PROMINENCE HOME 40278 Glenmont Ceiling Fan Owner’s Manual
- June 8, 2024
- PROMINENCE HOME
Table of Contents
PROMINENCE HOME 40278 Glenmont Ceiling Fan
Ifa problem cannot be remedied or you are experiencing difficulty in
installation, please contact the service department.
1-877-459-3267 8 a.m.-5 p.m Central,
Monday-Friday
Keeping You Cool ls What We Do Best!
PACKAGE CONTENTS
Unpack your fan and check the contents. You should have the following items
:
-
Canopy
-
Canopy Cover
-
Mounting Bracket
-
Mounting Bracket Screw (x4)
-
Downrod
-
Downrod Pin
-
Downrod Clip
-
Yoke Cover
-
Set Screw (x2)
-
Closemount Screw (x3)
-
Motor Assembly
-
Motor Screw (x10)
-
Fitter Plate
-
Fitter Plate Screw (x3)
-
Switch Housing Cap
-
Light Kit
-
Socket Ring (x3)
-
Glass Shade (x3)
-
Owner’s Manual
-
Hardware Kit
-
Blade Arm (x5)
-
Blade (x5)
-
E26-base LED Bulb (x3)
HARDWARE CONTENTS -
Blade Screw (x15)
-
Blade Washer (x15)
-
Wire Connector (x3)
-
Pull Chain Extension (x2)
Note: Some extra hardware has been included. The quantity listed above is the number required for installation.
HARDWARE CONTENTS
DIMENSION REFERENCE
A. 13.58 in. B. 9.21 in. C. 6.74 in. D. 5.13 in.
MOUNTING OPTIONS
Three Mounting Options
Choose one of the following mounting options:
- Closemount method is best suited for ceilings lower than 8 feet. It does not utilize the downrod.
- Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included).
- Angled Ceiling Mount is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to ensure proper blade clearance from the ceiling.
- If using the angle mount, check to ensure the ceiling angle is not steeper than 16°.
SAFETY INSTRUCTIONS
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN
INSTALLING THE FAN AND SAVE INSTRUCTIONS.
CAUTION:
- All set screws of the fan must be checked and retightened where necessary before installation.
- To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
- Before changing the fan direction, turn off the fan and wait for the fan blades to stop completely.
- The safeguards provided by these safety instructions and by the separate installation instructions are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be supplied by the person(s) installing, caring for and operating the fan.
- The fan weight is Net Weight: 21.5 lb (9,75kg). Be sure the outlet box (not included) is securely attached to the building structure and is marked “Acceptable
- For Fan Support”. Failure to do so can result in serious injury.
- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Please note changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING:
- To avoid risk of electric shock, be sure to shut off power at the main fuse or circuit breaker box before installing or servicing this fixture. Turning off the electrical power by using the light switch is not sufficient to prevent electrical shock.
- To reduce the risk of injury, install the fan so that the blades are at least 7 feet (2.1 Meters) above the floor and at least 18 inches (0.5 Meters) from the tip of the blades to the wall.
- To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting screws provided with the outlet box.
- The installation has to be in accordance with the national electrical code, ansi/nfpa 70-1999 and local codes. If you are unfamiliar with the methods of installing electrical wiring, seek the services of a qualified licensed electrician.
- Using a full-range dimmer switch to control fan speed will cause a loud humming noise from the fan. To reduce the risk of fire or electric shock, do NOT use a full-range dimmer switch to control the fan speed.
ASSEMBLY INSTRUCTIONS
-
Turn OFF the electrical power at the main fuse or circuit breaker.
-
Remove the mounting bracket by removing the two mounting bracket screws from the round holes in the canopy. Then loosen the other two mounting bracket screws from the J-shaped slots. Retain the mounting bracket screws for later. Install the mounting bracket to the outlet box (not included) using the screws and washers provided with the outlet box.
Warning: To reduce the risk of fire, electric shock, or personal injury, mount to the outlet box marked “acceptable for fan support” and use the mounting screws and washers provided with the outlet box. -
Remove all 10 preassembled motor screws and plastic motor blocks from the underside of the motor assembly. Discard the motor blocks, but save the motor screws for later use.
-
CLOSEMOUNT INSTALLATION (OPTIONAL)
- a. Remove the canopy cover from the bottom of the canopy.
- b. Remove the three Phillips-head closemount screws from the top of the motor assembly.
- c. Align the holes in the bottom of the canopy with the screw holes in the top of the motor assembly. The larger holes in the canopy will encompass the three pre-installed screws.
- d. Secure the canopy to the top of the motor assembly with the closemount screws that were previously removed.
- e. Hang the fan on the hook of the mounting bracket. Proceed to Step 9.
DOWNROD INSTALLATION:
-
Remove the downrod clip and downrod pin from the downrod. Then partially loosen the two set screws in the yoke at the top of the motor assembly.
-
Feed the wires coming from the yoke through the yoke cover, canopy, and downrod.
-
Insert the downrod into the yoke and re-install the downrod pin and downrod clip. Then re-tighten the two set screws.
Note: With wiring extending out of the downrod, measure 8 inches of lead wire and cut the excess wire with wire cutters (not included). Then strip 1/2” of insulation from the end of each wire. -
Lift the downrod into the mounting bracket. Rotate the downrod until the tab in the mounting bracket is seated in the slot in the downrod ball.
WARNING: The fan and/or downrod should not rotate in the mounting bracket if installed correctly. Failure to align the slot in the downrod ball with the tab on the mounting bracket may result in fan falling causing serious injury or death. -
Use wire connectors to connect the fan wires to the power supply wires according to the wiring diagram and the following instructions:
- Connect the green wire from the downrod and mounting bracket to the bare/green (ground) supply wire.
