CLOSETMAID 10840 30 Inch Cabinet Instruction Manual

June 8, 2024
ClosetMaid

CLOSETMAID 10840 30 Inch Cabinet
CLOSETMAID 10840 30 Inch Cabinet

SAFETY PRECAUTIONS

BEFORE BEGINNING

  • Please read all instructions carefully.
  • Familiarize yourself with all parts (see “PARTS”) and check quantities.
  • Follow all safety precautions (see “SAFETY PRECAUTIONS”).

WARNING

  • CHOKING HAZARD FOR SMALL CHILDREN. This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur.

  • ALWAYS UNLOAD UNIT PRIOR TO MOVING THE UNIT.
    The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur.

  • DO NOT OVERLOAD UNIT. If any shelf, top, or bottom of unit bows or bends, it is overloaded. The shelf, top, or bottom could collapse and cause serious bodily injury and/ or damage to personal belongings. Evenly distribute loads.

  • DO NOT CLIMB OR STEP ON THE UNIT. The unit may become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur.

  • DO NOT USE THIS UNIT AS A TELEVISION STAND.
    Serious bodily injury and/or damage to personal belongings may occur.

  • DO NOT ATTEMPT TO MOUNT UNIT TO WALL WITHOUT AN ASSISTANT.

  • DO NOT MOUNT OR ATTACH ANYTHING TO THE SIDES, REAR, OR FRONT OF THE UNIT. This can create a force which can cause the unit to tip. Serious bodily injury and/or damage to personal belongings may occur.

  • DO NOT STACK UNITS. Stacking of units can cause an unsafe tip-over hazard which may cause serious bodily injury and/or damage to personal belongings.

  • DO NOT HANG THIS UNIT ON THE WALL. The product structure is not designed for wall hanging. Serious bodily injury, damage to personal belongings, and/or damage to the wall may occur.

  • FOLLOW PROPER SAFETY PROCEDURES WHEN USING POWER TOOLS AND LADDERS.

  • PROTECT YOUR WORK SURFACE DURING ASSEMBLY.
    This can prevent scratching or damage to table tops, wood floors, etc.

  • UNIT DOES NOT PROVIDE PROTECTION AGAINST ELECTRICAL SHOCK.

FOLLOW INSTRUCTIONS CAREFULLY

FOLLOW INSTRUCTIONS CAREFULLY Please do not return product to the retail store.
For product assistance and warranty information please call Consumer Affairs at 1-800-874-0008.

Manufacturer Warranty
Manufacturer will replace any missing or damaged part due to manufacturer defect for one year after purchase.

Please have proof of purchase for warranty claims.

  • Do not let any sharp objects touch or rub the surface of the product.
  • When assembling, do not let children play around the working area.
  • Please confirm all parts are correct before starting the assembly process.
  • DO NOT OVERTIGHTEN. USE CAUTION IF USING POWER TOOLS DIRECTLY ON UNIT. Power tools can overtighten screws and strip threads.

PARTS

Call 1-800-874-0008 for parts and service. For faster service, have the style number ready when calling.

TOOLS REQUIRED

  • 2 and #3 Phillips Screwdrivers

  • Level

  • Drill

  • 5/16 in. Masonry Drill Bit

  • Hammer

HARDWARE PROVIDED

  Name Qty.
AA ST6.3 x 12 mm. Screw
****

32 + 2

BB| Electrical Bushing
| 1
CC| Concrete Anchor
HARDWARE PROVIDED| 4
DD| ST4.8 x 57 mm. Pan Head Tapping Screw
HARDWARE PROVIDED| 4
EE| M5 Washer
| 4
FF| Door Key
| 2

PARTS

Call 1-800-874-0008 for parts and service. For faster service, have the style number ready when calling.

PRODUCT
PRODUCT

  Name Qty Part #   Name Qty Part #
A Left Side Panel 1 35832 G Adjustable Feet 4 20620
B Right Side Panel 1 35834 H Bottom Shelf 1 35836
C Back Panel 1 35835 I Inner Shelf 3 35837
D Top Panel 1 35830 J Left Door 1 35838
E Bottom Panel 1 35831 K Right Door 1 35839
F Door Frame 1 35840      
STEP 1 Attach side panels to back panel

Align both side panels (A & B) with the back panel (C) as shown.
Slide the metal tabs on the back panel (C) into the matching slots on the side panels (A & B). Pull the side panels down to secure the tabs in place.
Attach side panels to back panel

STEP 2 Attach top panel

Align top panel (D) with the top of the unit as shown.
Push in to secure into place. Make sure that all the triangular tabs on the back and side panels completely snap into place in the square holes on the top panel.
Attach top panel

STEP 3 Attach bottom panel

Align bottom panel (E) with the bottom of the unit as shown.
Push in to secure into place. Make sure that all the triangular tabs on the back and side panels completely snap into place in the square holes on the bottom panel.
STEP 3 Attach bottom panel

STEP 4 Attach door frame

Align the door frame (F) with the front of the unit as shown. Please note that the holes on the bottom of the door frame will match up with the upper holes on the bottom panel.

