home LTC 04 Digital 3D LED Alarm Clock Instruction Manual

: June 8, 2024
: home

Table of Contents

INSTALLATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

home LTC 04 Digital 3D LED Alarm Clock Instruction Manual

LED	4-digit, white
LED heigh	3,14” / 80 mm
LED size	232 x 80 mm
Dimensions	235 x 100 x 50/25 mm
Weight	180 g

PRI	230 V~ 50 Hz / 0,3 Amax
SEC	5 V / 1,2 Amax.
Wire	~180 cm
Backup batt	3 V (CR2032)
Ta	5 – 35 °C

Before using the product for the first time, please read the instructions or use
below and retain them for later reference. The original instructions were written in Hungarian language. This appliance may only be used by persons with impaired physical, sensory or mental capabilities, or lacking in experience or knowledge, as well as children from the age of 8, if they are under supervision or have been given instruction concerning use of the appliance and they have understood the hazards associated with use. Children should not be allowed to play with the unit. Children may only clean or perform user maintenance on the appliance under supervision.

After unpacking the product, make sure it has not been damaged during transport. Keep children away from the packaging material, if it contains polybag or other hazardous components.

3,14” / 80 mm high, white 3D LED display
it’s clearly visible at night
and daytime
readable even from 30 meters distance
3 stages of
brightness selectable (20-70-100%)
energy saving, night mode
brightness is adjustable for durations
12 – 24 hour time forma
•alarm with 2 minutes beep-beep sound
5-60 minutes programmable wake up
alarm repeating
placement on desktop or wall mountable
for the case
of power cut, time memory can be ensured with CR2032 (3 V) button
cell, included
power supply: USB adapter and ~1,8 m USB cable
(included)
dimensions: 235 x 100 x 25 mm / 180 g

INSTALLATION

Power supply can be provided in more ways. For time memory of the clock a CR2032 (3V) button cell is needed. This is delivered together with the product. If the clock later forgets the accurate time – e.g. it was powered off due to a relocation – the button cell has to be replaced. Screw out the lid of the battery holder compartment at the back with the help of a coin. According to the specified polarity, insert a new CR2032 (3V) button cell. For activating the clock LED display connect the delivered USB cable to the included adapter or to a suitable (5 VDC / min. 200 mA) USB power source.

In case of power cut, the display will not light up, but the clock continues operation from the inserted button cell. When the voltage turns back, the clock will show the correct time. In case of power cut, it will not wake up, when operated by the button cell. It is recommended to check the status of the battery sometimes. If the battery is depleted, remove it immediately, since liquid can flow out from it, which may damage the appliance.

WARNING! RISK OF EXPLOSION IN CASE OF INCORRECT BATTERYREPLACEMENT! IT CAN BE DONE ONLY BY SAME OR REPLACINGTYPE! DO NOT EXPOSE BATTERIES TO DIRECT THERMALRADIATION AND SUNSHINE! DO NOT BURN THE BATTERIES. IF THERE IS SOME LIQUID FLOWN OUT FROM THE BATTERY, TAKE A PROTECTIVE GLOVE, AND CLEAN THE BATTERY HOLDER WITH A DRYCLOTH! KEEP BATTERIES OUT OF REACH OF CHILDREN! IT IS FORBIDDEN TO OPEN, BURN AND SHORT-CIRCUIT AND CHARGE BATTERIES RISK OF EXPLOSION!
THIS PRODUCT INCLUDES BUTTON CELL. DO NOT SWALLOW THE BATTERY, RISK OF CHEMICALBURN! IN CASE OF INGESTION, ITCAN CAUSE STRONG INTERNAL BURN WITHIN 2 HOURS AND MAY LEAD TO DEATH! KEEP THE NEW AND USED BATTERIES OUT OF REACH OF CHILDREN! IF THE COVER OF BATTERY COMPARTMENT CANNOT CLOSE PROPERLY, DO NOT USE THE PRODUCT MORE, AND KEEPOUTOF CHILDREN! IF YOU THINK ABATTERY HAS BEEN SWALLOWED OR GOT INTO ONE OF THE BODY PARTS, IMMEDIATELYCONSULTADOCTOR!
Non-rechargeable batteries must not be charged! Risk of explosion! D not insert accumulators instead of batteries because they have a significantly lower voltage and efficiency

TIME SETTING
After installation the display will start lighting. Set the accurate time. Hold the MODE button pressed for 2 seconds, and display will start flashing. Within\ 10 seconds, select with UP/ DOWN buttons, if you want to use 12-hour or 24- hour display format. In case of 12-hour time format, there will be the PM LED is lighting on the front in the afternoon. (e.g.:14:00=PM2:00) After that, press
again the MODE button and the hour-, then the minute- display will be flashing after repeated push of button. The selected data can be set with repeated brief pressing of UP / DOWN buttons. When the time has set, press again the MODE button, to exit setting mode, or wait for 10 seconds to leave.

