Jimi IoT X3-MN Multifunctional Vehicle GPS Tracker User Manual

Jimi IoT X3-MN Multifunctional Vehicle GPS Tracker

This user manual has been specially designed to guide you through the functions and features of your GPS vehicle tracker.

Start Guide

Packaging

• GPS tracker
• Power cable
• Audio cable
• SOS cable
• MIC
• Relay
• User manual

Main Functions

• Real-time GPS+AGPS tracking
• Track by time interval or distance
• Remotely fuel/power cut-off
• Listen-in
• TTL
• Instant alerts for vibration, Overspeed, etc.
• External power supply cut-off alarm
• Two-way talk
• Door status detection
• Multiple analog & digital I/Os
• Battery charging protection

Specifications

Hot Start  <2s
Storage| 32Mb+32Mb
Battery| 450mAh
Location Accuracy

Operating Temperature

| <10 meters

-20’C-+70’C

Dimension| 80.9 ( L) ><55.8 ( W) x2J.4 ( H ) mm
Weight| 95g

My Device

Appearance

LED indicators

Wire Connection

Wire Definition

yellow

| OUT 1-| Negative output
B| White& ” d| OUT2+| Controllable positive output (power voltage), ‘<500mAcurrent
9| Yellow| Relav| Fuel/Power cutoff
10| Black| SOS-| SOS (Negative)
11

12

| White

Purple

| SOS+

ADC

| SOS(Positive)

Detect 0.3-30V voltage

13| Orange| ACC| ACC
14| Black| GNO| Ground
15| Rod| PW•| Power: 9-36V

Wiring diagram

Wiring Instruction

1. The standard power supply ranges from 9V to 36VDC. Please use the power cord manufactured by the original factory. Redline means positive side while black line means negative side. During installation, the negative side should connect to the ground, do not connect with other ground wires at the same time.

2. ACC line (orange) connects to vehicle’s ACC switch. detecting ignition on and off.

3. The device “soil and electricity control line (yellow) connects to relay’s 86 (thin yellow line of relay socket)
   Relay wiring Instruction
   Relay wiring way of oil pump open circuit: On each end of the wire is thin white line (85) and thin yellow line (86). Thin while line (85) connects to the positive side of battery (12V) while thin yellow line (86) connects to the device relay control. There is an oil pump in the vehicle. Cut off the positive line. The positive side Df oil pump connects to the dose-snd of relay.(Thick green line 87a), and the other side connects to relay’s common(green thick 30).
   Notice
   12V relay is standard. The device is suitable for vehicles with 12V battery. If the vehicle has 24V battery, then 24V relay is needed.

4. To monitor analog signals, the purple line (ADC) of extended port should be connected to the analog line.

5. To check status of car door. orange line (IN1) should be connected to where between the door light and door switch (See the diagram). 6.To find car remotely, please connect the yellow line (OUT1) of extended port to external relay.

Device Installation

Note:
The device should face up to the sky.
Metal thermal barrier or heating layer of the windshield affects the signal. Please change installation places to receive better signal.

Operation of device

Power on/ Power off
Power on: Once you Insert a valid SIM card and connect all the wires. turn on the device. Power LED will flash first. During signal searching process, GSM LED and GPS(blue) LED will flash. Once Blue GPS LED keeps steadily ON, it means the device has been located and it starts toworK
Power off: Just toggle off the power switch.
Notice:
When device is connected with external power. please turn on the battery switch. The battery will then connect with the device circuits and its built- in battery will be charged. If battery is OFF, battery can’t be charged. The device will be power off if no external power supply.

