Jimi IoT LL301 Lte Cat1 Asset Gnss Tracker User Manual
- June 9, 2024
- Jimi IoT
Table of Contents
- LL301 Lte Cat1 Asset Gnss Tracker
- Introduction
- Attaching SIM and Description about Power-On and -Off
- Voice monitoring and Recording
- Configure the device
- Platform Operations
- Precautions
- Troubleshooting
- Warranty Instructions and Service
- FCC warning
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LL301
LTE CAT1 ASSET GNSS TRACKER
User Manual
Version:V1.5
LL301 Lte Cat1 Asset Gnss Tracker
Read this manual carefully prior to use to ensure fast and correct operation of the product. No prior notice will be given for any changes made to the appearance, color, or accessories of the product.
Introduction
Features
Power saving Mode | Multi-GNSS positioning |
---|---|
Large-capacity battery | Remote listening |
Tamper alert | Cover removal alert |
IP65 protection | Bluetooth Configuration |
Specification
Communication system:
LL301E| LTE FDD : B1//B3/B7/B8/B20/B28
GSM: 900/1800MHz
---|---
LL301L| LTE FDD : B1/B2/B3/B4/B5/B7/B8/B28/B66
GSM: 850/900/1800/1900MHz
GNSS accuracy| <10m
Listening range| ≤5m
Battery| 10,000mAh/3.7V industrial-grade Li-Polymer battery
LEDs| 1Red (work status) and
4Blue (battery level)
Operating temperature| –20℃to +70℃
Dimensions (LxWxH)| 108x61x30mm
Packing List
Standard
Name| Unit| Qty| Remarks
Tracker| PCS| 1| /
User Manual Card| PCS| 1| /
Charging cable| PCS| 1| /
Bracket| PCS| 1| With 3M Tape
Note: Please check the received package against the packing list. The contents are subject to actual items. As the product is in constant upgrade, no prior notice will be sent to you for any update in this User Manual.
Appearance
GSM LED
Status | Meaning |
---|---|
Fast blink | GSM initializing/No GSM signal/ |
No SIM card
Slow blink| Logging in to platform
Solid on| Device in a call
Note: The GSM LED goes off 3 minutes later after the device is turned on. The GSM LED will light up by short pressing the power button of the device in the power-on state and go off after 60 seconds.
Power LED
Under voltage|
---|---
0–25%|
25-50%|
50-75%|
75-100%|
Note: The power LED goes off 3 minutes later after the device is turned on. The power LED will light up by short pressing the power button of the device in the power-on state and go off after 20 seconds.
Notes on Work Modes
- Timed mode: In this mode, the device uploads position fixes at a fixed interval, which is configured via the location service platform or mobile app specified by your dealer.
- Smart mode (default): In this mode, the device tracks the vehicle in real-time, records the trips of the vehicle, and can differentiate moving state from parking state. If the vehicle moves, the GPRS connection is persistent and the device will upload a position fix every 20 seconds. If the vehicle stops, the device will enter the sleep mode and no position fix will be uploaded.
- Long standby mode: The device will wake up at a certain configured interval to upload position fixes. After each upload is complete, the device will enter deep sleep and will not execute any remote query or set actions.
Tamper Alert
When the device is attached to a vehicle, the anti-tamper button will remain
press-down. If the device is detached, the anti-tamper button will spring
back, which will trigger the device to send out a tamper alert. In the long
standby mode, the device will enable tracking for 20 minutes after the alert
message is sent out. The tamper alert feature can be disabled by command.
Cover Removal Alert
When the front cover of the device is in place, the cover removal detection
switch will remain press-down. If the cover is opened, the switch will spring
back, which will trigger the device to send out a removal alert. In the long
standby mode, the device will enable the smart mode for 20 minutes after the
alert message is sent out. The removal alert can be disabled by command.
Attaching SIM and Description about Power-On and -Off
Tips:
- Activate GPRS and SMS services of the SIM card.
- Power off the device (battery switch to OFF) before attaching or detaching the SIM card.
Attaching the SIM Card
Remove the back cover by the notch, slide the battery switch to OFF, and
insert the SIM.
Power-On and -Off
Power-on: Press the power button for 3 seconds (prerequisite: the battery
switch is ON).
Power-off: Press the power button for 3 seconds.
Installing the Device
The device has a strong magnet built inside. It can attach to any
ferromagnetic material. The magnet makes the installation easy.
