VELOSSA TECH 2014-2022+ Toyota 86/FRS/BRZ BIG MOUTH Ram Air Intake Installation Guide
- July 21, 2024
- VELOSSA TECH
Table of Contents
- VELOSSA TECH 2014-2022+ Toyota 86/FRS/BRZ BIG MOUTH Ram Air Intake
- Product Information
- Product Usage Instructions
- FAQs
- Kit Contents
- Stock Components Removal
- Big Mouth Installation
- Bracket 3 Installation
- Bracket 1 Installation
- Bracket 2 Installation
- Clip Bracket 3
- Tighten Bracket 3
- Clip Brackets 1 and 2
- Fasten Upper Section
- Final Assembly Review
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
VELOSSA TECH 2014-2022+ Toyota 86/FRS/BRZ BIG MOUTH Ram Air Intake
Product Information
Specifications:
- Compatibility: 2014-2022+ Toyota 86/FRS/BRZ
- Installation Time: 2 hours
- Tools Required: Basic hand tools
Product Usage Instructions
Kit Contents:
| Qty | Item |
|---|---|
| 2 | M6 x 25mm Cap Screw |
| 6 | #8 x 3/4 Flat Head Phillips Screw |
| 1 | Push Retainer Clip |
| 1 | M6 Lock Nuts |
Stock Components Removal:
Before starting the installation, remove the OEM snorkel and OEM plastic plate. Consult specific instructions on how to remove the bumper for your trim model.
Big Mouth Installation:
Position the top of the BIG MOUTH first, keeping it loose. Slide the bottom section into place before fastening.
FAQs
Q: How do I ensure proper alignment during installation?
A: Follow the provided instructions carefully, ensuring screws are inserted at the correct angles and not over-torqued. Patience and manual tightening are key to proper alignment.
Q: What should I do if I encounter any binding or preload issues after installation?
A: Review the assembly, loosen and retighten components as needed for proper adjustment. Check for any parts causing interference and make necessary corrections.
Kit Contents
Please review this document before attempting installation.
You will need basic hand tools and 2 hours of installation time.
Stock Components Removal
It is best to google “how to remove bumper” for your particular trim, after the bumper is removed, you will see the following.
Big Mouth Installation
The top of the BIG MOUTH slides into position as shown, DO NOT fasten yet. Keep it loose so the bottom section can easily slide into position.
Bracket 3 Installation
Bottom section first needs Bracket 3 to be installed, do not tighten the screws all the way yet. These screws should be left somewhat loose until you position the bottom body correctly.
Bracket 1 Installation
Slide the bottom half of the BIG MOUTH ducting into the position as shown, it should tuck under the top half of the BIG MOUTH assembly first. Begin to screw in Bracket 1, ensure that the dovetail joint that hooks into the body is secure.
Note the angle by which the screws must enter the assembly, they will self tap. Be sure to slowly screw them in by hand (do not use an electric drill to drive these screws as you risk mis-aligning them and damaging the body by over-torquing).
Bracket 2 Installation
Bracket 2 will be installed similarly to bracket 1. Engage the hook and screw by hand slowly, note the 45-degree angle by which to insert the screws. Be patient with alignment.
Clip Bracket 3
All brackets should be in place. You will need to go under the crash bar and insert the supplied Christmas-tree clip to fasten bracket 3 to the crash bar (there is a hole in the crash bar).
Tighten Bracket 3
Once Bracket 3 has been clipped into the crash bar, you may tighten these screws with a Phillips screwdriver. The slots in the bracket allow there to be adjustment.
Clip Brackets 1 and 2
Insert the OEM clips as shown. These clips will securely snap brackets 1 and 2 into the crash bar.
Fasten Upper Section
Once the lower body is secure, you may fasten the upper body as shown.
Final Assembly Review
Review the install and make sure nothing is binding or causing any preload on any parts, loosen and retighten if adjustment is necessary.
