LANCOM GS-3126X 26-Port Gigabit Ethernet Switch User Guide
- June 8, 2024
- LANCOM
Table of Contents
LANCOM GS-3126X 26-Port Gigabit Ethernet Switch
OVERVIEW
-
Configuration interface (Console) Connect the configuration interface via the included serial configuration cable to the serial interface of the device you want to use for configuring / monitoring the switch.
-
TP Ethernet interfaces Use Ethernet cables to connect the interfaces 1 to 24 to your PC or a LAN switch.
-
SFP+ interfaces Insert suitable LANCOM SFP modules into the SFP+ interfaces 25 to 26. Choose cables which are compatible with the SFP modules and connect them as described in the module’s documentation.
-
Power connector (device back side) Supply power to the device via the power connector. Please use the IEC power cable supplied or a country specific LANCOM Power Cord.
-
ATTENTION: High touch current possible! Connect to earth before connecting the power supply.
➀ System LED
Off| Device powered off
Green| Device operational
Red| Hardware error
➁ Reset button
Pressed until all port LEDs are off|
Pressed until all
port LEDs glow permanently| Configuration reset and device restart
➂ TP Ethernet ports
Off| Port inactive or disabled
Green| Link 1000 Mbps
Green, blinking| Data transfer, link 1000 Mbps
Orange| Link ≤ 100 Mbps
Orange, blinking| Data transfer, link ≤ 100 Mbps
➃ 10 G SFP+ ports
Off| Port inactive or disabled
Blue| Link 10 Gbps
Blue, blinking| Data transfer, link 10 Gbps
Green| Link 1 Gbps
Green, blinking| Data transfer, link 1 Gbps
Hardware
Power supply| Internal power supply unit (100–240 V, 50-60 Hz, 1 A max.)
Power consumption| Max. 30 W
Environment| Temperature range 0–40° C; humidity 10–90 %, non-condensing
Housing| Robust metal housing, 1 HU with removable mounting brackets for 19“
installation, 442 x 44 x 211 mm (W x H x D)
Number of fans| 1
Interfaces
ETH
SFP+| 24 TP Ethernet ports 10 / 100 / 1000 Mbps 2 SFP+ ports 1 / 10 Gbps 26
concurrent ports in total
Package Content
Mounting brackets| Two 19” brackets for rack mounting
Cable| IEC power cord 230 V, serial configuration cable 1.5 m
Before initial startup, please make sure to take notice of the information
regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a
nearby power socket that is freely accessible at all times.
The mains plug of the device must be freely accessible.
Please observe the following when setting up the device
→For devices to be operated on the desktop, please attach the adhesive rubber
footpads
→Do not rest any objects on top of the device or stack multiple devices
→Keep all ventilation slots of the device clear of obstruction
→Mount the device into a 19” unit in a server cabinet using the provided
screws and mounting brackets.
→Please note that support service for third-party accessories is excluded.
This product contains separate open-source software components which are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device‘s WE Bconfig interface under “Extras > License information“. If the respective license demands, the source files for the corresponding software components will be made available on a download server upon request.
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen,
declares that this device is in
compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation
(EC) No. 1907/2006. The full text of the EU Declaration of Conformity is
available at the following Internet address:
www.lancom–systems.com/doc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>