DOG CARE TCO5 Dog Training System User Manual

DOG CARE TCO5 Dog Training System

Steps on how to use

1. Charge the collar and remote control with the included USB cable. Charging takes approximately 2 hours respectively.

2. Collar fitting: when wearing the collar, the tightness is at most fit if one finger can be inserted underneath. Make sure the electrodes on the collar are placed snugly against your dog’s skin.

3. Turn on the collar: hold the ON/OFF button for 1.5 seconds.
   Turn on the remote control: rotate the ON/OFF switch clockwise.
   

4. Security keypad lock: toggle it down to unlock, and up to lock.

5. Vibrate command: press the vibration button briefly, and the collar will vibrate once.

6. Beep command: press the beep button briefly, and the collar will beep once.

7. Static intensity adjustment: press and hold the LEVEL button while rotating the remote control switches to adjust the static intensity. Static command: press the static button briefly, and the collar will apply a static stimulation.

8. Channel switch: it is possible to train 3 dogs at the same time. Toggle the channel button to select which dog to train.

9. Pairing: refer to page #10 for more information.

COLLAR STATIC STIMULATION

When wearing the collar, it is most suitable if one finger can be inserted under it. Too tight is not good for your dog, but too loose will dull the static function for the electrodes cannot touch your dog’s skin.

Not Feeling the Static? Try These Solutions

1. If your dog has thick for, please separate the fur apart so that both electrodes can touch the skin.
2. Make sure protective silicone caps are off the electrodes. They can dull the static sensation sent to your dog.
3. Water can help conduct electricity. If you spray some water around the electrodes, the static function can work more effectively.
4. One last thing you can try is to shear the fur where both electrodes are touched.

In the Box

1. Remote control
2. Collar
3. USB charging cable
4. Lanyard
5. User manual

Remote Control & Collar

1. ON/OFF button & static intensity regulator
2. Antenna
3. Security keypad lock
4. CD display
5. Channel switching
6. Button
7. Static mode button
8. Vibrate mode button
9. Beep mode button
10. Static intensity adjustment button
11. Pairing button (reverse side)
12. LED indicator light
13. Charging port
14. ON/OFF button
15. Electrodes

Screen

1. Charge the devices for at least 2 hours respectively.
   • a. Remote control: charge the device until the battery icon on the display indicates full bars.
   • b. Collar: charge the device until the red LED turns green. When the red light flashes, it indicates a low battery.

Configuration static levels: press and hold the static intensity adjustment button and simultaneously slowly rotate the static intensity regulator until the digit on the screen reaches a suitable strength.

Adjust the static intensity on an individual basis. The sensitivity to static depends on your dog’s size, weight, amount of fur, and even skin condition .

Wearing the Collar

1. Make sure that the collar is powered off.
2. Have your dog stand in a balanced position on a flat, even surface.
3. Put the strap over your dog’s neck, centering the collar underneath its neck and making sure that the dog care logo is upright facing you.
4. Tighten the strap so that it fits snugly on your dog’s neck and should not be able to rotate around the neck. The tightness is at most fit if one finger can be inserted underneath.

NOTE: the collar should fit tightly and should not be able to rotate or slide on your dog’s neck. Your dog must be able to swallow food and water normally. You should observe your dog’s behavior to verify that the collar is not too tight.

Wiggle the collar to work the electrodes through the dog’s coat.

NOTE: The electrodes must have contact with the dog’s skin to be effective. If your dog has thick fur, please separate the fur at the electrodes with a comb to enable them to reach the skin.

When you are satisfied with the fit of the collar, you may want to adjust the excess strap length. After removing the collar, you can put the strap’s end back through the buckle, or trim away excess strap length and seal the strap’s end with a lighter or candle flame.

NOTE: remove the collar first.

The silicone caps are optional. The soft caps protect your dog from direct contact with metal electrodes which in some cases may cause discomfort. However, the silicone caps may dull the static sensation.

Training Modes

1. Vibration mode: press the vibrate button, and the collar will vibrate once; hold the button, and the vibration persists.
2. Sound mode: press the beep button, and the collar will give a beep Sound; hold the button, and the beep sound persists.
3. Static mode: press the static button, and the collar will give static stimulation. Holding the button is designed to be invalid as it is not recommended to have prolonged static stimulation to your dog.
4. Switching channel: toggle the channel switch button to choose which collar to control when matching multiple collars.

Pairing

The set of remote control and collar has been paired with channel #1 by the factory setting. To pair an extra collar, please follow the instructions below:

1. Toggle the channel switch button and select channel # 2 or #3. The channel display will show the selected channel number for the new collar.
2. Ensure the collar is turned off. Hold the ON/OFF button of the collar for 3 seconds until the LED indicator light on the collar flashes alternately in red and green.
3. Hold the pairing button on the remote control for 1.5 seconds. When the collar beeps, the pairing is completed.

