BRESSER BR-S60-RGB LED Panel Instruction Manual

: June 8, 2024
: BRESSER

Table of Contents

BRESSER BR-S60-RGB LED Panel
GENERAL WARNINGS
WARRANTY & SERVICE
SCOPE OF DELIVERY (FIG. 1)
PARTS OVERVIEW
POWER SUPPLY
REMOTE CONTROL
TECHNICAL DATA
Service
Documents / Resources

BRESSER BR-S60-RGB LED Panel

GENERAL WARNINGS

RISK OF PHYSICAL INJURY!
Do not use in the presence of children or animals. Store out of reach of children and animals.
DANGER OF MATERIAL DAMAGE!
Make sure that no one can trip over connection cables of the device. The device could be knocked over. Only use the recommended power cable or the recommended battery for the power supply! The manufacturer assumes no liability for voltage damage caused by the use of an unsuitable voltage supply!
DANGER OF AN ELECTRIC SHOCK!
This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the instructions. Otherwise there is a RISK of ELECTRIC SHOCK. Never bend, squeeze or pull power cables, connecting cables, extensions or connectors. Protect cables from sharp edges and heat. Check this device, cables and connections for damage before use. Never attempt to operate a damaged device, or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent. Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.
RISK OF GLARE!
Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.

FIRE/EXPLOSION HAZARD!
Always place the device in such a way that it cannot tip over and ensure that it is stored in a reasonably safe place.

Keep children and animals away from the device! They could knock the device over.
Make sure that no one can trip over connection cables. The device could be knocked over.
Do not expose the device to high temperatures. Do not shortcircuit the device or dispose of in fire! Excessive heat and improper handling can cause short circuits, fires and even explosions!
Only use the recommended power adapter*!

IMPORTANT NOTE!
Never take the device apart. In the event of a defect, please contact your dealer. They will contact the Service Centre and can arrange the return of this device for repair if necessary. Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation and before any maintenance and cleaning work. Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the mains supply. To disconnect the unit from the mains, always pull the mains plug and never pull the cable! Do not subject the device to excessive vibrations.

INFORMATION ABOUT THE PRODUCT
Thank you for purchasing this product. High-quality light-emitting diodes (LED) with high performance were installed in this studio light. The LED generate less heat and prevent damage from overheating. This increases their lifespan and they require less energy. The lamp housing is made of high- quality aircraft aluminum and is therefore very robust.
EC DECLARATION OF CONFORMITY
A “Declaration of conformity” in accordance with the applicable directives and corresponding standards has been prepared by Bresser GmbH. The full text of the EU declaration of conformity is available at the following internet address:
www.bresser.de/download/F004359/CE/F004359_CE.pdf
UKCA DECLARATION OF CONFORMITY
A “Declaration of conformity” in accordance with the applicable directives and corresponding standards has been prepared by Bresser GmbH. The full text of the EU declaration of conformity is available at the following internet address:
www.bresser.de/download/F004359/CE/F004359_CE.pdf
Bresser UK Ltd.
Suite 3G, Eden House · Enterprise Way
Edenbridge, Kent TN8 6HF
Great Britain

WARRANTY & SERVICE

The regular guarantee period is 2 years and begins on the day of purchase. To benefit from an extended voluntary guarantee period as stated on the gift box, registration on our website is required. You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms.

www.bresser.de/warranty_terms

SCOPE OF DELIVERY (FIG. 1)

LED light (A), mains adapter with cable (B), remote control (C)

PARTS OVERVIEW

LED LIGHT (A)

LED panel
Barn doors
Locking screw (rocker joint)
Vent
Battery holder
MODE button
Channel button
DMX connection socket (RJ45 type)
U bracket
Fixing screw (tripod connection)
Tripod connection
LED display
DC connection socket
On/Off button
Adjustment knob and ‘DIMMER/COLOR’ button
MAINS ADAPTER WITH CABLES (B)
Mains adapter with 2-pin connection socket (14a)
Voltage cable (permanently connected to mains adapter) with DC hollow plug (15a)
Power cable with 2-pin C7 plug (16a) and Euro plug (16b)
function light
REMOTE CONTROL (C)
LCD display
Power button
– button
Menu button
+ button
Battery compartment

DISPLAY

Screen display
Value power for color temperature in K (Kelvin)
Function light ‘COLOR’
Function light ‘CCT/RGB’
Function light ‘DIMMER’

POWER SUPPLY

USING MAINS ADAPTER (STANDARD)

Plug the 2-pole C7 plug (18a) of the power cable (18) into the C8 connection socket (14a) on the power adapter (14).
Plug the DC hollow plug (17a) of the voltage cable (17) on the mains adapter (B/16) into the DC connection socket (13) on the LED light (B).
Plug the Euro plug (18b) of the power cable (18) into the mains socket.

