twinkly LED Light Strip User Manual

: June 8, 2024
: Twinkly

Table of Contents

LED Light Strip
Use and care instructions
physical set-up
controller
app download
setup twinkly
connection modes
mapping
troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GENERATION II
flex
LED Light Strip
User Manual

LED Light Strip

attention
Read and follow all safety instructions.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
This seasonal use product is not intended for permanent installation or use.
Do not mount or place near gas or electric heaters, fireplaces, candles, or other similar sources of heat.
Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
Do not let lamps rest on the supply cord or on any wire.
Unplug the product when leaving the house, or when retiring for the night, or if left unattended.
This is an electric product — not a toy! To avoid the risk of fire, burns, personal injury, and electric shock it should not be played with or placed where small children can reach it.
Do not use this product for other than its intended use.
Do not hang ornaments or other objects from the cord, wire, or light string.
Do not cover the product with cloth, paper, or any material not part of the product when in use.
Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS.
Do not connect the chain to the supply while it is in the packing.
Where breakage or damage to lamps occurs the chain must not be used/energised but disposed of safely.
The lamps are not replaceable.
WARNING – RISK OF ELECTRIC SHOCK IF LAMPS ARE BROKEN OR MISSING. DO NOT USE.

Use and care instructions

a. The external flexible cable or cord of this light fixture cannot be replaced. If the cord is damaged, the light fixture should be disposed of.
b. The light source of this light fixture is not replaceable. When the light source reaches the end of its life, the whole light fixture should be replaced.
c. FOR INDOOR USE ONLY
d. Do not connect the rope light to the power supply while it is in the packing or wound on a reel.
e. Do not use the rope light when covered or recessed into a surface.
f. Do not open or cut the rope light
WARNING – To reduce the risk of fire and electric shock:
a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal.
b. Do not mount or support wires in a manner that can cut or damage wire insulation.
Class A Disclaimer: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.

WARNING!
Do not connect the light string to the power supply while it is in the packaging. The connecting cable cannot be repaired or replaced. THE LAMPS ARE NOT REPLACEABLE. The lighting chain must not be used without all gaskets being in place. Lighting chains don’t intend for interconnection.
Do not connect this light string electrically to devices from another manufacturer.
CAUTION!
Strangulation hazard. Keep out of reach of young children.
** The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal.
The manufacturer, Ledworks Srl, declares that this device complies with the (LVD) 2014/35/EU, (RED) 2014/53/EU, (EMC) 2014/30/EU, (RoHS) 2011/65/EU, (REACH) 1907/2006 directives. The full text of the EU declaration of conformity is available at the following Internet address: www.twinkly.com/certifications
System Requirement
The minimum system requirement for mobile phones are iOS 11 and Android 5 Check the app store for the latest update to ensure the best performance.
Technical Specifications
Power supply: see label
IP protection: IP20
Premium grade LED diodes**
To ensure high color rendering, Twinkly products only use high-quality LEDs.
Twinkly’s RGB and RGB+W products are produced according to quality principles and processes that allow us to obtain a high degree of primary color purity.
The minimum excitation purity values of the Blue, Green and Red components are shown within the table below.

Operating RF for Wi-Fi / Bluetooth

Frequency| 2402/2480 Mhz
Max output|
Power| <100mW
Color Purity values

Blue| > 90%
Green| > 65%
Red| > 95%

values apply only to RGB (STP) and RGBW (SPP) products, not AWW (GOP) products

physical set-up

twinkly LED Light Strip - Figure 1

Use the drawing guidelines provided to mark the positions of the mounting clips on the surface to which you want to attach Flex or draw your own shape.
Drill holes where the marks for the mounting clips are located, then position the mounting clips provided. Use fasteners suitable for your surface (not supplied).
Attach Flex to the surface using the mounting clips.
Use the supplied adhesive cable clips to keep the cable stable and organised.
Insert the plug into the power adapter and connect to a power source. The lights will turn on automatically.

controller

CONTINUOUS GREEN: Direct Wi-Fi mode, connected
FLASHING GREEN: Direct Wi-Fi mode, no device connected
CONTINUOUS BLUE: Home Wi-Fi network mode, connected
FLASHING BLUE: Home Wi-Fi network mode, connection in progress
FLASHING RED: Home Wi-Fi network mode, unable to connect
LIGHT BLUE: SETUP MODE (Bluetooth ON)
YELLOW: Firmware Update in progress
CONTINUOUS RED: General error

twinkly LED Light Strip - Figure 3

app download

http://twinkly.com/manual

Go to App Store/Google Play Store (or scan QR code).
Download and install the Twinkly app
Note: All app illustrations in this document are a mere representation of the functionality and might vary from the actual app visuals.

setup twinkly

twinkly LED Light Strip - Figure 4

Launch Twinkly app.
Sign up/log in to your account (necessary for using smart home features).
Follow the setup process on the app.

connection modes

Twinkly uses Bluetooth for the setup process only. Wi-Fi connection is required for operation. You can use:
A. Home Wi-Fi network connection (recommended): Connect with your home/office WiFi from the list of available networks.
B. Direct Wi-Fi connection: Select “Twinkly_xxxxxx” WiFi from the list of available networks. Password: Twinkly2019
( NOTE: the internet on your phone will not be available in this case)
A. HOME WI-FI NETWORK CONNECTION

B. DIRECT Wi-Fi CONNECTION

mapping

|
---|---

Map the layout of your decoration to unlock the full potential of your Twinkly lights, such as advanced effects, drawing, and many upcoming features. mapping tips

| twinkly LED Light Strip - Figure 11
---|---

Note: For best results, avoid reflective surfaces behind the tree, keep the mobile cam steady during the process, and ensure moderate ambient light (not too dark).

troubleshooting

Q THE LIGHTS DO NOT SWITCH ON

Check that the power adapter is plugged in and that the controller is correctly connected to the device
Check that the LED status indicator on the controller is lit
Briefly press the button on the controller
If this doesn’t work, unplug the power adapter, wait 30 seconds and plug in again

Q THE LIGHTS TURNED ON BUT ARE BLOCKED

Briefly press the button on the controller
If this does not work, unplug the power adapter, wait 30 seconds and plug it in again

reset twinkly

twinkly LED Light Strip - Figure 12

Unplug Twinkly from the power socket. Press and hold the controller button.
While holding the button, plug in Twinkly.
Keep holding the button until all LEDs turn red (or amber for Gold Edition), then release the button.

online manual

| Browse, play and edit effects.
---|---
| Create new effects.
| Group multiple devices together.
**| Synchronize with music.
| Download new effects.
| Control with Smart Home Assistant.**

For all these features and more, see help.twinkly.com

RGB