ALARM
In time-displaying mode press MODE button briefly to display the alarm time for 5 seconds. Flashing of AL LED will show, that the display is indicating not the current time.

If you press and hold the MODE button (2 sec.) within 5 seconds, you can set the hour of the alarm time and after a second press of MODE button you can set the minutes with the UP/ DOWN buttons.

It is similar to the current time setting. After setting the alarm hour and minute, a third parameter can be entered by stepping forward with MODE button and pressing UP / DOWN buttons again. At this time, the counter appearing on the place of minute display can be set between 5 and 60 minutes. This is the interval of SNOOZE function (alarm repeating). Clock will wake you up again after this time elapsed. The factory default setting is 5 minutes. If you don’t exit by pressing MODE button, then the set data will be recorded after 10 seconds. The set alarm time will be active, when the AL LED is lighting. You can switch it on or off with DOWN button.

EPEATING ALARM (SNOOZE)
Alarm signal is 2 minutes long beep-beep sound. To mute it, press the MODE button, the AL LED i s flashing on, then the alarm will sound again after the set interval. The AL LED will be flashing till the alarm process is active, including the terms of snooze as well. If you press DOWN button during the alarm, then there won’t be repeating, and the AL LED won’t be flashing further on. It will exit SNOOZE mode. In SNOOZE mode, you can exit from it with any button.

CHANGING TIME FORMAT
Hold the UP button pressed for 2 seconds, to switch over the 12/24-hour format.

MANUALBRIGHTNESS CONTROL
Press briefly and repeatedly the UP button to select from the 3 available stages of brightness.

AUTOMATIC BRIGHTNESS CONTROL
To switch it on, press briefly twice the MODE button. After first press the alarm time will appear (AL), after second press the OFF or ON text. To change it, use the UP / DOWN buttons. In ON position the brightness of the display will change automatically in the daytime. Depending on which setting of the brightness is actual from small-medium- high versions, the operation of this function changes as follows

high brightness: high brightness from 6:00 to17:59, small brightness from
18:00 to 5:59
medium brightness: medium brightness from 6:00 to 17:59, small brightness from 18:00 to 5:59
small brightness: there’s no changing, brightness stays small all day

AUTOMATIC LIGHT CONTROLPERIOD
If you would like to operate the automatic brightness control different from the factory default setting, you can modify the standard setting of 6:00-7:59 hour and the remaining time. Press briefly the MODE button twice, to get the ON (automatic brightness control is on) indication readable on the display. At this time, hold on the MODE button and „18” hour will flash, then after repeated press the „00” minute. After further pressing of MODE button it will change to „6” and „00” time display. Actually flashing data can be revised and set with UP / DOWN buttons. So the brightness of the display will change at the desired time according to your needs. During setting, the upper or lower part of the centre colon indicates which range is being adjusted

switch over to smaller brightness

switch over to higher brightness

The product is not a toy. Keep out of reach of children. • THIS PRODUCT INCLUDES A BUTTON BATTERY. IT IS FORBIDDEN TO SWALLOW THE BATTERY, RISK OF CHEMICAL BURN. IN CASE OF INGESTION, IT MAY CAUSE STRONG INTERNAL BURN WITHIN 2 HOURS AND MAYLEAD TO DEATH. KEEPTHE NEW AND USED BATTERIES OUT OF REACH OF CHILDREN. IF THE COVER OF THE BATTERY COMPARTMENT CANNOT GET CLOSED SECURELY, DO NOT CONTINUE TO USE THE PRODUCT AND KEEP IT AWAY FROM CHILDREN. IF YOU THINK THAT A BATTERY HAS BEEN SWALLOWED OR GOT INTO ANY BODY PARTS, SEEK MEDICAL ATTENTION IMMEDIATELY

Caution: Risk of electric shock! Do not attempt to disassamble or modify the unit or its accessories. In case any part is damaged, immediately power off the unit and seek the assistance of a specialist.

External power supply specifications external power supply

Manufacturer’s name or trade mark, commercial registration number and address|
08-09-002824
---|---
Model identifie| HX075B-0501200-AG-001

Waste equipment must not be collected separately or disposed of with household waste because it may contain components hazardous to the environment or health. Used or waste equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of product at a facility specializing in the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local waste management organization. We shall undertake the tasks pertinent to the manufacturer as prescribed in the relevant regulations and shall bear any associated costs arising

DISPOSING OF ALKALINE AND RECHARGEABLE BATTERIES • Batteries, whether alkaline or rechargeable, must not be handled together with regular household waste. It is the legal obligation of the product’s user to dispose of batteries at a nearby collection center or at a retail shop. This ensures that the batteries are ultimately neutralized in an environment friendly way.