Main Functions

1. sos
   In emergent case, press SOS for 3 seconds to activate SOS alarm. Then the device will send SOS SMS to preset SOS numbers and then dial the numbers in a loop for 3 timss until the call is picked up. Alarm messages will also send to platform. (See command list 7-9)

2. Power cut-off alarm
   When the electricity supply of device is cut off, it will activate cut-off alarm.

3. Low battery alarm
   When battery is low, the device will activate low battery alarm. Device will send alert through SMS and ID the platform

4. Vibration alarm (default OFF)
   When vehicle vibrates for several times, the vibration alarm will be triggered. If ignition Keeps OFF for 3 minutes (ACC OFF), the device will send vibration alarm message immediately.(See command list 7-13)

5. Voice monitoring
   1 .When MIC is connected while speaker is not, use pre-set SOS number to dial the device, after 10 seconds, device enters into monitoring mode automatically. The caller can hear the voice inside the vehicle.
   Notice

6. Pre-set SOS number is necessary.
   Non-SOS number cannot activate this function.

7. SIM card of device must have caller ID sevice.

8. Two-way communication
   To activate this function, ensure that both MIC and speaker are connected well.
   Use pre-set SOS number to dial the device. after 10 seconds. device enters into two-way talk mode.

9. Displacement alarm(default OFF)
   Device will send movement alarm when vehicle moves out the pre-set distance (when ACC is off and GPS is fixed).

10. Oil/Electricity cut-off
    When vehicle is stolen, Dillelectricity cut-off command can be sent by platform, APP or SMS.
    Notice

11. Make sure ACC is correctly connected,

12. When ACC is OFF, command will be executed immediately.

13. WhenACC is ON, but GPS is notfixsd, command will be postponed.

14. When ACC is ON. GPS is fixed, command will be executed when vehicle speed is less than 20kmlh.
    If you want to cut off/restore oil by SMS command, you have to set a center number firstly. Only the center number can send the cut off/reslDre oil command to the device. (See command list 7-15)
    Notice
    1.Only the SOS number can be used to set center number.
    2.Only the SOS number oan be used to delete center number.
    3.There is only one center number can be set

15. Restore oil/electricity
    When alarm is all-clear, you can send restore oil/electricity command by platform, APP or SMS and restore vehicle power.
    (See command list7-16)

16. Restart device
    If GPRS is abnormal (device is offline}, user can send SMS command RESET# to restart the device. Device will reboot after 20 seconds after receiving the command.(See command list 7-17}

17. Door detection
    The device is able to detect door status It uploads car status tD platform and APP timely. Negative triggering is default. When car door’s status Is negative triggering, there Is no need to set. Instead, if car door status is positive triggering, the triggering way has to be modified. (Command:DOOR,1#). See 3.2 diagram-1 for wiring way. (See command list 7-18)
    Notice
    Negative triggering (default): when door is open, signal level of door is OV: when door is closed, signal level of door is power voltage. Positive triggering: when door is open, signal level of door is power voltage; when door is closed, signal level of door is OV.

18. Analog signal
    The device can measure car battery’s voltage and upload it to platform/APP in a fixed time based on your needs. Purple line (ADC} of device extended port can receive analog signal, like voltage of external device, analog temperature sensor and fuel sensor. Voltage range of analog input is 0-30Vdc. See 3.2 diagram for wiring way.
    (See command list 7-19)

19. Lithium battery charging protection
    Built-in battery won’t be charged when the temperature is over 50″C or less than -20′.
    As soon as the temperature is lower than 48 ‘C or above -18’. battery charging will be restored.

20. Controllable output
    The device supports high/low level output, which could be configured by commands based on needs.

Platform Operation

Get registered on the designated service platform by authorized dealer. then you can start the tracking service and settings.

1. APN & Server setting
   To ensure normal network operation, please confirm your APN and server setting before login.
   In most countries, APN could be automatically adapted to local mobile operators. If not, please send SMS to set the APN. username and password is required for APN. please add it into the command. (See command list 7-7)
   Confirm the server address and setting with distributors. If the server is
   incorrect, please send SMS to change.(See command list 7-8)

2. Login service platform
   Please begin the designated service platform to set and operate the device.

3. Download APP
   Please download and install the APP in the designated website, APP store or Google Play store.

Common Command List

Edit SMS command in the right column to the device SIM number to achieve respective function as below:

