ATC-1000WF Converter User Guide

: June 8, 2024
: ATC

Table of Contents

Check Package Content
Hardware Installation
LED indication&Factory default button
Software Installation
Configure the ATC-1000WF
Factory Default WLAN &IP Address
- IP Parameters
- WLAN Parameters
Quick connection in AP mode
Quick Connection by AT+Command:
General Specification
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

ATC-1000WF Converter User Guide

Check Package Content

ATC-1000WF unit 1Pcs
Mono pole Antenna (2dBi RP-SMA) 1Pcs
Software CD 1Pcs
External power adapter 1Pcs
RS-232 cross cable 1Pcs
Quick Start Guide_Ver 2.1 1Pcs

Hardware Installation

Connect RS-232 DB9 Female Crossing configuration cable
to ATC-1000WF unit on RS-232 side.
Connecting the Power Adapter to ATC-1000WF power jack. When the power is properly supplied. The Ready LED will on Green light and PWR LED will light in red.

RS-232/422/485 Pinout
RS-232 Pinout(DB9 Male )

PIN	RS-232	Input/Output
2	RXD	I
3	TXD	O
5	GND	–

RS-422/485 Pinout(6Bit-Block Terminal from left)

PIN	RS-422	RS-485
1	T+	485+
2	T-	485-
3	R+	–
4	R-	–
5	VIN+	VIN+
6	VIN-	VIN+

LED indication&Factory default button

LINK —- Indicate WLAN status.Light means ATC-1000WF (STA mode) collected to AP or laptop &mobile connect to ATC-1000WF(AP mode)
Ready —- It show light when ATC-1000WF boot up ready.
Tx/Rx —- It show data send or receive from serial port.
PWR —- Indicate the Power supply
Factory Default – To restore ATC-1000WF to factory default.

Factory Default Button

Step1: Power on ATC-1200 and find the button above photo.
Step2: Press button near the terminal block wait about 5 seconds
Step3: Release the button and ATC-1000WF will be automatic to restart from factory default setting.

Software Installation

Insert the software CD and search for suchasF:/Tool/Tera-Term to install.
Note: Be sure youhaveadministrative rights &disable firewalls in windowsXP

Configure the ATC-1000WF

ATC-1000WF supports two methods to configurationparameters:Web Accessing and AT+instructionset. Web accessing means users can configure parametersthrough Web browser. When ATC 1000WFconnectedtowireless network. Parameters configuration is doneonaPCconnected to the same wireless network. AT+instruction set configuration means user configureparameters through serial interface(RS-232/422/485) command.Refer to ATC-1000WF User’s Manual. “AT+instruction set”chapter for more detail. Before configuring the ATC-1000WF on AT+instructionmode,you should turn off the power and use a serial cableconnectthe ATC-1000WF to your computer’s serial port(RS-232).
We suggest using Tera-Termto operate.Firstlyyoushouldconfigure Tera-Term serial port like below:57600bpsforbaudrate ,8bits for data-length,NONE for parity bit ,1bit for stopbits.
Upon power up.The ATC-1000WF will be inAPmodefromfactory producing. To enter command mode, youshouldsend““+++”. The device will respond with “a ”.Theninput“a”While it change to command mode.It also show”+OK” andtheATC-1000WF will accept ASCII bytes as command. Youcanusing”AT+H” for all the command you need . Toexit commandMode and reset.Please send “AT+Z”.The devicewill respondwith “OK” restart and return AP mode. The parameters such as the SSID, channel, IPaddress, serialport settings, And all other settings can be viewedandconfigured in command mode.

Factory Default WLAN &IP Address

UART Parameters

Mode: RS-232
Data-length: 8
Stop-bits: 1
Baud-rate: 57600
Parity: n (none)
Flow : n (none)

IP Parameters

Protocol: TCP Server
Local port:: 8899
DHCP Client: Enabled
Static IP Address: 10.10.100.254
Net Mask: 255.255.255.0
Gateway: 192.168.2.1
DHCP Server: Enabled
IP Address: 0.0.0.0
Net Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DNS: 0.0.0.0

WLAN Parameters

Channel: 11
SSID: HF-A21x_AP
Mode: AP
Data-rate: Auto

Quick connection in AP mode

ATC-1000WF AP Mode is the default setting.

