FLASH F7300250 High Power Logo Projector User Manual

: June 4, 2024
: FLASH

Table of Contents

1. INTRODUCTION
2. SAFETY INFORMATION
3. PRODUCT INFORMATION
4. INSTALLATION
5. CONNECTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLASH F7300250 High Power Logo Projector User Manual

1. INTRODUCTION

THANK YOU FOR PURCHASING BIG LOGO PROJECTOR IP65 300W. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

2. SAFETY INFORMATION

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
Maximum ambient temperature is: 400C Don’t operate it where the temperature is higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light spot while the fixture is on.

WARNING!

3. PRODUCT INFORMATION

Light source: 1pcs 300W LED
Signal: DMX 512
Power consumption: 300W
Color: 8 Colours + White
Gobo: 6 Gobo + 1 (patern effect)
Zoom: Yes
Focus: Yes
DMX standard: DMX 512
Beam angle (min): 11
Beam angle (max): 60
IP Rating: IP65
Dimensions: H(46)xW(24)xD(54) cm
Dim. (box): H(34,5)xW(69)xD(41) cm
Weight (with case):18 kg (9kg)

4. INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment
must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

5. CONNECTION

The device is equipped with the following interfaces:

DMX (in/out): XLR 3(5)-pin socket
Power (in/out): power CON socket

5.1 Connecting DMX signal

The connection is performed using cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between
signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.

5.2 Voltage specification

5.3 Connecting power supply

The connection is performed using power cable with Power Con connector (included). The device must be operated by qualified personnel.

Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions.

5.5 Manual control

This interface is used to control the current lamp, and at the same time automatically enter the host state (do not receive DMX signal, send DMX signal to the bus to the slave).
The manual menu will display 8 channels according to the standard 8 channels set in the setup menu.