i safe MOBILE M53A01 4G Smartphone Instruction Manual
- June 8, 2024
- i safe MOBILE
Table of Contents
I safe MOBILE M53A01 4G Smartphone
PRODUCT COMPLIANCE FOR NORTH AMERICA
Conforms to:
STD UL 62368-1, STD UL 913
Certified to:
CSA STD CSA C22.2#60079-0, CSA STD CSA C22.2#60079-11, CSA STD CSA
C22.2#62368-1
EX-RELEVANT SAFETY REGULATIONS
Use of this device assumes that the operator observes the conventional safety
regulations and has read and understood manual, safety instructions and
certificate.
The following safety regulations must also be complied with:
-
Inside ex-hazardous areas the covers of all interfaces must be closed.
-
To ensure the IP-protection, it has to be ensured that all gaskets are present and functional. There must be no large gap between the two halves of the housing.
-
The device may only be charged outside ex-hazardous areas using the i.safe PROTECTOR 2.0 or i.safe PROTECTOR 3.0 USB-cable or other equipment approved by i.safe MOBILE GmbH.
-
When using the IS-HS1.1 headset, the headset must be securely fastened to the ISM interface.
-
Physical connections to equipment other than the IS-HS1.1 headset are only allowed outside ex-hazardous areas using the i.safe PROTECTOR 2.0 and i.safe
-
PROTECTOR 3.0 USB-cable or other equipment approved by i.safe MOBILE GmbH.
-
The device may only be charged at ambient temperatures between +5°C … +35°C.
-
The device may not be exposed to any aggressive acids or alkalis. The device may only be used in zones 1, 2, 21, or 22.
Only accessories approved by i.safe MOBILE GmbH may be used. -
EX-RELEVANT SAFETY REGULATIONS FOR NORTH AMERICA
-
Conditions of Acceptability:
-
The battery shall only be charged outside the explosion hazardous areas only and using a suitably certified Class 2 power supply with the following output parameters:
V = 5VDC I = 2000mA. -
The smartphone must be protected against excessive UV light emission and high electrostatic processes.
-
The USB interface (type C) located at the bottom side is for data transmission and it is used in non hazardous areas. It is not permitted to open the USB interface cover in hazardous locations.
-
The ISM interface of the IS530.1 located at the right side can be used within hazardous areas with approved headsets, Remote Speaker Microphones(RSM) and add-ons.
-
For the ISM interface connection the intrinsically safe approved accessories must comply with entity parameters according to document 1029AD04 i.e. Headset IS-HS1.1 is approved to be used on ISM interface. If the ISM interface is not used, it must be securely closed by the cover provided for this purpose.
-
Unauthorized repair is not allowed.
-
Apparatus is for use in pollution degree 2 or better.
-
Only designated charger may be connected to the charging contacts.
-
Not suitable for hazardous locations when enclosure is damaged.
-
Enclosure rating: IP64
FAULTS AND DAMAGES
If there is any reason to suspect that the safety of the device has been compromised, it must be withdrawn from use and removed from any ex-hazardous areas immediately. Measures must be taken to prevent any accidental restarting of the device. The safety of the device may be compromised, if, for example:
- Malfunctions occur.
- The housing of the device shows damage.
- The device has been exposed to excessive loads.
- The device has been stored improperly
- Markings or labels on the device are illegible.
- We recommend that a device displaying errors or in which an error is suspected be sent back to i.safe MOBILE GmbH to be checked.
Restrictions in the 5 GHz band:
According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that
this radio equipment will be subject to some restrictions when placed on the
market in Belgium (BE),-Bulgaria (BG), the Czech Republic (CZ),Denmark (DK),
Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain(ES), France (FR),
Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania(LT), Luxembourg
(LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria(AT), Poland (PL),
Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK),Finland (FI), Sweden
(SE), the United Kingdom (UK), Turkey (TR), Norway(NO), Switzerland (CH),
Iceland (IS), and Liechtenstein (LI). The WLAN function for this device is
restricted to indoor use only when operating in the 5150 to 5350 MHz frequency
range.
| AT| BE| BG| CH| CY| CZ| DE
---|---|---|---|---|---|---|---
DK| EE| EL| ES| FI| FR| HR
HU| IE| IS| IT| LI| LT| LU
LV| MT| NL| PL| PT| RO| SE
SI| SK| TR| UK| | |
EU/UK DECLARATION OF CONFORMITY
according to directive 2014/34/EU, SI 2016 No. 1107, 2014/53/EU, SI 2017 No.
