PPE 158207000 Heavy-Duty Forged Tie Rod Installation Guide
- June 8, 2024
- PPE
Table of Contents
PPE 158207000 Heavy-Duty Forged Tie Rod
Installation Guide
CONTENTS:
- (2) Heavy-Duty Forged Tie Rod Assemblies
Heavy-Duty Forged Tie Rod Assemblies
INSTALLATION
-
Step 1. Vehicle off and in Park with Parking Brake applied on a level surface. Jack up the vehicle and secure. Remove front tires.
REMOVAL -
Step 2. PASSENGER SIDE OUTER TIE ROD – Remove nut at the end of the stock spindle. Tap the spindle on the end surface with a hammer to release from the knuckle.
-
Step 3. PASSENGER SIDE INNER TIE ROD – Remove stock retainer clamp on the inner boot. Pull back the boot and unscrew inner tie rod to remove.
PREP: Loosen Jam Nut on PPE Tie Rods. Measure length of stock tie rods. Adjust PPE Tie Rods to the length of stock tie rods removed. Tighten Jam Nut to 55 ft lbs.
INSTALL
- Step 4. Apply “red thread locker” to the threaded inner. Install and tighten to 75-85 ft-lbs.
- Step 5. Install ball pin into steering knuckle. Tighten the Lock Nut to 45 ft-lbs.
- Step 6. Tighten Inner Boot Clamp.
- Step 7. Repeat install procedure on driver side.
- Step 8. Have vehicle professionally aligned.
This completes the installation.
DISCLAIMER OF LIABILITY
Performance products can increase horsepower above and beyond factory specifications. Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure. Note regarding emissions-related, non-E.O.-legal products:
THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE
products. The installation of this product indicates that the Buyer has read
and understands this agreement and accepts the terms and conditions. PPE
(Pacific Performance Engineering) Inc., its distributors, employees, and
dealers (the “Seller”) shall not be responsible for the product’s proper use
and service. The buyer hereby waives all liability claims. The Buyer hereby
acknowledges no reliance on the Seller’s skill or judgment to select or
furnish goods suitable for any particular purpose and that there are no
liabilities which extend beyond the description on the face hereof, and the
Buyer hereby waives all remedies or liabilities expressed or implied, arising
by law or otherwise (including without any obligation of the Seller with
respect to fitness, merchantability and consequential damages), or whether or
not occasioned by the Seller’s negligence.
The Seller disclaims any warranty and expressly disclaims any liability for
personal injury or damages. The Buyer acknowledges and agrees that the
disclaimer of any liability for personal injury is a material term for this
agreement and the Buyer agrees to indemnify the Seller and to hold the Seller
harmless from any claim related to the item of equipment purchased. Under no
circumstances will the Seller be liable for any damages or expenses by reason
of use or sale of any such equipment. The Seller assumes no liability
regarding the improper installation or misapplication of its products. It is
the installer’s responsibility to check for proper installation and if in
doubt, contact the manufacturer. The Buyer is solely responsible for all
warranty issues from the manufacturer.
LIMITATION OF WARRANTY
The Seller gives Limited Warranty as to description, quality, merchantability,
and fitness for a particular purpose, productiveness, or any other matter of
Seller’s product sold herewith. The Seller shall not be responsible for the
products proper use and service and the Buyer hereby waives all rights other
than those expressly written herein. This warranty shall not be extended,
altered or varied except by a written instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE
Transmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up-
Pipes Kits, and OEM-Length Up-Pipes. One (1) year limited warranty on all
other PPE products from the date of sale to original buyer and limited solely
to the parts contained within the products kit. All products that are in
question of Warranty must be returned prepaid to the Seller and must be
accompanied by a dated proof of purchase receipt. All Warranty claims are
subject to approval by Seller. Under no circumstances will the Seller be
liable for any labor charged or travel time incurred in diagnosis for defects,
removal, or re-installation – of this product or any other contingent
expenses. Under no circumstances will the Seller be liable for any damage or
expenses incurred by reason of the use or sale of any such equipment. In the
event that the buyer does not agree with this agreement: the buyer may
promptly return this product, in a new and unused condition in its original
packaging, with a dated proof of purchase to the place of purchase within ten
(10) days from date of purchase for a full refund. The installation of this
product indicates that the buyer has read and understands this agreement and
accepts its terms and conditions. PPEpower.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>