perfect aire 3PAMSH09A-SZW Single-Zone Mini-Split Remote Control Owner’s Manual
- June 8, 2024
- Perfect Aire
Table of Contents
OWNER’S MANUAL
REMOTE CONTROL
SINGLE-ZONE MINI-SPLIT
MODELS: 3PAMSH09A-SZW, 3PAMSH09B-SZW, 3PAMSH12A-SZW,
3PAMSH12B-SZW, 3PAMSH18B-SZW, 3PAMSH24B-SZW
3PAMSH09A-SZW Single-Zone Mini-Split Remote Control
SPECIFICATIONS:
Remote Model | RG10A4(D1)/BGEFU1 |
---|---|
Indoor Unit Models | 3PAMSH09A-SZW, 3PAMSH09B-SZW, 3PAMSH12A-SZW, 3PAMSH12B- |
SZW, 3PAMSH18B-SZW, 3PAMSH24B-SZW
Rated Voltage| 3.0V (Dry batteries R03/LR03×2)
Signal Receiving Range| 24 ft. / 8 m
Environment| 23°F~140°F(-5°C~60°C)
IMPORTANT NOTE:
Read the manual carefully. Make sure to save this manual for future reference.
Illustrations in this manual are for explanatory purposes only, your actual
product may look slightly different.
WARNING: Cancer www.P65Warnings.ca.gov
QUICK START GUIDE
NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions
sections of this manual for a detailed description of how to use your air
conditioner.
SPECIAL NOTE:
- Button designs on your unit may differ slightly from the example shown.
- If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
- When there are wide differences between “Remote control Manual” and “USER’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.
HANDLING THE REMOTE CONTROL
INSERTING AND REPLACING BATTERIES
Your air conditioning unit may come with two AAA batteries. Put the batteries
in the remote control before use.
- Slide the back cover from the remote control downward, exposing the battery compartment.
- Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
- Slide the battery cover back into place.
BATTERY NOTES For optimum product performance:
- Do not mix old and new batteries, or batteries of different types.
- Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.
Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.
TIPS & REGULATIONS FOR USING REMOTE CONTROL
TIPS
- The remote control must be used within 24 Feet / 8 Meters of the unit.
- The unit will beep when remote signal is received.
- Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
- Remove batteries if the remote will not be used more than 2 months.
REGULATIONS
The device could comply with the local national regulations.
- In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
- In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
BUTTONS AND FUNCTIONS
Model: RG10A4(D1)/BGEFU1
NOTE: Press together ∧ & ∨ buttons at the same time for 3 seconds will
alternate the temperature display between the °F & °C scale. Fresh feature is
not available. AP Feature not available.
REMOTE SCREEN INDICATORS
NOTE: All indicators shown in the figure are for the purpose of clear presentation. But during the actual operation, only the relative function signs are shown on the display window.
HOW TO USE BASIC FUNCTIONS
ATTENTION:
Before operation, please ensure the unit is connected to a main source of
electricity and power is available.
SETTING TEMPERATURE
The operating temperature range for units is 62-86°F (17-30°C/20-28°C).
You can increase or decrease the set temperature in 1°F (1°C) increments.
AUTO MODE
In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT
operation based on the set temperature.
- Press the MODE button to select AUTO.
- Set your desired temperature using the TEMP ∧ or TEMP ∨ button.
- Press the ON/OFF button to start the unit.
NOTE: FAN SPEED can’t be set in AUTO mode.
HEAT MODE
- Press the MODE button to select HEAT mode.
- Set your desired temperature using the TEMP ∧ or TEMP ∨ button.
- Press FAN button to select the fan speed:
- AUTO, LOW, MED or HIGH
- Press the ON/OFF button to start the unit.
NOTE: As outdoor temperature drops, the performance of your unit’s HEAT function may be affected. In such instances, we recommend using this air conditioner in conjunction with other heating appliances.
DRY MODE (DEHUMIDIFYING)
- Press the MODE button to select DRY mode.
- Set your desired temperature using the TEMP ∧ or TEMP ∨ button.
- Press the ON/OFF button to start the unit.
NOTE: FAN SPEED can’t be changed in DRY mode.
COOL MODE
- Press the MODE button to select COOL mode.
- Set your desired temperature using the TEMP ∧ or TEMP ∨ button.
- Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH
- Press the ON/OFF button to start the unit.
FAN MODE
- Press the MODE button to select FAN mode.
- Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH.
- Press the ON/OFF button to start the unit.
NOTE: You can’t set temperature in FAN mode. As a result, your remote control’s LCD screen will not display temperature.
SETTING THE TIMER
TIMER ON/OFF – Set the amount of time after which the unit will automatically
turn on/off.