1206, 2011/65/EU (2015/863/EU), SI 2012 No. 3032 nach Richtlinie 2014/34/EU,
2016 No. 1107, 2014/53/EU, SI 2017 No. 1206, 2011/65/EU (2015/863/EU), SI 2012
No. 3032
The company i.safe MOBILE GmbH declares under its sole responsibility that the
product to which this declaration relates is in accordance with the provisions
of the following data, directives, and standards:
Name & address of the manufacturer in the EU Name & Anschrift des Herstellers innerhalb der europäischen Gemeinschaft| i.safe MOBILE GmbH i_Park Tauberfranken 10
97922 Lauda – Koenigshofen
Germany
---|---
Description of the devices
Beschreibung der Geräte
| Explosion protected smartphone Explosionsgeschütztes Smartphone type / Typ : IS530.1 & IS-HS1.1
model / Model : M53A01
Ex – marking
Ex – Kennzeichnung
| II 2G Ex ib IIC T4 Gb
II 2D Ex ib IIIC T135°C Db IP6X
Type examination certificate 2014/34/EU issued by
Baumusterprüfbescheinigung 2014/34/EU ausgestellt durch
| EPS 19 ATEX 1 037 X
__
Bureau Veritas Consumer Products Services Germany GmbH
Oehleckerring 40
22419 Hamburg, Germany
identification number / Kenn-Nummer : 2004
Applied harmonized standards
Angewandte harmonisierte Standards
| __
EN IEC 60079-0:2018; EN60079-11:2012
Type examination certificate SI 2016 No. 1107
issued by
Baumusterprüfbescheinigung SI 2016 No. 1107 ausgestellt durch
| CML 21UKEX2489X
__
Erofins E&E CML Limited,
Newport Business Park, New Port Road, Ellesmere Port,
CH65 4LZ, United Kingdom
identification number / Kenn-Nummer : 2503
Applied standards
Angewandte Standards
| EN IEC 60079-0:2018; EN60079-11:2012
Conformity statement 2014/53/EU| PHOENIX TESTLAB GmbH
---|---
issued by| Koenigswinkel 10
Konformitätsaussage 2014/53/EU ausgestellt| 32825 Blomberg
durch| Germany
| identification number / Kenn-Nummer : 0700
Applied harmonized standards| EN 62368-1:2014+A11:2017;
Angewandte harmonisierte Standards| EN 50332-1:2013; EN 50332-2:2013;
| EN 50360:2017; EN 50566:2017;
| EN IEC 62311:2020; EN 62479:2010;
| EN 50663:2017; EN 62209-1:2016;
| EN 62209-2:2010+A1:2019;
| ETSI EN 301 489-1 V2.2.3;
| ETSI EN 301 489-3 V2.1.1;
| ETSI EN 301 489-17 V3.2.4;
| ETSI EN 301 489-19 V2.1.1;
| Draft ETSI EN 301 489-52 V1.1.0;
| EN 55032:2015+A11:2020;
| EN 55035:2017+A11:2020;
| ETSI EN 301 511 V12.5.1;
| ETSI EN 301 908-1 V13.1.1;
| ETSI EN 301 908-2 V13.1.1;
| ETSI EN 300 328 V2.2.2;
| ETSI EN 301 893 V2.1.1;
| ETSI EN 300 440 V2.2.1;
| ETSI EN 300 330 V2.1.1;
| ETSI EN 303 413 V1.1.1
Conformity statement SI 2017 No. 1206 issued| MiCOM Labs Inc.
