KIND LED XL1000 Wifi Indoor WiFi LED Grow Light User Guide
- June 6, 2024
- KIND LED
Table of Contents
XL1000 Wifi Indoor WiFi LED Grow Light
CONGRATULATIONS ON PURCHASING THE MOST ADVANCED LED GROW LIGHT IN
THE INDUSTRY, THE KIND LED X2
This guide will show you how to setup and use your X2 LED fixture. Please review the entire manual prior to operation.
OVERVIEW
YOUR KIND LED X2 COMES WITH:
- KIND LED X2 Light Fixture
- Power Cord
- RJ-14 Data Cable (x2)
- RJ-14 Dual Cable Splitter
- IP-65 Housing for RJ-14 Connection
GETTING STARTED
Your KIND LED X2 comes fully assembled, ready to grow. Before unpacking your
fixture, place the box flat on the ground, below your intended hanging
location, with the top of the box facing upward.
Top of Box
Remove the top of the box, then remove the protective foam packaging inserts. Lower your adjustable hanging hardware (not included) to the four eyelets found on the top side of the fixture. Once Connected, raise the light o the desired position.
BEST PRACTICES
ENVIRONMENT When using the KIND LED X2, ideal grow room temps should be around
80-85 degrees F. Any lower than this and transpiration can slow, stunting
growth. Any hotter than this and heat stress can form.
NOTE: High PPFD growing conditions require high levels of attention to detail
including proper feeding and CO2 augmentation. For more please visit
kindledgrowlights.com
RECOMMENDED HANGING HEIGHT The KIND LED X2 is designed to excel in close
proximity environments but can be used in a variety of applications.
For best practices, a minimum fixture height of 6″ above the canopy is
recommended. The ideal recommended hang height above canopy is 12″ to maintain
the greatest intensity over the largest footprint. To maintain usable
intensity at a greater distance and larger, a maximum of 18″ above the canopy
is recommended.
For applications that require less intensity such as Cloning Stages and early
Vegetative Stages, a distance from canopy greater than 18″ may be suitable.
SPECIFICATIONS
Spectrum|
3 Channel – Fully Adjustable*
---|---
Efficacy| 2.2 umol/J
PPF| 1650 umol/s
Max Wattage| 750w +/-5%
Input Voltage| 120-277v
Power Factor| 0.975 @ 240v
Diodes|
384 OSRAM OSLON SSL
Lifetime| >75,000 Hours
Dimensions|
39.4” x 39.4” x 4.3”
Cord Length| 6’
RMH (recommended mounting height above canopy)| =+/- 12”
PPFD @ RMH|
859.86 umol/s/m2
Warranty| 5 Year
Certifications| IP65, FCC
Power Factor Diodes
POWER CORDS
Your KIND LED X2 comes with a 6ft., 240v standard power cord. For alternative
power cord recommendations please contact a KIND LED Grow Lights customer
service representative to assist in your selection.
EXTERNAL CONTROLLER CABLES
The KIND LED X2 comes complete with a set of 7 foot RJ14 data cables and a
three way splitter. If your installation requires a longer cable, please
contact a KIND LED Grow Lights customer service representative to guide you in
the purchase of the correct cable for your needs. It is important to select
the correct cable for successful operation of your light fixtures.
YOU ARE READY TO GROW!
For complete control of your KIND LED X2 timing schedules, spectrum and intensity, consider adding the optional Grow Strong GSI-1 Digital Lighting Controller. The GSI-1 controller can operate up to 512 fixtures split between two independent zones. For more information on this fixture and all available options, contact a KIND LED Grow Light customer service representative at KindLEDGrowLights.com or call (855) 559–5463
FCC COMPLIANCE STATEMENT
The KIND LED X2 Commercial Lighting System has been tested at FCC-certified
laboratories in the United States and conforms to FCC’s Part 15B Consumer
Standard for Industrial, Scientific, and Medical Equipment for both conducted
and radiated emissions.
Given that all electronic equipment emits some RF energy, please note that
compliance with
these standards does not mean a zero level of emission, only very low levels.
Per FCC
requirement:
This product may cause interference to radio equipment and should not be
installed near
Maritime safety communications equipment or other critical navigation or
communication
equipment between 0.45-30 MHz.
This device complies with Part 15B of the FCC Rules.
Changes or modifications not expressly approved by KIND LED could void the
user’s authority to operate the equipment.
Please visit www.KindLEDGrowLights.com for a complete documentation of the
KIND LED Commercial Lighting Terms of Use. Thank You.