i Safe MOBILE IS530.1 M53A01 Rugged Smartphone User Manual

: June 8, 2024
: i safe MOBILE

Table of Contents

i Safe MOBILE IS530.1 M53A01 Rugged Smartphone
DEVICE OVERVIEW/FUNCTIONS
FIRST
SAFETY
DEVICE OVERVIEW/FUNCTIONS
PREPARATION
CHARGING
MAINTENANCE/REPAIR
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

i Safe MOBILE IS530.1 M53A01 Rugged Smartphone

DEVICE OVERVIEW/FUNCTIONS

Document No. 1029MM01REV08
Version : 2022-10-31
(c) 2022 i.safe MOBILE GmbH i.safe MOBILE GmbH i_Park Tauberfranken 10 97922 Lauda-Koenigshofen Germany
Tel. +49 9343 60148-0
info@isafe-mobile.com
www.isafe-mobile.com

FIRST

This Quick Start Manual contains all the important health and safety instructions for using the device IS530.1 (Modell M53A01) safely.
Read the “Safety” section of this Quick Start Manual carefully before using the device. If you do not follow these instructions or do not understand them, this could lead to death, severe injuries and damage to the device.
Read the Operating Manual before using the device.
The Operating Manual with detailed information and instructions concerning the device can be found at www.isafe-mobile.com/en/support/downloads
Also read the Safety Instructions before using the device. These can be found in the device packaging and at www.isafe-mobile.com/en/support/downloads
Follow all instructions given on the device and on the packaging.
Follow local safety regulations.

SAFETY

USE IN EXPLOSION HAZARDOUS AREAS

Only use the device in explosion hazardous areas of zones 1/21 and 2/22 or outside of explosion hazardous areas.
Before entering an explosion hazardous area with the device,
- make sure that only approved accessories are connected to the device, see section “Connecting approved accessories”,
- make sure that no gap can be seen between the two halves of the device,
- make sure the device is not damaged,
- make sure that all the labels on the device are readable,
- make sure the battery is screwed tight.
If you use the device in an explosion hazardous area,
- do not loosen the screws on the device,
- do not connect any accessories to the device,
- do not open any interface cover,
- do not charge the device,
- do not open the device,
- do not damage the device.
Switch off the device immediately and leave the explosion hazardous area without delay if
- malfunctions occur on the device,
- you have damaged the housing of the device,
- you have exposed the device to excessive loads,
- the labels on the device are no longer readable.

USE OUTSIDE OF EXPLOSION HAZARDOUS AREAS

Do not modify the device structurally.
Do not expose the device to high temperatures.
Do not expose the device to strong UV radiation.
Do not expose the device to processes with high electrical charges.
Do not expose the device to aggressive acids or bases.
Do not use the device in places where its use is prohibited.
Turn off the device in clinics or other medical facilities.
Always keep a safety distance of at least 15 cm between the device and a pacemaker or hearing aid. The device can affect the functioning of medical devices such as pacemakers and hearing aids.
When using the device while driving a motor vehicle, be sure to comply with applicable national laws.

WHEN USING EARPHONES OR HEADSETS

First set the volume control on the device to 50 % of the maximum volume.
Gradually adjust the volume

DEVICE OVERVIEW/FUNCTIONS

(see illustration on page 2)

STATUS LED: Display for notifications and charging status.
SOS KEY: A long press of the SOS key sends an emergency call to a pre-saved emergency number (only in connection with a Lone Worker Protection app).
LOUDSPEAKER
POWER KEY: A long press switches the device on/off. A short press switches the standby mode on/off.
FRONT CAMERA
ISM INTERFACE: Connection for approved accessories. Also see section “Connecting approved accessories”.
MAGNETIC CHARGER PORT: Connection for the i.safe PROTECTOR 3.0 Magnetic Charger Cable. Also see section “Charging”.
SIDE KEY RIGHT: Optional function, e.g. camera – function can be assigned via Button App (system integrated).
CURRENT APPLICATION: Shows all open applications.
HOME KEY: Switch to the main screen.
BACK KEY: Go to the previous screen.
USB INTERFACE: Connection for the i.safe PROTECTOR 2.0 USB-C Cable or for connection to other devices. Also see sections “Charging” and “Connecting approved accessories”.
MICROPHONE
LOUDNESS CONTROL: Volume up/Volume down.
SIDE KEY LEFT: Optional function – function can be assigned via Button App (system integrated).
SENSORS: Proximity sensor, light sensor.
LED FLASH
NOISE CANCELLING: Noise cancelling microphone.
LOUDSPEAKER: Loudspeaker for hands-free function.
BACK CAMERA
BATTERY

