ioGiant MR1 4G LTE AC1200 Dual Band Wi-Fi Router User Guide
- June 8, 2024
- ioGiant
Table of Contents
ioGiant MR1 4G LTE AC1200 Dual Band Wi-Fi Router User Guide
Package contents
- 4G LTE Router x1
- Power adapter x1
- Ethernet cable x 1
- Quick installation guide x 1
- 4G LTE detachable antennas x 2
Set up the router
-
Attach the antennas to the router.
-
Insert a SIM card into the slot on the bottom panel of the router.
-
Use the included power adapter to connect the PWR jack of the router to a power source.
-
Press the ON/OFF button down to turn on the router.
Wait a few seconds until the LED indicator lights up, which indicates the router is Attach the antennas to the router is connected to the Internet successfully.
Tips: If the LED indicator does not light up, refer to Q1 in FAQ.
Access the Internet
- Connect your wired device, such as a computer, to the WAN/LAN or LAN port of the router using an Ethernet cable.
- Connect your wireless device, such as a smart phone, to the Wi-Fi network of the router using the Wi-Fi Name and Wi-Fi Key , which are printed on the label at the bottom of the router.
To further configure the router, log in to the Web UI of the router by visiting http://iogiantwifi.com on a connected device. You can also download the ioGiant WiFi APP on your smartphone to manage the router.
LED indicators
| LED indicator | Status | Description |
|---|---|---|
| UindicatorPower LED | Solid on | The router is powered on properly |
| Off | The router is powered off or not powered on properly. | |
| Internet LED indicator | Solid on | The router is connected to the Internet. |
| Of I | No Internet access is available. | |
| Wi-Fi LED indicator | Solid on | The Wi-Fi network is enabled. |
| Blinking | The router is ready for WPS negotiation. | |
| Off | The Wi-Fi network is disabled. | |
| LAN LED indicator | Solid on | At least one device is connected to a LAN port |
of the router.
Off| No device is connected to any LAN port of the router.
| Signal strength LED indicator| 3 bars| Excellent signal.
2 bars| Good signal.
1 bar| Fair signal.
Off| No signal.
Ports & Buttons
| Port/Button | Description |
|---|---|
| ON/OFF | Power button.Used to tum on or off the router. |
| PWR | Power jack.Used to cornett to a power source to supply power for the |
router.
RST/WPS| Used to reset the router, or start WPS negotiation of the router:
- Reset: Press ern hold the button fa 8 seconds mei all LEDimitators ight off and light up, then release the button. The router is restored to factory defeat setting.
- WPS: Through the WFS negotiation, you can connect your wireless devices to the Wi-Fi network without entering the Wi-Fi password.
Method: Press the button, and the Wi-Fl LED indicator blinks. Configure WPS-enabled wireless devices within 2 minutes to start WPS negotiation with the router.
WAN/LAN| It can serve as a WAN port or a LAN port.By default, the router is
under 3G/4G router mode and it serves as a LAN port. When the router is set to
the wireless router mode, or the Fa lover function Is enabled, it serves as a
WAN port.
LAN| It can serve as a LAN port or an IPTV port.When serving as a LAN port, It
can be connected to a computer, Ethernet switch or other LAN device.When the
IPTV function is enabled under the viceless router mode, it serves as the PTV
port to connect to the set-top box.
Antenna socket| Used to connect to the included antennas to enhance the 3G/4G
signal.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
This equipment should be installed and operated with minimum distance 20cm
between the device and your body.
Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operating frequency: 2412-2462MHz,5150-5250MHz,5725-5850MHz .
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures. This equipment should be installed and operated with minimum
distance 20cm between the device and your body.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.
Declaration of Conformity
Hereby, Shenzhen ioGiant Technology Co., Limited declares that the radio
equipment type MR1 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following Internet address: http://iogiant.vip/regulatory
-
Operating Frequency:
2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
5 GHz: EU/5150-5250MHz (CH36-CH48) -
EIRP Power (Max.):
2.4 GHz < 20dBm
5 GHz < 23dBm -
Software Version: V16.03.07. A
Caution:
Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
Adapter Model: BN073-A09009E,BN073-A09009B
Input: 100-240V AC 50/60Hz 0.4A
Output: 9V/1A
: DC Voltage
Operating Environment
- Temperature: 0°C-40°C
- Humidity: (10 – 90) 96RH, non-condensing
IC RSS warning
Industry Canada (RSS-Gen Issue 4)
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference;
- This device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement:
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your body.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
For EU/EFTA, this product can be used in the following countries:
| BE| BG| CZ| DK| DE| EE| IE| EL| ES| FR| HR| IT| CY| LV
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
LT| LU| HU| MT| NL| AT| PL| PT| RO| SI| SK| FI| SE| UK
Designed by: ioGiant Technology LLC in the U.S.A.
Manufacturer: Shenzhen ioGiant Technology Co., Limited
Address: The Sth Floor, HuaMei Building, No. 35, ZhenXingLu, LiCunSheQu,
HuaQiangBei Street, FuTian District, Shenzhen City, Guangdong, China,
ZIP Code 518031
URL: https://iogiant.com
Telephone: +86-15820572903
Technical Support Email: support@iogiant.com
Copyright
2021© ioGiant Technology LLC. All rights reserved. ioGiont is the trademark of ioGiant Technology LLC. All other brand names mentioned herein are the trademark or registered trademarks of their respective holders. App store logo is the trademark of Apple Inc. Specifications are subject to change without prior notice.
Authorized European Representative Information:
Name: Pegasus Trading GmbH
Address: Sperberweg 4G Neuss NRW 41468 Germany
Contact: Jacky Chen
Telephone No.: 004921313133726
E-Mail: info@pegasustrading.eu
Authorized U.K. Representative Information:
Name: APEX CE SPECIALISTS LIMITED
Address: 89 Princess Street, Manchester, M1 4HT, UK
Contact: Wells
Telephone No.: 00441616371080
E-Mail: info@apex-ce.com