GRANBERG 105.3810 MIG Welding Gloves Instruction Manual
- June 8, 2024
- GRANBERG
Table of Contents
105.3810 MIG Welding Gloves
Instruction Manual
ART. 105.3810
2777 6 pairs
PPE Cat. III
SIZE 8/M (EN ISO 21420:2020)
105.3810 MIG Welding Gloves
The results are taken from the palm area of the gloves.
The protection level increases with performance class.
12477:2001+A1:2005 Type A: Protective gloves for welders.
1149-2:1997 Protective clothing – Electrostatic properties – Part 2, R:
0.895 x 10 Ω (palm).
This product is classed as Category III Personal Protective Equipment (PPE)
according to PPE Regulation (EU) 2016/425 and as retained in UK Law and
amened and has been shown to comply with this Regulation through the
Harmonized Standards and Designated Standards EN 388:2016+A1:2018, EN
407:2004, EN 12477:2001+A1:2005, EN 1149-2:1997 and EN ISO 21420:2020. PPE
CAT. III: Complex design PPE that protects against the risks that may cause
very serious injuries. Levels only refer to the palm of the hand.
Notified Body responsible for certification and Module B compliance:
Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of
Ireland.
Notified Body number : 2777
Notified Body responsible for ongoing conformity (Module C2):
Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of
Ireland.
Notified Body number: 2777
Approved Body responsible for UKCA Type Examination:
Name: SATRA Technology Centre Ltd.
Address: Wyndham Way, Telford Way, Kettering, Northamptonshire NN16 8SD,
United Kingdom.
Approved Body number: 0321
Approved Body responsible for UKCA ongoing conformity (Module C2):
Name: SATRA Technology Centre Ltd.
Address: Wyndham Way, Telford Way, Kettering, Northamptonshire NN16 8SD,
United Kingdom.
Approved Body number : 0321
Declaration of Conformity can be obtained from
www.granberg.no/search
| Glove size | M | L | XL | 2XL | 3XL |
|---|---|---|---|---|---|
| EN ISO 21420 size | 8 | 9 | 10 | 11 | 12 |
Wear the products of suitable sizes to provide optimal level of protection and
maximum grip. User must only choose the glove fitting the size of her/his
hand.
TIG and MIG Welding Gloves. Cut resistant Kozane® FR material and goatskin,
unlined. Provides exceptional comfort and extreme cut and puncture
resistance. 14 cm split leather cuff.
Storage/Transport: The gloves are first packed in plastic bags which are
subsequently packed in cardboard boxes for transport and storage. Granberg
recommends storing unused gloves in original packaging. Prevent direct
sunlight.
Maintenance/Cleaning: Both new and used gloves should be inspected before
use, and before putting them on to make sure that there is no damage to them.
If in doubt, discard the gloves and select a new pair. Leaving the gloves in a
contaminated condition may cause a deterioration of quality. Cleaning or
disinfecting the gloves may also negatively affect quality. The performance
characteristics of gloves that have been worn or cleaned/disinfected/laundered
may differ from the performance levels declared. Gloves can only be cleaned
with damp cloth, but it will not stop permeation processes.
Obsolescence: When stored as recommended, unused gloves will not suffer
any change in their mechanical properties for up to five years from the date
of manufacture. Service life depends on application and maintenance and cannot
be specified. It is the responsibility of the user to ascertain the
suitability of the gloves for the user’s tasks.
Donning/Doffing: Select the right size glove for your hand. Hold the
glove by the cuff with one hand. Align the glove thumb with your other hand
thumb and slide your hand into the glove, one finger into each finger. Pull
by the glove cuff and align fingers into the right position. Use the same
procedure for the other hand. If gloves are not contaminated, pull by the
fingertips to doff the gloves. If gloves are contaminated, hold the glove cuff
and pull toward the finger until the gloves come off.
Please note: Inspect the gloves for damage before use. The gloves shall
not be worn when there is a risk of entanglement with moving parts of
machines. Gloves meeting the requirement for resistance to puncture may not be
suitable for protection against sharply pointed objects such as hypodermic
needles. Gloves containing latex may cause allergic reactions in cases of
hypersensitivity to latex. Seek medical advice if applicable. None of the raw
materials used in glove, or process of manufacturing it, are known to be
harmful to the user. Do not expose to open flame. If the gloves become wet, do
not use them to handle hot objects. For multi-layer gloves, performance level
are applicable to the whole glove including all layers. There is no
standardized test method at present for detecting UV penetration of materials
for gloves but the current methods of construction of protective gloves for
welders do not normally allow penetration of UV radiation. When gloves are
intended to arc welding: these gloves do not provide protection against
electric shock, caused by defective equipment or live working, and the
electrical resistance is reduced if gloves are wet, dirty or soaked with
sweat, this could increase the risk. These gloves are intended to protect
hands in working environments in accordance with EN 388:2016 +A1:2018 , EN
407:200 EN 12477:2001+A1:2005 Type A, 4, EN 1149-2:1997, EN ISO 21420:2020 and
ANSI/ISEA 105-2016. It is the responsibility of the user to evaluate and
determine risks based on the intended application. The gloves should only be
used for applications declared suitable by the manufacturer. Risk should be
evaluated keeping in mind the protection levels and the harmonized standards
on which gloves are tested. The results of the tests should help in glove
selection, however it must be understood that actual conditions of use cannot
be simulated and it is the responsibility of the user, not the manufacturer,
to determine glove suitability to the intended use. Further information may be
obtained from manufacturer.
User Manual issue date: 21.07.2021
Granberg AS, Bjoavegen 1442, NO-5584 Bjoa,
NORWAY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>