PREPARATION

The device has two slots for one SIM card each and one slot for a microSD card up to a size of 128 GB. The slots are located in the battery compartment and are marked “SIM 1“, “SIM 2“ and “microSD“.
Insert the SIM card into the slot.
Insert the microSD card into the slot provided.
Place the battery in the battery compartment.
Hand-tighten the screws using the Torx Screwdriver provided.
Check that the battery is seated correctly and securely

SWITCHING ON

Press and hold the on/off key for about 3 seconds.
When turning on the device for the first time, follow the instructions on the screen.
Enter the device or SIM PIN when the input dialog for the device or SIM PIN appears after switching on.
If you have inserted two SIM cards, select a favorite card. Information on operating the device can be found at www.isafe-mobile.com/en/support/service under the menu item “FAQ“.

CHARGING

Only charge the device outside of explosion hazardous areas.
Only charge the device using the i.safe PROTECTOR 2.0 USB-C Cable supplied or with the i.safe PROTECTOR 3.0 Magnetic Charger Cable supplied.
Do not charge the device in the vicinity of flammable substances.
Only charge the device at ambient temperatures between +5 °C to +35 °C (+41 °F to +95 °F).
Charge the device under dry indoor conditions only.
Do not charge the device in environments dusty or humid.
Connect the adapter suitable for your country to the power supply unit.
Connect the i.safe PROTECTOR 2.0 USB-C Cable or the i.safe PROTECTOR 3.0 Magnetic
Charger Cable to the power supply unit.
Connect the i.safe PROTECTOR 2.0 USB-C Cable to the USB interface of the device, or connect the i.safe PROTECTOR 3.0 Magnetic Charger Cable to the magnetic charging port on the device.

CONNECTING APPROVED ACCESSORIES

Only connect accessories approved by i.safe MOBILE to the device. Accessories approved by i.safe MOBILE can be found at www.isafe-mobile.com/en/products
Connect approved accessories to the ISM interface of the device only outside of explosion-hazardous areas.
Operate approved accessories in explosion-hazardous areas only on the ISM interface of the device. Wired connections via the USB interface are prohibited.
Connect the plug of the accessory securely to the ISM interface of the device and check that the plug is seated correctly and securely before entering explosion hazardous areas.
Close the ISM interface with the cover provided when you are not using accessories.
Only use USB interface outside of explosion hazardous areas.
You should never open the cover of the USB interface in explosion-hazardous areas

Approved accessories can be connected to any ISM interface and to the USB interface.

Loosen the screw on the ISM interface cover using the Screwdriver included in the accessory package and remove the cover as shown.
Connect the plug of the approved accessory to the ISM interface as shown.
Hand-tighten the screws.
Check that the plug is seated correctly and securely.

The USB interface is used for charging and data transfer.

Connect approved accessories or other devices to the USB interface only by using the i.safe PROTECTOR 2.0 USB-C Cable.

MAINTENANCE/REPAIR

Contact the i.safe MOBILE repair service at www.isafe- mobile.com/en/support/service if the device is not working normally, if the device needs to be repaired or if a replacement part is required.

RETURN SHIPMENT

Contact the i.safe MOBILE repair service at www.isafe- mobile.com/en/support/service

CLEANING

Turn off the device before cleaning.
Do not charge the device while cleaning.
Do not use chemical agents for cleaning.
Clean the device and the Power Adapter with a soft, moistened antistatic cloth.
Clean the display screen regularly with a soft, antistatic cloth

STORAGE

Store the device at ambient temperatures between +5 °C to +35 °C (+41 °F to +95 °F) and a humidity between 10 % to 60 %.

RECYCLING

DO NOT throw away batteries with household waste.
Always dispose electronic products, batteries and packaging material at the appropriate collection points. This way, you prevent uncontrolled waste disposal and promote the recycling of material resources.
You can obtain further information from regional waste disposal companies, state authorities or the i.safe MOBILE service centre responsible for your country or region at www.isafe-mobile.com/en/support/service

TRADEMARKS

i.safe MOBILE and the i.safe MOBILE logo are registered trademarks of i.safe MOBILE GmbH.
EEA Version: Comes with the Google™ app and Google Chrome™
Google and Google Play are trademarks of Google LLC.
All other trademarks and copyrights are the properties of their respective owners

CONTACT/SERVICE CENTRE

FOR FURTHER QUESTIONS PLEASE CONTACT OUR SERVICE CENTRE: i.safe MOBILE GmbH, i_Park Tauberfranken 10, 97922 Lauda-Koenigshofen, Germany
support@isafe-mobile.com
https://support.isafe-mobile.com
WWW.ISAFE-MOBILE.COM