erica synths Black Stereo Reverb Eurorack Module Instruction Manual
- June 13, 2024
- erica synths
Table of Contents
erica synths Black Stereo Reverb Eurorack Module
Product Information
The Erica Synths Black Reverb is a high-end module in the Black Series. It offers unique functionality and superior quality. The module is designed with usability in mind, featuring big knobs assigned to functions that make differences in the sound. It is built with the best, highest quality components and all inputs and outputs are protected against overvoltage. The Black Reverb is part of a range of modules that can be used to build an entire synthesizer. The reverb effect is based on Tape, BBD (Bucket Brigade Device), and digital delay lines.
It offers three room sizes, manual and triggered FREEZE with 1V/oct tracking, and 10 preset patches. The size, feedback, tone, dry/wet mix, and preset selection can be controlled via CV inputs. The module also provides adjustable stereo spin. It runs on Erica Synths DSP hardware and the effects are developed in collaboration with Dutch company 112.dB, known for their beautiful sounding effects.
Product Usage Instructions
- Connect your audio source to the L (MONO) IN or patch a mono signal into it. The signal will be automatically routed to the R input.
- If desired, connect a CV signal to the SIZE CV input to modulate the reverb size. The CV input is calibrated to track 1V/oct.
- Adjust the SIZE knob to set the reverb size.
- Use the TYPE switch to select the desired reverb type: Tape (T), BBD (B), or digital delay (D).
- If desired, connect a CV signal to the TONE CV input to modulate the reverb tone.
- Adjust the TONE/SPN knob to set the reverb tone or stereo spin (depending on the selected reverb type).
- If desired, connect a CV signal to the FEEDBACK CV input to modulate the reverb feedback.
- Adjust the FEEDBACK knob to set the reverb feedback level.
- If desired, connect a CV signal to the FREEZE SAVE input to control the freeze feature.
- Use the FREEZE button to initiate freeze with a gate or trigger signal. Use a second gate or trigger signal to unfreeze the audio buffer.
- Adjust the DRY/WET knob to set the balance between the dry and wet (effected) signal.
- Connect the L OUT and R OUT audio outputs to your audio system or mixer.
Firmware Update
- Download the firmware update audio file to your computer.
- Turn off your Eurorack system and connect the audio output (headphones out or soundcard output) to the L(MONO) IN of the Black Stereo Reverb module. Set the TYPE switch to the D position (lowest).
- Push and hold the SHIFT and FREEZE buttons simultaneously, then turn on the Eurorack system. The five LEDs on the right-hand side will start blinking, indicating that the firmware update mode is active.
Safety Instructions Please follow these safety instructions to ensure proper operation of the Erica Synths Black Reverb module:
- Avoid using the module in a humid or wet environment. It is not waterproof, and liquids or conducting substances should not get into the module. If this happens, disconnect the module from power immediately and have it examined and cleaned by a qualified technician.
THANK YOU
THANK YOU FOR PURCHASING THIS FRICA SYNTHS BLACK SERIES MODULE!
The Erica Black Series includes high-end, unique functionality and superior quality modules. Only the best, highest quality components are used, all inputs and outputs are protected against undesired overvoltage. When designing the Black Series, we prioritized usability. Big knobs are assigned to functions that make differences in the sound. The Black series consists of a range of modules that are needed to put together an entire synth. Enjoy!
The Erica Synths Black Reverb is a versatile hi-fi stereo FX module with lots of unique features based on our custom DSP engine. The reverb sources are selectable Tape, BBD and “dirty BBD” digital; emulations with three modes, each – Room, Hall and Cathedral. Delicate room size control, feedback, feedback tone and stereo spin controls allow for designing extremely delicate reverberation effects. CV control over various parameters and the ability to save up to 10 presets will make this module an integral part of any performance rack. The modules run on new Erica Synths DS hardware and the effects are developed in collaboration with Dutch company 112.dB who make some of the most beautiful sounding effects.
Product Overview
FEATURES
- Reverb based on Tape, BBD and digital delay lines
- Three room sizes
- Manual and triggered FREEZE with 1V/oct tracking
- 10 preset patches
- CV control over size, feedback, tone, dry/wet mix and preset selection
- Adjustable stereo spin
SPECS
- Max audio input level before clipping: 16Vptp
- CV input range (full span): -5V – +5V
- Sampling frequency: 48kHz, 24bit
- Audio codecs: -108 dynamic range,
- -98dB THD+N
- Power consumption: 120mA@+12V, 39mA@-12V
- Module width: 12HP
- Module depth: 35mm
FIRMWARE UPDATE
The Black Stereo Reverb module features an audio bootloader for firmware updates. In order to update the firmware:
- Download the audio file to your computer.
- Turn off your Eurorack system and connect the audio output (headphones out or audio output from a soundcard) to the L(MONO) IN of the Black Stereo Reverb module. Set the TYPE switch to the D position (lowest).
- Push and hold the SHIFT and FREEZE buttons simultaneously and turn the Eurorack system on. The five LEDs on the right-hand side will start blinking, indicating that the firmware update mode is active.
- Now, play the audio file from your computer. The left five LEDs will indicate the audio level of the incoming firmware file. At least 3 LEDs have to be illuminated for a sufficient audio level. If less than 3 LEDs are active, flip the TYPE switch to the B position to increase the audio level of the incoming signal.
- The firmware update will take few minutes. During the firmware update a blinking FREEZE button indicates that the update is going well, a blinking SHIFT button indicates an error. In case of an error, retry the update from step 1.
- Once the update is completed, restart your rack.
SAFETY INSTRUCTIONS
Please follow the instructions for use of the Erica Synths module below, ‘cause only this will guarantee proper operation of the module and ensure warranty from Erica Synths.
- Water is lethal for most of electric devices, unless they are made waterproof. This Erica Synths module is NOT intended for use in a humid or wet environment. No liquids or other conducting substances must get into the module. Should this happen, the module should be disconnected from mains power immediately, dried, examined and cleaned by a qualified technician.
- Do not expose the module to temperatures above +50° C or below -20° C. If you have transported module in extreme low temperatures, leave it in room temperature for an hour before plugging it in.
- Transport the instrument carefully, never let it drop or fall over. Warranty does not apply to modules with visual damages.
- The module has to be shipped in the original packaging only. Any module shipped to us for return, exchange and/or warranty repair has to be in its original packaging. All other deliveries will be rejected and returned to you. Make sure you keep the original packaging and technical documentation.
- This device complies to the EU guidelines and is manufactured RoHS conforming without use of lead, mercury, cadmium and chrome. Nevertheless, this device is special waste and disposal in household waste is not recommended.
More Information
User manual by Girts Ozolins@Erica Synths.
Design by Ineta Briede@Black8.
Copying, distribution or any commercial use in any way is prohibited and needs the written permission by Erica Synths. Specifications are subject to change without notice.In case of any questions, feel free to contact us through www.ericasynths.lv.
You will find Erica Synths terms of warranty at
www.ericasynths.lv
Items for return, exchange, and/or warranty repair have to be registered at
SUPPORT on www.ericasynths.lv and send back to us
according to instructions in the support page.