Or you can stick the 3M tapes on one side of the device bracket, and attach
the bracket to the target object, then put the device on the bracket.
Voice monitoring and Recording
When center number sends monitor command: MONITOR# to the device, the device
will reply “OK” and call the center number. After the call connected, the
terminal will enter monitor condition. The center number can hear the sound
around the device.
For more operation, please refer to the command list section.
Configure the device
Method 1:
Use your mobile phone to send commands to the device SIM card number by SMS,
please refer details of the commands in Commands list section.
Method 2:
-
Download and install the “Jimi loT Lab”app by the OR code.
For iOS 11 and above Only
https://apps.apple.com/cn/app/jimi-iot-lab/id1531066185 -
Make sure the Bluetooth is enabled on your iPhone, choose Connect on landing page.
-
After connected charger to the LL301, the device name will automatically show on the connect page, tap on it to connect. For more operation, please contact your dealer”
Platform Operations
After binding the device on the location service platform or mobile app designated by the dealer, you can monitor it, configure it, and do more to it via the platform or app.
Logging In to Service Platform
You can configure and control the device via the designated location service
platform.
Downloading Mobile App
You can download the mobile app via the URL provided by your dealer.
Precautions
Please use batteries and accessories specified by the manufacturer of the
device; otherwise, the warranty will become void.
The manufacturer of the device shall bear no warranty liabilities for any
damage resulted from the use of non-original accessories.
Do not soak the battery in water or expose it to fire. Do not bend or forcibly
open the battery.
Do not disassemble the battery as the device may be damaged if the disassembly
is done improperly by a non-professional.
Troubleshooting
When a problem arises, you can troubleshoot it by the following solution. If the problem persists, please don’t hesitate to contact your dealer or service provider.
Common Issues | Possible Causes | Solutions |
---|---|---|
Poor signal | The device is used in an area where radio waves is hard to reach. | |
such as near high-rise buildings or in a basement. | Try it in a place where |
satellite signals can be well received.
Power-on failure| No SIM| Insert a SIM.
Battery switch is not set to ON.| Slide the battery switch to ON.
| The battery is exhausted.| Charge the device.
Failed to access the network| The SIM card may be attached improperly.| Check
the SIM.
The metal side of the SIM card is stained.| Wipe it with a clean cloth.
The SIM is invalid.| Please contact your network service provider.
The device is out of service areas.| Try it in a service area.
The signal is extremely weak.| Try it in an area with strong signals.
Failed to query a location| The SIM is not activated with data service.|
Please contact your network service provider and activate the data service.
The device keeps replying with “No data found, please try again’.| Please
contact your dealer.
Warranty Instructions and Service
Special Statement
① No prior notice will be given if the product is upgraded due to
technological reasons.
② The appearance or color of the product is subject to the actual.
③ The warranty card applies to the services of repair, replacement, and refund
of the product with the following IMEI.
④ Please keep this warranty card and the original purchase receipt together in
a safe place, as these will be needed at time of services.
Warranty Terms
For damages not caused by human factors, this warranty lasts for 2 (two) years
(including one-year replacement service) from the date of the original
purchase. You can choose to pay for the repair services in any of the
following cases:
① The warranty card expires;
② No warranty card or valid proof of purchase;
③ The product, including its accessories, is not in the warranty period;
④ Damage caused by unauthorized repairs, crash, liquid spillage, incident,
accident, modifications, or incorrect voltage input; or the label, IMEI, or
counterfeit mark of the product is broken or scribbled;
⑤ Damages caused by installation or use not in accordance with the user
manual;
⑥ Damage caused by force majeure such as fire, flood, or lightning;
⑦ The device model is inconsistent with the warranty card or the warranty card
has been altered;
⑧ Other damages caused by force majeure.
Reminder
For vehicle trackers:
As of January 1, 2016, the warranty lasts for 2 (two) years for repair from
the date of purchase, including one year for replacement.
The specific terms are:
A full replacement, including accessories, if the product is found defective
during unpacking check;
If a defect occurs within one year after installation, then:
① Replace only the mainboard if the housing is intact and doesn’t affect
normal use; or
② Replace the housing and the mainboard if the housing is defective and
affects normal use (Please be noted that man-made damages will void the
replacement service for the housing).
Free repair services will be given to the product if a defect is found during
the second year under proper use.
FCC warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This equipment complies with RF radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>