TIMER ON SETTING
Press TIMER button to initiate the ON time sequence.
Press Temp. up or down button for multiple times to set the desired time to
turn on the unit.
Point remote to unit and wait 1sec, the TIMER ON will be activated.
TIMER OFF SETTING
Press TIMER button to initiate the OFF time sequence.
Press Temp. up or down button for multiple times to set the desired time to
turn on the unit.
Point remote to unit and wait 1sec, the TIMER OFF will be activated.
TIMER ON & OFF SETTING (example)
Keep in mind that the time periods you set for both functions refer to hours
after the current time.
Example: If current timer is 1:00PM, to set the timer as above steps, the unit will turn on 2.5h later (3:30PM) and turn off at 6:00PM.
NOTE:
- When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
- Cancel either function by setting its timer to 0.0h.
HOW TO USE ADVANCED FUNCTIONS
LED DISPLAY
PRESS LED BUTTON to turn on and turn off the display on the indoor unit.| KEEP
PRESSING THIS BUTTON MORE THAN 5 SECONDS, the indoor unit will display the
actual room temperature. Press more than 5 seconds again will revert back to
display the setting temperature.
---|---
|
SWING
The horizontal louver will swing up and down automatically when PRESSING SWING
BUTTON.
Press again to make it stop.
KEEP PRESSING THIS BUTTON MORE THAN 2 SECONDS, the vertical louver swing function is activated.
TURBO
When you SELECT TURBO FEATURE IN COOL MODE, the unit will blow cool air with
strongest wind setting to jump-start the cooling process.
When you select TURBO FEATURE IN HEAT mode, for units with Electric heat
elements, the Electric HEATER will activate and jump-start the heating
process.
SHORTCUT
PRESS SHORTCUT BUTTON when remote control is on, the system will automatically
revert back to the previous settings including operating mode, setting
temperature, fan speed level and sleep feature (if activated).
IF PUSHING MORE THAN 2 SECONDS, the system will automatically restore the
current operation settings including operating mode, setting temperature, fan
speed level and sleep feature (if activated ).
SLEEP ( ):
THE SLEEP FUNCTION is used to decrease energy use while you sleep (and don t
need the same temperature settings to stay comfortable).
This function can only be activated via remote control. For the detail, see
“sleep operation” in “USER’S MANUAL”.
NOTE: The SLEEP function is not available in FAN or DRY mode.
FP
The unit will operate at high fan speed (while compressor on) with
temperature automatically set to 46°F/ 8°C.
Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.
SILENCE
KEEP PRESSING FAN BUTTON FOR MORE THAN 2 SECONDS to activate/disable Silence
function.
Due to low frequency operation of compressor, it may result in insufficient
cooling and heating capacity.
Press ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel
silence function.
SET
PRESS THE SET BUTTON to enter the function setting, then press SET button or
TEMP or TEMP button to select the desired function. The selected symbol will
flash on the display area, press the OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:
Fresh( ) → Sleep( ) → Follow Me( ) → AP mode( )
CLEAN
Airborne bacteria can grow in the moisture that condenses around heat exchanger in the unit. With regular use, most of this moisture is evaporated from the unit. By PRESSING THE CLEAN BUTTON, your unit will clean itself automatically. After cleaning, the unit will turn off automatically. Pressing the CLEAN button mid-cycle will cancel the operation and turn off the unit. You can use CLEAN as often as you like.
NOTE: You can only activate this function in COOL or DRY mode.
FOLLOW ME ( ):
The FOLLOW ME FUNCTION enables the remote control to measure the temperature
at its current location and send this signal to the air conditioner every 3
minutes interval.
NOTE: Remote be within a 24 ft./8 m unblocked signal receiving range to
communicate with indoor head.
When using AUTO, COOL or HEAT modes, measuring ambient temperature from the
remote control (instead of from the indoor unit itself) will enable the air
conditioner to optimize the temperature around you and ensure maximum comfort.
NOTE: Press and hold Turbo button for seven seconds to start/stop memory feature of Follow Me function.
- If the memory feature is activated, “ON” displays for 3 seconds on the screen.
- If the memory feature is stopped, “OFF” displays for 3 seconds on the screen.
- While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function.
LOCK
PRESS TOGETHER CLEAN AND TURBO BUTTON
at the same time more than 5 seconds to activate Lock function. All buttons
will not response except pressing these two buttons for two seconds again to
disable locking.
5401 Dansher Road
Countryside, IL 60525
844-4PA-AIRE | 844-472-2473 |
support@perfectaire.us
CANADA SUPPORT 877-997-2473 |
supportcanada@perfectaire.us
www.perfectaire.us
Printed in China | 0921_M857
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>