before setting, please try to obtain the related parameters of VPN server first.

6.2 LTE GPS
LTE GPS is one of the optional features because it uses the GPS built-in in the 4G modules. If it’s required to enable GPS, please go to Network–>LTE–>GPS and enable GPS. If it positions successfully, you will see the map below.
6.2.1 GPS Data Upload
It allows users to upload GPS data to the assigned server:
6.2.2 GPS Server
Once enabled, GPS data will be broadcasted via the assigned port. But for the terminal connected to the router, all you have to do is to open the corresponding port to get the GPS information.

6.3 Serial Port
Only 1ch RS232 can be supported. RS485 can be customized if required. The serial port can also be worked as GPS positioning, terminal command line, ModBus, data transparent transmission.

System

7.1 Device
In this page, it allows users to change operation mode and system language.
7.1.1Operation Mode
5x operation modes can be selected: LTE Gateway (By Default), Gateway, 2.4G WISP, AP, Mix. Please see below photo:
1. LTE Gateway
By default, it’s LTE Gateway mode, all you have to do is to insert a 3G/4G SIM card, then the router will auto recognize and register to the corresponding network of 3G/4G. You can also custom and select your ISP.
2. Gateway
When you’re ready to use “Gateway” mode (standard wireless router mode), the WAN port of the router should be connected to the modem via ethernet cable to dial.
1) Obtain an IP address automatically
Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot. Later please access the router from the browser again, and go to Network->LAN-> Select “DHCP” from the dropdown list of Dial Mode ->Click “Confirm” and then the router will obtain an IP address automatically from the ISP.
2) Manually Set IP
Please go to System->Device->Operation Mode->Select “Gateway”->Confirm,then the router will reboot. Later please access the router from the browser again, and go to Network->LAN->Select “Static IP” from the dropdown list of Dial Mode ->Enter IP address, Subnet Mask, Gateway, DNS, and other parameters you get from ISP->Click “Confirm”
3) PPPoE
Please go to System->Device->Operation Mode->Select “Gateway”->Confirm, then the router will reboot. Later please access the router from the browser again, and go to Network->LAN-> Select “PPPoE” from the dropdown list of Dial Mode ->Enter username, password, and other parameters you get from ISP->Click “Confirm”
3. 2.4G WISP

Please go to System->Device->Operation Mode->2.4G WISP; 2) Click “Scan” and it’ll pop up one dialog window of all searched wireless
network, select one, and enter a username, and password if required to connect.
4. AP (Access Point)
Please go to System->Device->Operation Mode->Select “AP”->Confirm. Try to connect the WAN port of V519 to the LAN port of the primary router via ethernet cable, then it can turn your wired network into a wireless network.
5. Mix
In the Mix mode, it supports 4G, wired, and wireless backup. When it’s failed to connect to the network for the main connection, the router will auto switch to the backup module to make sure the router can connect to the Internet normally.

Go to System->Device->Operation Mode->Select “Mix”
After rebooting, go to Network->Connection->Set Main Connection as “LTE” and Alternate Connection as “WAN”:
Enter the corresponding parameters, click “confirm” and the router will reboot
Insert SIM card and set parameters of 4G, and connected to 4G successfully.
Set wireless connection and enter related parameters:
Click “Interface” and you’ll see it’s all connected to 4G and WiFi:

7.6 Manage Server
This page, it allows users to configure the parameters of the remote management server. After configuration, the router can be connected to the remote server, through remote server, it’s okay to configure the router. But for the remote management server, a customized integration protocol will be required. Please contact your seller for more details.

FCC Caution.

§ 15.19 Labelling requirements.
his device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
§ 15.21 Information to the user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF warning for Mobile devices:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.