Outwell 650665 Wind Gust Tent Pump Instruction Manual

: June 8, 2024
: Outwell

Table of Contents

WIND GUST TENT PUMP 12V
- MODEL: 650665 / HB-630A
- INSTRUCTION MANUAL
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WIND GUST TENT PUMP 12V

MODEL: 650665 / HB-630A

Outwell 650665 Wind Gust Tent Pump

INNOVATIVE FAMILY CAMPING

INSTRUCTION MANUAL

WIND GUST TENT PUMP 12V

Read this manual before using the product.
Keep the manual for future reference.

Outwell 650665 Wind Gust Tent Pump A02

Pump unit
Control panel
12V cord
12V cigarette lighter plug
Fuse located in plug tip
Air hose
Air valve adaptor
Display
On/off button
Unit button
+ button
– button

WARNINGS

2. This pump is intended to inflate items such as tents, SUP boards etc. It’s not designed for use exceeding 20 minutes. Extended operation can overheat and damage the pump.

3. Do not exceed 20 minutes of continuous operation.
Take a 10 minute break before assuming inflation.

4. Carefully follow the instructions on the item you are inflating. Never exceed the recommended pressures. Bursting items can cause serious injury.
5. Never leave the air pump unattended while in use.
6. CAUTION: To reduce the risk of electric shock, do not expose the air pump to rain and store it indoors. Do not use the air pump under wet conditions.
Do not drop pump into water or other liquids. Do not operate the pump with wet hands.
7. Never allow sand, small rocks, etc. to be sucked into the inflation or air intake port while in use.
8. Never look into or point the inflate opening toward your eyes while pump is operating.
9. Never place your hand or fingers into the inflation or air intake opening at any time.
10. Never attempt to disassemble or close the openings while the air pump is operating.
11. The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped.
12. This appliance can be used by children from the age of 8 and people with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
13. Do not modify the product.

ASSEMBLY AND USE OF THE PUMP

Connect the air hose (6) to the pump unit (1).
Connect the cigarette lighter plug (4) to a suitable 12V DC outlet. The display (8) will now become activated.
Select a suitable nozzle (7) and attach it to the air hose (6) and to the valve on the inflatable device. Pay special attention to warnings #2 – #4.
Select the desired air pressure unit using the unit button (10).
Select the desired air pressure using the “+” and “-“ buttons (11) & (12).
Press the on/off button (9). The pump will now start, and the display will read 0.0 As the pressure in the inflatable device increases the display will read the current pressure in the inflatable device. When the pressure reaches the value selected in point #4, the pump will automatically stop.
Remove the air hose from the inflatable device and close the valve of the inflatable device.
Disconnect and disassemble the pump. Store it according to the warnings section.
To turn off pump during operation, press the on/off button (9).

Maintenance:

The pump can be cleaned with a damp rag. Allow the pump to dry completely before using it again.
Do not use corrosive liquids to clean the pump.
There is a fuse located in the tip of the 12V cigarette lighter plug (4).

To change the fuse:
Unthread the collar (1) and remove the collar and the tip (2) from the plug.
Remove and replace the fuse (3). The fuse must be replaced with a fuse of the same type, and with the same rating: 15A
Reposition the tip (2) and collar (3).
Rethread the collar (3), take care not to cross thread. Hand tighten only.

Instruction for disassembly of pump for disposal of components when pump has reached the end of its usable life:

Remove the air hose (6) and air valve adaptors (7). Dispose of these as plastic according to local regulations
Dispose of pump unit, cord and 12V plug cord as electric waste according to local regulations