AMEWi Mercedes truck tipper PRO metal 2.4GHz RTR white Instructions

AMEWi Mercedes truck tipper PRO metal 2.4GHz RTR white

Declaration of Conformity

• This product has been manufactured according to actual technical standards. The product is matching the requirements of the
  existing european and national guidelines. The Declaration of Conformity has been proofed. AMEWI TRADE GmbH declares that this product is matching the basic requirements and remaining regulations of the guideline 2014/53/EU (RED).

• The declarations and documents are stored at the manufacturer and can be requested and applied there.

• The full text of the declaration of conformity can be found at: https://amewi.com/Konformitaetserklaerungen

• For additional questions to the product and conformity please contact:

  • AMEWI TRADE GmbH Nikolaus-Otto-Str. 18, 33178 Borchen or via the website amewi.com

Security and Hazard Warnings

• Warning! For damage, caused by disregarding of the manual, warranty expires! We are not liable for secondary failures, material or personal damage, caused by inproper usage or disregarding the security notices.
• Warning! Based on security and registration (CE) reasons, it is forbidden to modify the product personally. Do not disassemble the product.
• Warning! Small parts. Danger of suffocation or risk of injury caused by small parts.
• The product is not allowed to get moist or wet. The product is only allowed to be used on flat and clean surfaces.
• Even a drop down from a small height can cause damage to the product.

Battery Notice and Battery Disposal

Warning! Battery do not belong in childrens hands. A change of the battery has to be done by an adult person. Never mix chargable batteries with non-chargable batteries. Never mix fully charged batteries with almost emtpy batteries. Never mix batteries of different capacities. Never try to charge dry batteries. Take care of the correct polarity. Defective batteries belong to special waste. Never leave a charging battery unattended. For questions about the charging time please read the manual or ask the manufacturer.

DISPOSAL

• The company AMEWI is registered below the WEEE Reg. Nr. DE93834722 at the foundation EAR and recycles all used electronic parts properly. Electric and electronical products are not allowed to put in household garbage.
  Please dispose the product at the end of the lifetime accroding to the actual laws. You as a customer are responsible by law for the return of all used batteries, a disposal over the household garbage is forbidden!

• Batteries containing hazardous substances are marked with the alongside symbols, which point to the prohibition of disposal in household garbage.

• Additional notations for the critical heavy metal are: Cd=Cadmium, Hg=Quecksilver, Pb=lead (Label is placed on the batteries, for example below the bottom left trash symbols).

• Based on RoHS labeling the manufacturer confirmes, that all limit values were taken care of at the time of manufacturing.

• Batteries labeled with the recycling symbol can be put into used battery collecting tank. (Most supermarkets have)

• They are not allowed to be put into local household garbage.

• AMEWI is involved in the dual system for boxing over the company Firma Landbell AG.

• All used bOxes are collected from partner companies (waste disposal contractor) at private custo mers (local household), sorted and properly utilized. The Involvement in a Dual Systems helps to save CO* Emissions

Installation of setting battery in truck

1. Loosen screw of battery cover by screwdriver, twist the buckle and take out battery cover.(Pic.1)

2. Connect rechargeable battery with power port of truck, then put it into the battery box.(Pic .2)

3. Install the battery cover, tighten the screw and twist the buckle back.(Pic.3)

BATTERY CHARGING INSTRUCTION

CHARGING METHODS
Connect the white port of Li-lon to USB charging port, as shown in the Figure, and ensure port can be connected tightly and correctly, then insert the USB charging plug into power adapter, and perform charging.

BATTERY/USS PARAMETERS

Battery specifications: 18650

7.4V 2000mAh

Intelligent USB balance charger with overcharge protection

Input: 5.0V 1-2A

Output:4.2V 800mAh X2

INDICATOR LIGHT STATUS AT THE TIME OF CHARGING:

• Uncharged state: red light alwayslit

• Charged state:
  Red light always lit + Green light flashes

• Full charging state:
  Red and green light always lit

• Charging period: 5-7 hours
  When battery is charged, please pull off the USB charger lead in time.

INSTALLATION OF REMOTE BATTERY

1. Loosen the screw of battery cover by screwdriver and take out battery cover. (Pic .1)
2. Put four 1.5V “AA “non-rechargeable batteries (batteries need to be purchased separately) into the battery box to the right polarity at the bottom of remote control. (Pic .2)
3. Install the battery cover and tighten the screw. (Pic .3)

Operation of remote control

The match of R/C frequency and power on

This product is controlled by the frequency of 2.4GHz. When playing it at the first time, please turn on the power and wait for the automatically matching of frequency. The sound “‘beeps” given by the product indicates that the frequency is matched successfully.

Control of light and sound

• Press this button to turn on the sound, and press once more to turn it off.

• Press this button to turn on the light, and press once more to turn it off.

The operation of front wheel

When the car can’t go straightly, please control the wheel to the left or right fine tuning.

Rectification of deviation to the left

Rectification of deviation to the Right

Operation of playing the truck

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>