BOCCI Stem Column 84.3V Floor Lamp Owner’s Manual
- June 8, 2024
- BOCCI
Table of Contents
BOCCI Stem Column 84.3V Floor Lamp
Dimension
Specification
- PENDANTS: three
- LAMPING: 1.5w LED
- POLE LENGTH 2.4m (8’) / 2.7m (9’) /3m (10’)
- MATERIALS: blown glass, black flexible cord, brass dial control, unlacquered brass or black powder-coated stem
- ADDITIONAL EXTENDERS 153mm (6”) / 305mm (12”)
- WEIGHT: approximately 9kg (19.8lb) / 9.4kg (20.7lb) / 9.7kg (21.5lb)
- CABLE LENGTH 2290mm (90”) flexible cable
- POWER SUPPLIES: Integral
DESCRIPTION
The stem column system comes in unlacquered brass or black powder-coated stem. It comes with a 2290mm (90”) long flexible cable with dial control for on/off/dimming. There is a notch on the back of the dial control for wall mounting.
A white glass bubble is captured inside a fine copper mesh basket and then plunged into hot clear glass. Air is blown into the matrix to gently push the white glass through the mesh, creating a delicate pillowed form that is suspended inside the thick outer layer of clear glass. Sometimes the copper mesh basket folds and crinkles, adding specificity to each piece.
NOTES
- Purchase replacement lamps online at www.bocci.com/shop/bulbs
- Details on minimum/maximum height, please see the column configurations diagram on the last page of this document.
- The brass used in our Stem Series is untreated and, as such, will develop a natural patina over time. To avoid any marking or tarnish on the brass during handling and installation, please use the gloves provided in your shipment.
- To maintain your fixture, please regularly dust it with a lint-free cloth. If further cleaning is required, dampen a lint-free cloth with water only and wipe gently to remove dust or debris.
Installation Instructions
- Thread the stem spikes onto the assembled stem on both ends. Connect the rest of the pieces with the stem connector.
- Note: This step is only necessary for 2.7m (9’) and 3m (10’) stem options.
- Note: Bocci recommends wearing thin gloves during installation to protect the stem finish and the glass surface.
- Thread the pendant mounting plate onto the stem. Carefully insert the provided lamp into the socket.
- Plug in the cord to the plug head. Plug-in light. Turn the dial to check power to the lamp is working correctly.
- Gently thread the pendant onto the stem. Be sure to carefully place the pendant so as not to damage the lamp during installation. Clean fingerprints.
- There are 2 x stem holders. Install one to the ceiling and one to the floor. You must secure the ceiling stem holder with provided screws.
- Peel off the adhesive silicone pad and attach it to the holder base.
- Position the stem holder to the ceiling and secure it with screws.
- Repeat the steps for the floor stem holder. Bocci recommends securing the floor stem holder to the floor for additional support.
- The end opposite to the cord has a spring-loaded spike. Unthread the spike to add or remove springs to adjust tension or range to the fixture.
- Push this end into the stem holder. The spike must rest inside the indentation.
Position the opposite end to the stem holder that is located on the floor.
Clean fingerprints from fixture surfaces.
BRASS COLUMN
This diagram is meant to illustrate the extender combinations for the columnar stem fixtures.
BLACK COLUMN
This diagram is meant to illustrate the extender combinations for the columnar stem fixtures.
For additional assistance, please contact Bocci:
sales@bocci.com
www.bocci.com
europe@bocci.com
www.bocci.com
US Patent Pending
EU Patent # 003611144-0001 to 0004
Made in Vancouver, Canada.
© 2021, Bocci Design and Manufacturing Inc. All rights reserved. Any inquiries should be directed to: info@bocci.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>