Step1: Power on ATC-1000WF.
Step2: Use a device(Laptop or mobile) with a wireless network card.We suggest using Mobile as well.
Step3: Pleas use iPhone or Android mobile.To use setting button search for WiFi network AP with SSID name is:HF-A21x_AP

SETTING

Step5: On cellphone browser address input 10.10.100.254 then click you can get below page show ask you to input User name and Password
Log in IP Address: 10.10.100.254
User Name: admin
Password: admin

LOGIN

Step6: You can get main page.The main menu include five pages: “Mode Selection”,” AP Interface Setting”,”STA Interface Setting”,”Application Setting”, and “Device Management”

CONFIGURATION MODE

On Mode Selection menu.User needtochooseSTAmode and then click below button “Apply” toconfirmthe modification. Step7: This step is most important allowATC-1000WFto access available Wi-Fi AP.Click STAInterfaceSetting.You can see web page on right sidetherehave STA Interface Parameters list. On first list we can see AP’S SSID.Onright columnthere have Search Button.We click it andappearbelow SSID AP router list.We chooseH3CAPtoshow how to setting below step.

INTERFACE SETTING

SITE SURVEY

After you apply to access H3C AP router then need you input wireless access password and click apply button.

INTERFACE SETTING

Now we have finished Wi-Fi setting and we will try to last step to setting WAN connection setting.We usually choose STATIC(Fixed IP) for ATC-1000WF. We need fill these parameters into below options. (You also need be to know the router assigned IP address range and Gateway IP address whatever your want to join it in).Our Wi-Fi router parameter as following:
IP address range: 192.168.1.2-255
Subnet Mask: 255.255.255.0
Gateway Address: 192.168.1.1

STATIC MODE

Input below value and click apply button again. Address:192.168.1.125 Subnet Mask:255.255.255.0 Default Gateway:192.168.1.1 After finished above setting we need to make the ATC-1000WF restart and make it effected.On the Device Management manual you need to Click Restart button to make all of setting take effect.

DEVICE MANAGEMENT

Quick Connection by AT+Command:

User can input AT+ Instruction throughhyper terminalor other serial debug terminal.Also canprogramtheAT+ Instruction to script. User can alsoinput “AT+H”to list all AT+ Instruction and descriptiontostart.SeeNo.5 for detail enter AT+Command mode. For example there have one Wi-Fi networkasfollowing parameter:

SSID: H3C
Encryption method: WPAPSKPassword:12345678
Preset ATC-1000WF Static IP address: 192.168.1.125Subnet Mask: 255.255.255.0
Router gateway IP address: 192.168.1.1

Step 1: Setting ATC-1000WF working on StationMode.AT+WMODE=STA (STA/AP) +ok Also can use AT+WMODE to seewhetheriteffective.
Step 2: Setting ATC-1000WF wireless encryptionmethodtoaccording wireless router requirement. AT+ WSKEY=< auth,encry,key>◼

Parameters:
auth: Authentication mode OPEN SHARED WPAPSK
Encry: Encryption algorithmNONE: When “auth=OPEN”, effective
key: password, ASCII code, shall less than 64 bit an greater than 8bit. This Instruction only effective for ATC-1000WF works as STA. After ATC-1000WF module boots up again, the setting will be effective

AT+WSKEY=WPAPSK,AES,12345678 +ok

Type below command to see ATC-1000WF wireless parameter of encryption.

AT+WSKEY +ok=WPAPSK,AES,12345678

Step 3, Set the SSID parameters of the wireless network. AT+WSSSID ◼ Function: Set/Query WIFI target AP SSID parameters as STA. ◼ Format:

Query Operation AT+WSSSID +ok=<ap’s ssid>< LF >< LF >
Set Operation AT+ WSSSID=<ap’s ssid > +ok< LF >< LF > ◼ Parameters:
ap’s ssid: AP’s SSID AT+WSSSID=H3C +ok AT+WSSSID +ok=H3C

Step 4 ,Query the current module IP address AT+ WANN ◼ Function: Set/Query WAN setting, only effective as STA mode; ◼ Format:

Query Operation AT+WANN +ok=<mode,address,mask,gateway>< LF >< LF >
Set Operation AT+ WANN=< mode,address,mask,gateway > +ok< LF >< LF > ◼
Parameters:
mode: IP setting for WAN port static: Static IP DHCP: Dynamic IP
ddress: WAN port IP address;
mask: WAN port subnet mask;
gateway: WAN port gateway address;

AT+WANN=STATIC,192.168.1.125,255.255.255.0,19 2.168.1.1 +ok So after setting as above step1-step4.The ATC-1000WF will automatic to access existing Wi-Fi wireless network(SSID:H3C).More other detail AT+ Command see ATC-1000WF User’s Manual (Ver2.1 )as well.Please see below total AT+Command setting list again.

AT+WMODE=STA
AT+WSKEY=WPAPSK,AES,12345678
AT+WSSSID=H3C
AT+WANN=STATIC,192.168.1.125,255.255.255.0,19 2.168.1.1

General Specification

*Class*	*Item*	*Parameters*
********Wireless Parameters	Certification	FCC/CE
Wireless standard	802.11 b/g/n
Frequency range	2.412GHz-2.484GHz
****Transmit Power	802.11b: +20 dBm (Max.)