by| 575 Boulder Court,
Konformitätsaussage SI 2017 No. 1206| Pleasanton, California 94566
ausgestellt durch| USA
| identification number / Kenn-Nummer : 2280
Applied standards| EN IEC 62368-1:2014+A11:2017;
Angewandte Standards| EN 62209-1:2016;
| EN 62209-2:2010/A1:2019
| EN 50360:2017; EN 50566:2017;
| EN 50663:2017; EN 50332-1:2013;
| EN 50332-2:2013; EN IEC 62311:2020;
| EN 62479:2010; Draft EN 301 489-52 V1.1.0;
| EN 301 489-19 V2.1.1; EN 301 489-17 V3.2.4;
| EN 301 489-3 V2.1.1; EN 301 489-1 V2.2.3;
| EN 55032:2015+A11:2020;
| EN 55035:2017+A11:2020;
| EN 300 328 V2.2.2;
| EN 301 893 V2.1.1; EN 300 440 V2.2.1;
| EN 303 413 V1.2.1; EN 301 511 V12.5.1;
| EN 301 908-1 V13.1.1; EN 301 908-2 V13.1.1;
EN 301 908-13 V13.1.1; EN 300 330 V2.1.1;
---|---
Conformity statement 2015/863/EU amending| SGS-CsTC Standards Technical
Services Co.,
2011/65/EU issued by| Ltd.
Konformitätsaussage 2015/65/EU ergänzt| 198 Kezhu Road,
2011/65/EU ausgestellt durch| Scientech Park Guangzhou Economic &
| Technology Development District,
| Guangzhou, China 510663
Applied harmonized standards| IEC 62321-2: 2013; IEC 62321-1: 2013;
Angewandte harmonisierte Standards| IEC 62321-3-1: 2013; IEC 62321-5:
2013;
| IEC 62321-4: 2013 + A1: 2017;
| IEC 62321-7-1: 2015;
| IEC 62321-7-2: 2017 & ISO 17075-1: 2017;
| IEC 62321-6: 2015;
| IEC 62321-8: 2017
Conformity statement SI 2012 No. 3032 issued| SGS-CsTC Standards Technical
Services Co.,
by| Ltd.
Konformitätsaussage SI 2012 No. 3032| 198 Kezhu Road,
ausgestellt durch| Scientech Park Guangzhou Economic &
| Technology Development District,
| Guangzhou, China 510663
Applied standards| IEC 62321-2: 2021; IEC 62321-1: 2013;
Angewandte Standards| IEC 62321-3: 2013; IEC 62321-5: 2013;
| IEC 62321-4: 2013 + A1: 2017;
| IEC 62321-7-1: 2015; IEC 62321-7-2: 2017;
| IEC 62321-6: 2015; IEC 62321-8: 2017;
| ISO 17075-1:2017
CE/UKCA Marking
CE/UKCA- Kennzeichnung
|
- Lauda – Koenigshofen 06.10.2022
- Dirk Amann
- Managing Director
- Geschäftsführer
- WWW.ISAFE-MOBILE.COM
- Document No. 1029MM11REV03 Version: 2022-12-21 (c) 2022 i.safe MOBILE GmbH i.safe MOBILE GmbH i_Park Tauberfranken 10 97922 Lauda-Koenigshofen
- Germany
- Tel. +49 9343 60148-0
- info@isafe-mobile.com
- www.isafe-mobile.com
EX MARKINGS
- ATEX:
- II 2G Ex ib IIC T4 Gb
- II 2D Ex ib IIIC T135°C Db IP6X EU Type
- Examination Certificate: EPS 19 ATEX 1 037 X
- CE-designation: 2004
- IECEx:
- Ex ib IIC T4 Gb
- Ex ib IIIC T135°C Db IP6X
- IECEx Certificate: IECEx EPS 19.0014X
- SANS:
- Ex ib IIC T4 Gb
- Ex ib IIIC T135°C Db IP6X
- SANS Certificate: MTEx-S/20.0011 X
- UK:
- II 2G Ex ib IIC T4 Gb
- II 2D Ex ib IIIC T135°C Db IP6X
- CML 21UKEX2489X
- UKCA-designation: 2503
- North America:
- Class I Div 1 Groups A, B, C, D, T4 Class II Div 1 Groups E, F, G , T135˚C Class III Div 1 CSA19CA70220251X
- Temperature range: – 20°C … +60°C (EN/IEC 60079-0) – 10°C … +50°C (EN/IEC 62368-1) Manufactured by:
- i.safe MOBILE GmbH i_Park Tauberfranken 10 97922 Lauda-Koenigshofen Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>