Q-TRAN Q-CAP Flexible Fixtures

INSTALLATION

VHB MOUNTING

1. Remove the backing from the adhesive and apply firm pressure to the bonding surface.
2. Peel off secondary backing.
3. Adhere to mounting surface.

WHITE SNUG CLIP

NOTE: White snug clip should be placed every 12″

INCLUDED HARDWARE

• 4×5/8″ Flat head screw

1. Mount white snug clip with provided flat head screw.
2. Align fixture to white snug clips matching distances.
3. Press fixture into white snug clips.

PVC MOUNT CLIP: Connects two seamless fixtures, with or without wire exit

MICRO5-PPS-2

Mounting Feed

1. Press both fixtures into PPS clip.
2. Snap fixture into mounted PPS channel When wire will exit into conduit do not install bracket.
3. Finished Assembly for seamless bottom feed mounting (S5/P5).

LOW PROFILE PVC MOUNT CLIP: Connects two seamless fixtures, with or without wire exit.

MICRO5-PPS-LP-2

Mounting Feed

1. Snap in 2″ channel
2. Press in fixtures
3. Finished assembly for end feed mounting (S1/P1).

PVC MOUNT CHANNEL: Support for the fixture

MICRO5-PPS-96 & MICRO5-PPS-FT

• 96″ (PPS-96) or custom length (PPS-FT)

Built in wire way

• The PPS-BRACKET allows you to create a wire way under the PPS channel without any screws interfering

Millwork install

1. The PPS-BRACKET can be field cuttable and cut to whatever length your application requires. The PPS-BRACKET can be installed as a full length of 96″, multiple smaller pieces, or end to end for longer seamless runs.
2. Using pre-drilled pilot holes screw the #6 flat head screws to mount the PPS-BRACKET (1 screw every 16″).
   • NOTE : For drywall applications mount directly into a stud.
3. Using pre-drilled pilot holes, use the #6 flat head screws to mount the PPS-BRACKET.
4. The PPS-96 or PPS-FT can be field cuttable and cut to whatever length your application requires. The PPS-96 or PPS-FT can be installed as a full length of 96″, multiple smaller pieces, or end to end for longer seamless runs.
5. To mount, pinch the upper half of the PPS-96 or PPS-FT while you pivot it around one side of the PPS-BRACKET and push-in until you hear it snap into place. The PPS-96 or PPS-FT flexes around the PPS-BRACKET to create a solid, and secure snap on connection.

LOW PROFILE PVC MOUNT CHANNEL: Support for the fixture

MICRO5-PPS-LP-96 & MICRO5-PPS-LP-FT

96″ (PPS-96) or custom length (PPS-FT)

1. The PPS-LP-96 or PPS-LP-FT can be field cuttable and cut to whatever length your application requires. The PPS-96 or PPS-FT can be installed as a full length of 96″, multiple smaller pieces, or end to end for longer seamless runs.

2. Drill holes (1 hole/screw every 16″) into the PPS-LP.

3. Using pre-drilled holes, use the #6 flat head screws to mount the PPS-LP.
   NOTE : For drywall applications mount directly into a stud.

4. Snap fixture into PPS-LP.

• 2021 Q-Tran Inc. All rights reserved
• 155 Hill St. Milford, CT 06460
• 203-367-8777
• sales@q-tran.com
• www.q-tran.com

References

• Your Name as Your Email | Hover Realnames
• LED Lighting Systems, Linear LED Lights, LED transformers | Q-Tran

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>