Benewake BP-UM-75-EN V00 TTL / CAN to USB Converter for TF LiDAR User Manual

June 8, 2024
Benewake

Benewake BP-UM-75-EN V00 TTL / CAN to USB Converter for TF LiDAR

INTRODUCTION

  • This USB TTL converter is a port-powered bi-directional USB to TTL/CMOS 5V converter, which can be used to convert any standard full-duplex USB port into a full-duplex TTL port and vice versa.
  • The unit is powered from the USB port and it supports data auto-sensing & self-adjusting, and therefore, no baud rate setting is required.
  • The unit uses the latest FTDI chipset and is fully compatible with Windows 11/10/7/Vista/XP (32- bit & 64-bit), Mac, and Linux.

FEATURES

  • Adds one TTL/CAN port to your USB port.
  • Supports 9,600 to 921,600 baud.
  • Supports Windows 11/10/7/Vista/XP (32-bit & 64-bit), Mac, and Linux.
  • Plug and play (hot-pluggable, data format auto-sensing and self-adjusting).
  • Port-powered, no external power required.
  • No IRQs required, no IRQ conflicts.
  • Supports all TF series LiDARs of Benewake.

SPECIFICATIONS

Compatibility USB 3.0 (backward compatible)
Power Source From USB port
Current Consumption Less than 200mA
Baud Rates 9,600 to 115,200bps
Connectors USB side: Mini-B

TTL side: Molex 53261-0471, Molex 53261-0771, Molex 53261-0271

Dimensions| 53.75mm 27.94mm 7.6mm (LWH)
Cable Length| 100cm
Operating Temperature| 0…50℃
Operating Humidity| Up to 90% RH (no condensation)

OVERVIEW

Benewake-BP-UM-75-EN-V00-TTL-CAN-to-USB-Converter-for-TF-LiDAR-
fig-2

  1. Indicators of CAN baud rate.
  2. Connector. Mini-B.
  3. Push button. Switch Baud rate of CAN.
  4. UART port. Connector for TFmini Plus / TFmini-S / TFLuna. Molex 53261-0471
  5. CAN port. Connector for TFmini Plus / TFmini-S / TFLuna. Molex 53261-0471
  6. UART / CAN port1. Connector for TF03 / TF350. Molex 53261-0771
  7. Connector. Molex 53261-0271
    This is a 7-Pin port, supports UART and CAN at the same time.

DIMENSIONS

Benewake-BP-UM-75-EN-V00-TTL-CAN-to-USB-Converter-for-TF-LiDAR-
fig-3

CONNECTIONS

Benewake-BP-UM-75-EN-V00-TTL-CAN-to-USB-Converter-for-TF-LiDAR-
fig-6

  1. Computer.
  2. Mini USB Cable, A-Male to Mini-B Cord USB 2.0 cable.
  3. Benewake TTL / CAN to USB converter.
  4. Benewake Single-Point LiDAR, TF03. Compatible with all TF Series LiDAR.
    Note: The TTL / CAN to USB converter will generate two COM ports once it is connected to computer. See Figure 4 COMs generated in Device Manager by TTL / CAN to USB converter. The COM port with
    small number is the UART port. The COM port with large number is the CAN port.

TROUBLE SHOOTING

Make sure that the TTL / CAN to USB converter is connected to your USB port, and the driver is installed correctly (as shown below); otherwise, please reinstall the driver (refer to CP210x USB to UART Bridge VCP Drivers – Silicon Labs (silabs.com)).

Benewake-BP-UM-75-EN-V00-TTL-CAN-to-USB-Converter-for-TF-LiDAR-
fig-5

ABOUT COMPANY

  • Benewake (Beijing) Co., Ltd
  • Address: Room 3030, Building ZiZhuChuangXin, No.6 Chuangye Road, Haidian District,
  • Beijing, PRC
  • Phone: +86 010 5745 6983
  • Email: bw@benewake.com
  • Technical support: support@benewake.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals