aigostar 330100NFR Mechanical Stand Fan Instruction Manual

Instruction Manual
Mechanical Stand Fan

MODEL 330100JTP
MODEL  33010ONFR

PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING THIS APPLIANCE AND RETAIN IT FOR FUTURE REFERENCE

IMPORTANT SAFETY INSTRUCTIONS

1. Use the fan only for the purposes described in this instruction manual.
2. To protect against electric shock, do not immerse the fan, its plug, or its cord in water or any other liquid or spray it with liquid.
3. Close supervision is necessary when the fan is being used by or near children or near pets.
4. Unplug the fan from the electrical outlet when not in use, when moving it from one location to another, before putting on or taking off parts, and before cleaning.
5. Avoid contact with any moving parts.
6. Do not operate the fan if it has a damaged cord or plug, if it has malfunctioned or if it has been dropped or damaged in any manner.
7. The use of attachments not recommended or sold by the appliance manufacturer may cause hazards
8. Do not use the fan outdoors.
9. To disconnect the fan from the electrical supply, grip the plug and pull it from the wall outlet. DO NOT pull on the cord.
10. Always use the fan on a dry, level surface.
11. 1f the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
12. This fan is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or who lack experience or knowledge unless they have been given supervision or instruction concerning its use by a person responsible for their safety.
13. Children should be supervised to ensure that they do not play with the fan.

TECHNICAL SPECIFICATIONS

The specifications and design are subject o changes without notice.

PRODUCT OVERVIEW

ASSEMBLY INSTRUCTIONS

BASE AND MOTOR

1. Loosen the 4 screws pre-fitted into the sand washer. Overlap the two brackets at the slot. Then, assemble the stand onto the X-base using the original screws. (Fig. 1)
   

2. Unscrew the height adjustment ring to loosen it, then slide down the screw cover. Lift the internal pole to the max. height while preventing the internal pole from slipping into the extension pole. Then, reattach the height adjustment ring and tighten it. (Fig. 2)
   Note: Loosen the height adjustment ring to adjust the internal pole to the desired height. (Note: If you cannot find the internal pole, it has slid inside the extension pole; pull it out from inside the extension pole.)

3. To attach the head unit to the internal pole, loosen the thumb screw at the bottom of the head unit. Place the head unit onto the internal pole and tighten the thumb screw. (Fig. 3)

GUARD AND FAN BLADES

1. Unscrew the spinner and guard mounting nut and remove them. Attach the rear guard to the motor, and make sure the handle is on the top. Then tighten the nut clockwise again. (Fig. 4)
   

2. Mount the blade onto the shaft. Make sure that the rotor shaft pin fits into the groove of the blades. Turn the spinner anticlockwise to tighten the blades. (Fig. 5)

3. Align the front guard hook to the rear guard. Fasten the front guard to the rear guard using the guard clip. Then, tighten the fan guard by locking the screw and nut (Fig. 6)

OPERATING INSTRUCTIONS

1. Set the fan on a dry, level surface.
2. Plug the power cord into any standard 220-240V- AC power outlet.
3. Adjust the speed using the speed switches.
   0| OFF
   ---|---
   1| Low speed
   2| Middle speed
   3| High speed
4. To start the oscillation of the fan head, push the oscillating knob down. Pull the oscillating knob up to stop the fan head from oscillating.
5. Tilt Control: The airflow can be adjusted upward or downward by tilting the fan head manually as desired.

CLEANING AND MAINTENANCE

1. Always unplug the fan before cleaning, assembly, or disassembly.
2. Do not allow water to drip on or into the fan motor housing.
3. Use a soft cloth moistened with a mild soap solution to clean the fan.
4. Do not use petrol, thinners, or benzene as a cleaner.

DISPOSAL

As a responsible retailer, we care about the environment. As such, we urge you to follow the correct disposal procedures for the appliance and its packaging materials. This will help conserve natural resources and ensure that these items are recycled in a manner that protects the health and the environment. You must dispose of the appliance and its packaging according to local laws and regulations. As this appliance contains electronic components, it and its accessories must be disposed of separately from household waste when the appliance reaches the end of its life. Contact your local authority to learn about your disposal and recycling options. The appliance should be taken to your local recycling center. Some collection points accept appliances free of charge.
WARRANTY: 2 YEARS

https://www.aigostar.com/ES/turnto/turnto3.aspx

ITALIA MARKET SRL
VIA DELLE INDUSTRIE, 9/1 20883 MEZZAGO(MB), ITALIA
P.IVA: IT10502730962

http://WWW.AIGOSTAR.COM
MADE IN P.R.0

Documents / Resources

| aigostar 330100NFR Mechanical Stand Fan [pdf] Instruction Manual
330100NFR, Mechanical Stand Fan, 330100NFR Mechanical Stand Fan, Stand Fan, Fan
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>