- Connect the white wire from the fan to the white (neutral/common) supply wire.
- Connect the black and blue wires from the fan to the black (live/hot) supply wire.
Note: Closemount installation does not use the downrod, so there will only be two green wires to connect.
Note: If there is a second hot/power wire coming from the outlet box, connect it to the Blue (light power) fan wire for separate light and fan control.
Important : After the connections have been made, the connected wires should be turned upward and pushed carefully up into the outlet box. Place the black and white wire connections on opposite sides of the outlet box.
-
Raise the canopy, ensure the two mounting bracket screws are aligned with the J-shaped slots in the canopy. Then turn the canopy in a clockwise direction until the mounting bracket screws are completely engaged in the J-shaped slots. Install the two previously removed mounting bracket screws in the round holes. Securely tighten all four mounting bracket screws.
-
Partially insert the blade screws along with the blade washers through the blade and into the blade arm. Tighten each blade screw with a Phillips screwdriver (not included), starting with the one in the middle. Repeat this step for the remaining blades and blade arms.
-
Install the blade arm to the underside of the motor assembly with the motor screws previously removed in Step 3. Tighten with Phillips screwdriver. Repeat for each blade arm. Note: The notch in the fitter plate provides a Phillips screwdriver access to the motor screw holes.
-
Note: If you wish to install the fan without the light kit, proceed to Step16.
To install the light kit, remove the three fitter plate screws from the fitter plate. Then connect the single-pin connector from the fitter plate to the single-pin connector in the light kit–blue to black and white to white. Secure the light kit to the fitter plate using the previously removed fitter plate screws. -
Remove the three socket rings from each of the sockets on the light kit. Lift glass shades onto the light kit and secure with previously removed socket rings.
-
Install the E26-base B10 LED bulbs into the sockets of the light kit.
-
To install without the light kit, remove the three fitter plate screws from the fitter plate. Then attach the switch housing cap to the fitter plate using the fitter plate screws.
-
Attach the pull chain extensions to each of the pull chains. The fan pull chain extends from the side of the light kit and the light pull chain extends from the center of the light kit.
-
Restore the power at the main fuse or circuit breaker.
OPERATING INSTRUCTIONS
- The fan pull chain has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. The light pull chain has two positions to control the light, ON and OFF.
- Use the reverse switch, located on the fitter plate to optimize your fan for seasonal performance.
Using a ceiling fan will allow you to raise your thermostat setting in summer and lower your thermostat setting in winter without feeling a difference in your comfort.
In warmer weather, push the reverse switch to the left which will result in downward airflow creating a wind chill effect.
In cooler weather, push the reverse switch to the right which will result in upward airflow that can help move stagnant, hot air off the ceiling.
Important: Wait for the fan to stop before moving the reverse switch. The reverse switch must be set either completely left or right in order for the fan to function correctly. If the reverse switch is set in the middle position, the fan will not operate.
TROUBLESHOOTING
If you have difficulty operating your new ceiling fan, it may be the result of
incorrect assembly, installation or wiring. In some cases, these installation
errors may be mistaken for defects. If you experience any faults, please check
the Troubleshooting section below. If a problem cannot be remedied or you are
experiencing difficulty in installation, please contact the Service
Department: 1-877-706-3267, 9 a.m.- 5
p.m. Central time.
LIMITED LIFETIME WARRANTY
To obtain Service, please contact the Service Department:
1-877-706-3267, 9 a.m.- 5 p.m. Central
time.
Model Name: 52” Glenmont Ceiling Fan
Model No: 50388 – Antique Pewter
50389 – Distressed White
The manufacturer warrants this fan to be free from defects in workmanship and
materials present at time of shipment from the factory for a lifetime from the
date of purchase by the original purchaser. The retailer also warrants that
all other fan parts, excluding any glass or acrylic blades, to be free from
defects in workmanship and material at the time of shipment from the factory
for a period of one year after the date of purchase by the original purchaser.
The manufacturer agrees to correct such defects without charge or at its
option replace the ceiling fan with a comparable or superior model. To obtain
warranty service, present a copy of the receipt as proof of purchase. All
costs of removing and reinstalling the product are your responsibility. Any
damage to any part such as by accident or misuse or improper installation or
by affixing any accessories, is not covered by this warranty. The manufacturer
assumes no responsibility whatsoever for fan installation during the limited
lifetime warranty. Any service performed by an unauthorized person will render
the warranty invalid. Due to varying climate conditions, this warranty does
not cover any changes in brass finish, including rusting, pitting, corroding,
tarnishing or peeling. Brass finishes of this type give their longest useful
life when protected from varying weather conditions. Any glass provided with
this fan is not covered by the warranty. Any replacement of defective parts
from the ceiling fan must be reported within the first year from the date of
purchase. For the balance of the warranty, call our customer service
department for return authorization and shipping instructions so that we may
repair or replace the ceiling fan. Any fan or parts returned improperly is the
sole responsibility of the purchaser. There is no other expressed warranty.
The manufacturer disclaims any and all warranties. The duration of any implied
warranty which cannot be disclaimed is limited to the time period as specified
in the expressed warranty. The manufacturer shall not be liable for
incidental, consequential, or special damages arising out of or in connection
with product use or performance except as may otherwise be accorded by law.
This warranty gives specific legal rights, and you may also have other rights
which vary from state to state. This warranty supersedes all prior warranties.
Note: A small amount of “wobble” is normal and should not be considered a
defect.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>