Jimi IoT JC400 Series EdgeCam 2 User Manual

JC400 Series EdgeCam 2
User Manual

Please read this manual carefully prior ta use.
The content of this manual may change due to improvement in performance without prior notice.

Introduction

1.1 Packing List
Standard

Optional

1.3 Appearance and LEDs
1.3.1 Main Unit

1.3.2 Sub camera Options

Refer to the specifications and features of the product model you purchased. If you have any questions, please contact your supplier.

No SIM
Off| Device in sleep (ACC OFF)
Defense LED| Blue| Fast blink for 30s| Vibrating alert triggered
Blink every lOs| Defense on
Off| Defense off

1.4 Wirings

RS232
(ootion)| I/0| /| To peripherals, such as oil sensor, card reader, etc.
SOS| SOS| /| To the external SOS key
Camera (options)| Remote camera| /| Monitor the cabin
Battery| ExternaI battery| /| To provide 450mAh backup battery for the device to protect it against  power outage resulted from sudden power disconnection

Installation

Precautions:

1. This device is not suitable for battery electric vehicles (BEVs) and hybrid electric vehicles (HEVs).
2. Use accessories specified by the manufacturer only.
3. The standard supply for the device is DC9-30V, please use the original power cable and ensure that the positive and negative ends are correctly wired.
4. Remove 1he prot ective film on 1he remote camera prior to installation.
5. It is recommended to ask a distributor, a designated business, or an expert to do the installation and commissioning.

3.1 Preparation
Device check
Check visually whether the device is in good condition and w hither the relevant accessories are complete.
3.2 SIM Card Attachment
Ensure that t he device is ACC OFF before attaching a proper SIM card.

To attach and detach the SIM may damage t he contacts, please use the completed Micro SIM card instead. In addi1ion, the SIM should have data service activated and not  in arrears. 

3.3 TF Card Attachment
Ensure that the device is ACC OFF before attaching a proper TF card.

Note:

1. Use TF card in speed class 10 or higher and with a capacityof16GB or above.
2. The TF card is recommended to change every half a year to ensure the recording performance of the device.
3. Mount the tamper cover after the attachment. Fit the TF card in the correct slot.

3.4 Main Unit Installation

1. Connect the power cable of the device to B+, ACC, and GND of the fuse box on the vehicle. 1 is a reference position.

2. Route the power cable along the A pillar of the vehicle to the upper center of the front windshield. The red dashed line(2) in the figure is for reference.

3. Selec1 a proper installation position and wipe the position clean.
   Remove the protective film from the 3M tape of the mounting base and attach it to the position. Wait for 2 hours before proceeding to the nex1 step. See 3 for reference.

4. Mounted device to the base and connect its power cable correctly (see 4 for reference). Than fasten the cable securely.

3.5 Installation of Accessories
You can select a proper position to install the remote camera according to actual conditions.
3.5.1 Remote AHD Camera

1. Face the camera inward and install it to the windshield behind the rear-view mirror (as shown in O )or to the middle of the dashboard (as showing in 1). Wipe a s elected  position clean, remove the protective film from the 3M tape, and attach the device.
2. Use the supplied screwdriver to tighten the screw of the camera, so it keeps at the best angle. Connect the cables correctly and fasten them securely.

3.5.2 DMS Camera
This section Is dedicated to JC4000.
The DMS camera is mainly used for monitoring the driver. Fixate the camera at an angle about 30′ to the steering wheel directly facing the driver’s head, as the following figures how’s.

3.5.3 Other Accessories

1. External battery
   It is used ta power the device for a while after its main supply is cutoff.
   Connect the external battery to the corresponding interface on the device and place it in a proper position (such as O in the above figure).

2. SOS key
   It is used to seek help in emergencies. Connect the SOS key to the corresponding interface on t he device, remove the protective film from the 3M tape, and then attach  it to a proper position (such asf) in the above figure).

3. Relay
   It is used to cutoff the power and fuel of the vehicle remotely to force it to stop. Connect it to the corresponding interlace on the device and place it in a proper position,  such asity in the above figure. For wiring details, see 1.4.

4. RS232 (optional)
   It is used to connect to an external device for function expansion when a scenario requires a feature that cannot be offered by the device. 4 is a ref refence installation  position.

Note:

1. Choose proper accessories based on your actual needs.
2. Select a relay that goes perfectly with the battery of your vehicle.
3. It is recommended1o ask a distributor, a designated business, or an expert to do the installation and commissioning.

3.6 Commissioning

1. Check the LED:See1.3.3 for reference.
2. Check the camera: This camera works correctly if you can view the have video of the camera and switch between-n the two cameras after logging in to the platform. You can also manually adjust the camera according to your needs.

Platform Operations

4.1 Installation
4.1.1 Platform
Scan the QR code on the right with the browser of your mobile phone to download and install the app.

4.1.2 Calibration Tool for JC4000

Scan the QR coda on the left with the browser of your mobile phone to download and install the calibration tool.
Note:
This app is used for feature calibration of JC400D.
This calibration tool is only compatible with mobiles with Android OS.

4.2 Operation Gulden
Seen the QR code on the right with the browser of your mobile phone lo view relevant operations.

Others

5.1 Battery Safety

1. Use the original battery supplied by the manufacturer only. The use of any non-original accessories may damage the device, in which case the manufacturer will assume  no repair liabilities for such damages.
2. Avoid metal objects as they may cause short circuits on battery contacts.
3. Do not remove the cover of the battery.
4. Do not soak the battery in water or expose it to fire.
5. It is forbidden to use batteries t hat are deformed, discolored, spilled, or package-damaged. If such an exception, such as over­ temperature, deformation, discoloration,  spillage, etc., occurs during use, charging, or storage o f the battery, please stop using the device immediately and contact1he aftersales center for a replacement.
6. It is forbidden to dismantle, or modify, or charge (in any other method other than stated) the battery.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>