Trouble Shooting

1. No display on the LCD display when the remote is turned on; unable to turn off remote
   • The operation function is abnormal. Press the pairing button and the LEVEL button at the same time to restart the remote control.
2. The remote/collar runs out of power quickly
   • Make sure the charger and the remote/collar are securely connected.
   • Charge the device for 2 hours or above.
3. Remote does not respond
   • Recharge the remote
   • Check the keypad lock, and unlock the remote. Pair the remote and collar again.
4. The Collar does not respond
   • Make sure the collar has been paired. Check the remote, making sure the collar is on the corresponding channel. Check the remote, making sure both the remote and collar have sufficient power
5. The training system has no effect on my dog Make sure the collar has been turned on, and the electrodes are placed snugly against your dog’s skin.
   • Try increasing the static level.
6. Training mode fails to sync up even in a very short distance
   • Make sure there is no strong signal interference in your surroundings. The remote’s range could fluctuate subject to obstacles, electromagnetic fields, or even stormy weather.
7. The collar beeps vibrate or apply static stimulation by itself occasionally or constantly
   • Make sure no button on the remote has been pressed or gotten stuck.
   • Pair the collar with the remote once again.

Please feel free to contact our support team via

[email protected]

Training Tips

1. The device is used for training dogs only: please do not use it for any other purposes.
2. Do not use the device on dogs aged below 6 months, old, pregnant, easily frightened, aggressive, in heat, or in inferior health conditions.
3. Use verbal commands first, and supplement with corrective stimulus only as needed. Be consistent with your verbal commands; use the same word every time. Work with your pet on one behavior at a time to avoid confusion and frustration. Rewarding your dog with food treats will usually help to achieve the best result.
4. Use as little stimulus as possible and only reinforce verbal commands when necessary. Do not overcorrect your dog.
5. For example, use the beep sound as a warning by pressing the beep button. The dog will become conditioned to the beep preceding the corrective stimulus and will soon learn to recognize the beep as a warning along with your verbal command.
6. Do not rely on this product solely to train your dog. Some dogs will not respond to this product. We cannot guarantee the effectiveness of this or any trainer on your dog.

lf your dog shows signs of growling, snarling, biting, or aggression while using the collar, discontinue use immediately and contact a professional trainer for advice.

Safety Guidelines

1. It is strictly prohibited to disassemble the collar in any situation. Doing so will likely compromise the waterproof function and thus void the product warranty.
2. To guarantee normal diving function, please insert the waterproof rubber charging lid in place.
3. Please use the remote control and the collar from the complete set. Do not use other products to match the collar.
4. If you want to test the product, please use professional testing apparatus. Do not test with hands, so as to avoid accidental injury.
5. If find water at the charging port, please wipe it dry before charging.
6. The collar is not a regular traction collar and not recommended to attach a leash to walk your dog. Doing so during pulling may hurt the dog due to protruding electrodes on the collar.
7. Do not put the collar on for over 12 hours, as it may cause rashes or discomfort to your dog’s skin.

Terms of Use and Limitation of Liability

1. Use of this product means you accept all the terms and conditions.
2. This product is a professional dog training device. You are not recommended to use this product if your dog is clever and less than 8 pounds in weight. If you’re not sure whether the product is suitable for your pet dog, please consult the professional handler or contact us.
3. This product is a professional dog training device and cannot be used for other purposes. Please do not violate local laws by using this product.
4. We are not responsible for any direct or indirect damages caused by the use or misuse of this product; all risks in using this product are the responsibility of the user.
5. Please contact the dealer for parts warranty, goods return, or exchange. We provide technical support only.
6. We reserve the right to change the terms, conditions, and notices of this product are offered.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
3. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Product Specifications

FAQ’s

Why is the collar beeping?

The collar will beep when it is turned on and the battery is low.

Why does the remote control not work?

Make sure the remote control is within range of the collar.

Why does the remote control not work after pairing?

Make sure to press and hold the PAIRING button for 3 seconds.

Why does the remote control not work after pairing?

Make sure to press and hold the PAIRING button for 3 seconds.

The shock collar’s range is something I wish to know. I want to take my dog for some training in the great outdoors.

You may train your dogs anywhere with a remote dog training collar because its range is up to 330 yards (1000 feet).

The remote does have a strap? Or is it required that you have it in your hand or pocket?

Yes, the remote may be attached to your vest, etc., using a cute little strap.

The collar automatically shuts off; why? There is still power there.

Since it is a training collar, our program has it programmed to turn off automatically after several hours of inactivity.

The remote does have a strap? Or is it required that you have it in your hand or pocket?

Yes, the remote may be attached to your vest, etc., using a cute little strap.

Is the TC01 shock collar better suited to little dogs than this one? My corgi is a year old.

Yes. This collar is better suited for little dogs, and it also has a smaller remote than the TC01 collar.

Is this training collar for dogs weatherproof?

Dog training collars are indeed waterproof. Although the receiver is composed of waterproof materials, the charging port could become lost while in use. Therefore, please make sure the receiver charging port is properly closed before it comes into touch with water. in order to prevent water from entering the receiver.

When fastened, the collar sags. Very erratic corrections—or none at all—are the end outcome at the selected level. searching for a replacement collar buckle.

It hasn’t happened to me. I’m incredibly pleased with everything, including the build. The on/off button broke after being bitten by another dog, which was unfortunate for us. The collar was purchased jointly.

Does it also have a bark collar? Will it repair itself or do you have to press a button?

You’d need to press the button.

Video

Download PDF MANUAL: DOG CARE TCO5 Dog Training System User Manual

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>