LANCOM XS-5116QF 16-Port 10-Gigabit Ethernet User Guide
- June 8, 2024
- LANCOM
Table of Contents
LANCOM XS-5116QF 16-Port 10-Gigabit Ethernet
OVERVIEW
-
Configuration interfaces RJ-45 & micro USB (Console)
Connect the configuration interface ➀ via the included serial configuration cable to the serial interface of the device you want to use for configuring/monitoring the switch. Alternatively use the interface -
with a suitable micro USB cable.
-
USB interface
Connect a USB stick to the USB interface to store general configuration scripts or debug data. You can also use this interface to upload new firmware. -
SFP+ interfaces 1G/10G
Insert suitable LANCOM SFP modules into the SFP+ interfaces 1 to 12. Choose cables that are compatible with the SFP modules and connect them as described in the SFP modules mounting instructions www.lancom-systems.com/SFP-module- MI. -
SFP+ interfaces 1G/10G (combo ports)
Insert suitable LANCOM SFP modules into the SFP+ interfaces 13 to 14. Choose cables that are compatible with the SFP modules and connect them as described in the SFP modules mounting instructions www.lancom-systems.com/SFP- module-MI. -
TP Ethernet interfaces 1G/2.5G/5G/10G (combo ports)
Connect interfaces 13 to 14 via Ethernet cables to your PC or a LAN switch. -
QSFP+ interfaces 40G
Plug suitable LANCOM QSFP+ modules into the QSFP+ interfaces 15 to 16. Select cables suitable for the QSFP+ modules and connect them as described in the SFP modules mounting instructions www.lancom-systems.com/SFP-module- MI. -
Power supply module with mains connection socket (rear panel).
Supply the device with power via the power supply socket of the power supply module. Use the supplied power cord or a country-specific LANCOM power cord. To remove the power supply module, disconnect the module from the power supply and then pull the plug out of the module. While pressing the release lever 11 to the left, you can pull the module out of the device by handle 10. -
An additional slot for power supply module with mains connection socket (rear panel).
To install an additional power supply module, remove the corresponding module bay cover by loosening both associated screws and push the power supply module in as far as it will go until the release lever 11 audibly engages. Check by pulling handle 10 that the module cannot be removed from the bay without the release lever 11 being pressed to the left.
Please observe the following when setting up the device
- The mains plug of the device must be freely accessible.
- Do not rest any objects on top of the device and do not stack multiple devices.
- Keep the ventilation slots of the device clear of obstruction.
- Mount the device with the enclosed rack mounting system in a free 19” slot of an appropriate server rack. Both slide-in rails are attached as shown in the accompanying installation instructions www.lancom-systems.com/slide-in-MI.
- Please note that support for third-party accessories (SFP and DAC) is not provided.
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide! Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
SPECIFICATION
- System / Fan / Stack
- system: green Device operational
- System: red Hardware error
- Fan: red Fan error
- Stack: off No connection
- Stack: green As master device: port activated and connected to slave device
- Stack: orange As slave device: port activated and connected to master device
- Reset button
- ~5 sec. pressed Device restart
- ~7-12 sec. pressed Configuration reset and device restart
- SFP+ ports 1G / 10 G
- Off Port inactive or disabled
- Green Link 10 Gbps
- Green, blinking Data transfer, link 10 Gbps
- Orange Link 1 Gbps
- Orange, blinking Data transfer, link 1 Gbps
- SFP+ ports 1G / 10G (combo ports)
- Off Port inactive or disabled
- Green Link 10 Gbps
- Green, blinking Data transfer, link 10 Gbps
- Orange Link 1 Gbps
- Orange, blinking Data transfer, link 1 Gbps
- TP Ethernet ports 1G / 2.5G / 5G / 10G (combo ports)
- Off Port inactive or disabed
- Green Link 10 / 5 / 2.5 Gbps
- Green, blinking Data transfer, link 10 / 5 / 2.5 Gbps
- Orange Link < 2.5 Gbps
- Orange, blinking Data transfer, link < 2.5 Gbps
- QSFP+ ports 40G
- Off Port inactive or disabled
- Green Link 40 Gbps
- Gren, blinking Data transfer, link 40 Gbps
- Power supply unit LED
- Off No primary voltage supply
- Green Secondary voltage supply OK
- Orange Critical power supply event that causes a shutdown: OCP, OVP, fan failure In case of parallel primary voltage supply by second power supply unit: power cable disconnected or power failure
- Orange, blinking Power supply warning event in which the power supply continues to operate: high temperature, high power, high current consumption, slow fan
Hardware
- Power supply Exchangeable power supply (110-230 V, 50-60 Hz)
- Power consumption max. 250 watts
- Environment Temperature range 0–40°C, humidity 10–90%; non-condensing
- Housing Robust metal housing, 19“ 1U (442 x 44 x 375 mm > W x H x D), network connectors on the front
- Number of fans 1
Interfaces
- QSFP+ 2 * QSFP+ 40 Gbps uplink ports for connection to higher-level core switches or content servers, also configurable as stacking ports via software
- SFP+ / TP-Ethernet Combo-Ports Each 2 * SFP+ (1 / 10 Gbps) / TP-Ethernet (1 / 2,5 / 5 / 10 Gbps) combo ports for use as additional downlink ports or for connection to a NAS or router
- SFP+ 12 * SFP+ 1 / 10 Gbps downlink ports for aggregation of subordinate access switches
- Console 1 RJ-45 / 1 Micro USB
- USB 1 * USB
Package Content
- Mounting material Rack mounting system consisting of 2 mounting brackets for front mounting and 2 slide-in rails for optional rear mounting of the switch in the rack.
- Power supply 1x exchangeable power supply LANCOM SPSU-250, expandable to 2 LANCOM SPSU-250 power supplies (hot swappable, for redundancy operation)
- Cables 1 IEC power cord, 1 serial configuration cable, 1 micro USB configuration cable
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc
LANCOM, LANCOM Systems, LCOS, LAN community and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>