APN setting

| 1 APN,apnname# E.g: APN,internet#

2. APN ,apnname,user,pwd#

E.g:  APN,internet,CUENTE,AMENA#

8

|

Server setting

| SERVER.mode,domain/lP,port,0#

E.g. SERVER,1,www.ydpat.com,8011,0# SERVER,0,211.154. 135.113,8011,0#

model means set with domain name

mode Omeans set with ip address

9

|

SOS setting

| 1.Add SOS number:

SOS,A,number 1,number 2,number 3# 2.Delete subjected sequence of SOS

number·

SOS,D,number sequence 1,

number sequence 2, number sequence 3

E.g. SOS,D, 1,2,3#

3 Delete the SOS number. SOS,D,phone number#

4. Query SOS number: SOS#

 |  | TIMER,T1.T2#

T1 =5~18000 seconds ; ACC ON upload interval: default value: 10

T2=5~18000 seconds : ACC OFF upload

interval: default value: 10(when GPS is not sleeping)

10 GPS data upload
 | time Interval

11

12

|

GPS data upload distance interval

Delayed defense setting

| DISTANCE,D#

D=O,  50~10000 meter:

Distance interval : default value : 300, unit: meter;

DEFENSE,A#

A:1~60 minutes, set delayed defense, default value   10 minutes

---|---|---
13| Vibration alarm (default OFF)| 1, SENALM,ON#

2. SENALM.OFF#

14

|

Displacement alarm setting

(default OFF)

| 1. MOVING.ON,R.M#

R=100~1000; Displacement radius, unit: meter

M=0-2:  Alert way O:GPRS, 1:SMS+GPRS; 2: GPRS+SMS+CALL

E.g. MOVING,ON,200,2#

2. MOVING.OFF#

15

|

Set center number

| Set center number: CENTER.A.mobile number#

Delete center number: CENTER,D#

16

|

Power/oil control

| RELAY,A# A=0/1

O= restore petrol; 1=cut off petrol Default value 0

E.g. RELAY, 1#

17

|

Restart

| RESET#

Device restart 20 seconds after receiving this command

18

| Car door negative/ positive triggering setting| DOOR.A#

A=0/1; 0 negative triggering, 1 positive triggering;

default: 0

19

|

Analog upload setting

| UplDad analog data:ADT,ON,T#

T: upload interval; scope: 5 3600(second) Turn off analog upload: ADT, OFF#

default· OFF

20

| Find car by triggering light

and buzzer                – –

|

FIND#

Troubleshooting

If you are having trouble with your device, try these troubleshooting procedures before contacting a service professional.

‘

Poor signal

| The signal waves unable to transmit when using the GPS tracker in the places that have poor signal reception. such as: tall building around or basement.|

Using the GPS tracker in the places that have the good signal conditions.

Unable to boot

|

Low battery

|

Charge the device battery

Unable to connect to the network|

Poor signal

| Using the GPS tracker in the places that have good signal conditions.
Unable to locate| Signal shielded or Poor signal| Change the installation place
No power off alarm| Bui It-In battery Is off| Tuition
Fail to start the car| Power cutoff I ACC abnormal| Restore power/Check ACC
Car stops driving| Abnormal power supply| Connect the device negative electrode to constant power
Offline/ Indicators off| normal power supply/Indicators sleep| Check power supply/Press side key to activate indicators
No update of vehicle’s location|

No GPS positioning

| Test the device again/ Change installation place

Warranty instructions and service

1. The warranty is valid only when the warranty card is properly completed, and upon presentation of the proof of purchase consisting of original invoice indicating the date of purchase, model and serial No.of the product. We reserve the right to refuse warranty if this information has been removed or changed after the original purchase of the product from the dealer.
2. Our obligations are limited ID repair of the defect or replacement the defective part or at its discretion replacement of Iha product itself
3. Warranty repairs must be carried out by our Authorized Service Centre. Warranty cover will be void, even if a repair has been attempted by any unauthorized. service center.
4. Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty period.
5. The warranty is not applicable to cases other than defects in material, design and workmanship

Maintenance Record

Date

| Serviced by

I                                         I

---|---

Product Model

|

IMEI Number

|
Fault Descriptions|

Comments

|

FCC Warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of Dflhe FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfacemce by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• CDnsult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your bods

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>