PPE 845RE Heavy-Duty Cast Aluminum Transmission Pan Installation Guide
- June 8, 2024
- PPE
Table of Contents
PPE 845RE Heavy-Duty Cast Aluminum Transmission Pan
CONTENTS
- A (1) PPE Deep Transmission Pan (GM 10L1000)
- B (1) Removable, replacable filter 228058700 (installed)
- C (1) One-inch Neodymium Magnet equipped Drain Plug (installed)
- D (1) 1/8” NPT plug (installed)
INSTALLATION
- Step 1. Vehicle off and secure. Engine cool.
- Step 2. Remove crossmember.
- Step 3. Loosen stock pan bolts allowing fluidto carefully drain over the flange edge. Recycle fluid.
- Step 4. Remove pan. Retain stock gasket and stock flange collars.
- Step 5. Thoroughly clean stock gasket, collars, and housing mating surface.
- Step 6. Tighten PPE Filter screws and NPT Plug if necessary (B, D).
- Step 7. Install stock gasket on the PPE Transmission Pan flange. Install stock flange collars in the stock gasket.
- Step 8. Check for proper gasket alignment.
- Step 9. Install Pan to housing surface making sure the filter neck seats completely. Secure with two bolts through stock flange collars to hold Pan in
- place, finger tight for now.
- Step 10. Install remaining bolts.
- Step 11. Tighten in a crossing pattern as shown (Fig. 1). Final torque spec: 8-10 ft lbs.
- Step 12. Reinstall crossmember.
- Step 13. Add manufacturer-recommended fluid. Check for leaks.
Installation complete
When it’s timae to service, order your replacement PPE Transmission Fluid Filter (228058700) at PPEpower.com
DISCLAIMER OF LIABILITY
Performance products can increase horsepower above and beyond factory
specifications. Additional horsepower creates more stress on the drive-train
components, which could result in drive-train failure. Note regarding
emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE
LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR
REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE. This agreement sets forth
the terms and conditions for the use of PPE products. The installation of this
product indicates that the Buyer has read and understands this agreement and
accepts the terms and conditions. PPE (Pacific Performance Engineering) Inc.,
its distributors, employees, and dealers (the “Seller”) shall not be
responsible for the product’s proper use and service. The buyer hereby waives
all liability claims. The Buyer hereby acknowledges no reliance on the
Seller’s skill or judgment to select or furnish goods suitable for any
particular purpose and that there are no liabilities which extend beyond the
description on the face hereof, and the Buyer hereby waives all remedies or
liabilities expressed or implied, arising by law or otherwise (including
without any obligation of the Seller with respect to fitness, merchantability
and consequential damages), or whether or not occasioned by the Seller’s
negligence. The Seller disclaims any warranty and expressly disclaims any
liability for personal injury or damages. The Buyer acknowledges and agrees
that the disclaimer of any liability for personal injury is a material term
for this agreement and the Buyer agrees to indemnify the Seller and to hold
the Seller harmless from any claim related to the item of equipment purchased.
Under no circumstances will the Seller be liable for any damages or expenses
by reason of use or sale of any such equipment. The Seller assumes no
liability regarding the improper installation or misapplication of its
products. It is the installer’s responsibility to check for proper
installation and if in doubt, contact the manufacturer. The Buyer is solely
responsible for all warranty issues from the manufacturer.
LIMITATION OF WARRANTY
The Seller gives Limited Warranty as to description, quality, merchantability,
and fitness for a particular purpose, productiveness, or any other matter of
Seller’s product sold herewith. The Seller shall not be responsible for the
products proper use and service and the Buyer hereby waives all rights other
than those expressly written herein. This warranty shall not be extended,
altered or varied except by a written instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE
Transmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up-
Pipes Kits, and OEM-Length Up-Pipes. One (1) year limited warranty on all
other PPE products from the date of sale to original buyer and limited solely
to the parts contained within the products kit. All products that are in
question of Warranty must be returned prepaid to the Seller and must be
accompanied by a dated proof of purchase receipt. All Warranty claims are
subject to approval by Seller. Under no circumstances will the Seller be
liable for any labor charged or travel time incurred in diagnosis for defects,
removal, or re-installation – of this product or any other contingent
expenses. Under no circumstances will the Seller be liable for any damage or
expenses incurred by reason of the use or sale of any such equipment. In the
event that the buyer does not agree with this agreement: the buyer may
promptly return this product, in a new and unused condition in its original
packaging, with a dated proof of purchase to the place of purchase within ten
(10) days from date of purchase for a full refund. The installation of this
product indicates that the buyer has read and understands this agreement and
accepts its terms and conditions. PPEpower.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>