*USING V-MOUNT BATTERIES (optional)**

Slide the fully charged batteries* (2 pieces of type NP-F750 or NP-F960) into the battery holder (5) from above so that the battery clicks into place.
To remove, slide the battery out of the holder in the opposite direction.

TURNING THE LED LIGHT ON

Establish the power supply for the device (insert battery or connect to mains voltage).
Press the On/Off button (14) to switch on the device.
Press the On/Off button (14) again to switch off the device.

BRIGHTNESS ADJUSTMENT

Press the “DIMMER/COLOR” button (15).
When the corresponding function light “DIMMER” (28) lights up brightly, you can adjust the brightness by turning the adjustment knob (15).

COLOR TEMPERATURE ADJUSTMENT

Press the “DIMMER/COLOR” button (15).
If the corresponding function light “COLOR” (28) lights up brightly, you can set the color temperature (32 to 56 / corresponds to 3200K to 5600 K) by turning the adjustment knob (15).

ADJUSTING THE RGB COLORS

Press the “MODE” button (6).
When the corresponding function light “CCT/RGB” (29) lights up brightly, you can set the desired RGB color (0 to 360) by turning the adjustment knob (15).

SETTING A CHANNEL

Press the Channel button (7).
The last set channel (0-99) flashes.
Set the desired channel (0 to 99) by turning the adjustment knob (15).
Finally, press the Channel button (7) to save the set channel.

REMOTE CONTROL

**USING A DMX CONTROLLER***

Connect your DMX controller to the light using a suitable RJ45 connection cable via the DMX sockets (8).
Turn on the light and the DMX controller*.
Press the DMX/2.4G button. The DMX function is activated when the corresponding indicator lights up. When the DMX function is activated, the light can only be controlled via the DMX controller*.

USING THE 2.4G REMOTE CONTROL

Press the On/Off button (21) to switch on the device.
Long press the power button (21) to turn off the device.

SCROLL THROUGH THE MENU
Press the menu button (23) to scroll through the menu.

Press 1x = Display 10 “Brightness” 10 = 10%
press 2x = display 56 “color temperature” 56 = 5600K
Press 3x = display 01 “channel” 01 = 1

Choosing a channel

Press the menu button (23) three times to get to the channel menu.
Press + or – (22/24) to select the desired channel.
Press the menu button (23) to confirm your selection.

SWITCH LIGHT ON/OFF

By default, the light status of the selected channel is “OFF”.
Press the On/Off button (21) to turn on the light.
Long press the On/Off button (21) to turn off the light.

ADJUSTING THE BRIGHTNESS

By default, the brightness level is 10% when the device is turned on.
Press the + or – button (22/24) to increase or decrease the brightness.

SETTING THE COLOR TEMPERATURE

Press the menu button (23) to select the color temperature for the current channel.
Press + or – button (22/24) to choose the desired color temperature.

ADJUSTING THE TILT ANGLE

Hold the light and slowly loosen the locking screw (3) for the rocker joint.
Bring the light head into the desired position and hand tighten the locking screw (3) again.

*MOUNTING ON A TRIPOD (optional)**

Loosen the fastening screw (10) for the tripod connection (11) so far that the opening of the tripod connection is exposed.
Place the light with the opening of the tripod connection on the spigot adapter of a tripod and tighten the fastening screw.

DISPOSAL
Dispose of the packaging materials by type. Observe the current legal regulations when disposing of the device! Information on proper disposal can be obtained from municipal waste disposal service providers or the Environmental Agency. Do not dispose of electronic devices in the household waste! According to the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its transposition into national law, used electrical equipment must be collected separately and recycled in an environmentally sound manner.

TECHNICAL DATA

Model	BR-S60 RGB
Power Output	60W
Luminous flux	600LM
Number of LEDs	white: 600 pcs. colored (RGB): 81 pcs.
Colour temperature	3200K-5600K

stepless adjustment

Light source| 0.5W SMD LED/1.5W RGB LED
Color rendering index (CRI)| ³95
Dimmer| 10-100%

DMX control

| ****

via RJ45

Remote control

| 99 channels,

2.4G wireless remote control

Service

Please contact the service centre first for any questions regarding the product or claims, preferably by e-mail.
e-mail: service@bresseruk.com
Telephone: +44 1342 837 098
BRESSER UK Ltd
Customer Support
Suite G3, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
United Kingdom
Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de
@BresserEurope

Bresser UK Ltd.
Suite 3G, Eden House · Enterprise Way
Edenbridge, Kent TN8 6HF · Great Britain

Errors and technical changes reserved. · Fouten en technische wijzigingen voorbehouden. Irrtümer und technische Änderungen vorbehalten. Manual_F004359_BR-S60-RGB_en-nl-de_BRESSER_v102022a

Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

WARRANTY

www.bresser.de/warranty_terms

RECYCLAGE (TRIMAN/FRANCE)

BRESSER-BR-S60-RGB-LED-Panel-FIG6