Use a #3 Phillips screwdriver to secure the door frame to the unit using sixteen ST6.3 x 12 mm. screws (AA).
STEP 4 Attach door frame

STEP 5 Attach adjustable feet

Align the four adjustable feet (G) with the holes on the bottom panel. Use a

3 Phillips screwdriver to secure the feet to the unit using sixteen ST6.3 x

12 mm. screws (AA).
STEP 5 Attach adjustable feet

STEP 6 Attach electrical bushing

Stand the unit up on the feet.
Align the electrical bushing (BB) with the large circle on the back of the unit. Push in to secure
STEP 6 Attach electrical bushing

STEP 7a Secure unit via concrete mounting

Please use an assistant to help hold the unit during the mounting process to avoid possible tip over.

Align the unit with the location on the wall where you plan to mount it. Ensure unit is level and change adjustable feet height if necessary. Have an assistant hold the unit, locate the four large circles on the back panel, and use a pencil to mark their locations on the wall. Rotate unit away from wall and carefully drill a 5/16 in. hole that is 2-1/2 in. deep at the marked locations. Insert the four anchors (CC) in the wall and tap flush with a hammer. Rotate unit back to wall, make sure holes align with anchors, and use a #2 Phillips screwdriver to secure the four ST4.8 x 57 mm. pan head tapping screws (DD) and four M5 washers (EE) through the four holes in the back panel into the anchors.
STEP 7a Secure unit via concrete mounting

STEP 7b Secure unit via stud mounting.

Please use an assistant to help hold the unit during the mounting process to avoid possible tip over.

Locate studs and align the unit with the location on the wall where you plan to mount it. Ensure unit is level and change adjustable feet height if necessary. Have an assistant hold the unit, locate the four large circles on the back panel, and use a pencil to mark their locations on the wall. Use a #2 Phillips screwdriver to secure unit to wall by attaching the four ST4.8 x 57 mm. pan head tapping screws (DD) and four M5 washers (EE) through the four holes in the back panel into the studs.

NOTE: All four screws MUST be attached to studs for unit to be completely secured to wall. If any screws cannot connect to a stud, proceed to step 7c to secure.
STEP 7b Secure unit via stud mounting

STEP 7c Secure unit via drywall mounting.

Please use an assistant to help hold the unit during the mounting process to avoid possible tip over.

Please note that this mounting option requires separate hardware not included with this product. The ClosetMaid drywall mounting package (SKU: 2062800) is recommended for a secure fit.

Align the unit with the location on the wall where you plan to mount it. Ensure unit is level and change adjustable feet height if necessary. Have an assistant hold the unit, locate the four large circles on the back panel, and use a pencil to mark their locations on the wall. Rotate unit away from wall and carefully drill a 1/2 in. hole into the drywall at each marked location where you are inserting a toggle. Insert toggles into holes, pull tight against wall, zip plastic square pieces to wall, and snap long plastic pieces off to secure. Rotate the unit back to the wall, make sure holes align with toggles, and use a #2 Phillips screwdriver to secure the four fasteners and four M5 washers (EE) through the four holes in the back panel into the placed toggles.
STEP 7c Secure unit via drywall mounting

STEP 8 Attach shelves

Place the bottom shelf (H) inside the unit at the bottom. Push down to secure into place, making sure all metal tabs are connected. Please note that the bottom shelf is larger than the inner shelves and will rest on the lowest three metal tabs on the back panel.

Determine where you want to position the inner shelves (I). Place one inner shelf above the tabs on the inner side tracks of the unit and push down to secure, making sure all metal tabs are connected. We recommend you only place one shelf at a time, starting from the bottom and working up.
STEP 8 Attach shelves

STEP 9 Attach doors

Align the right door (K) with the right side of the unit. Place the bottom lock of the door in the hole on the bottom of the door frame. Pull the top lock down, align it with the hole on the top of the door frame, and push up to lock into place. Push the bottom lock down to completely secure the door. Make sure both locks are turned inward toward the door as shown below. Please note that the right door has the slot for the key lock.

Repeat steps for the left door (J) on the left side of the unit.
Double check that all locks are in position and secure.
STEP 9 Attach doors

CLOSETMAID

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ClosetMaid User Manuals

Related Manuals