SCHIIT BIFROST 2 True Multibit Autonomy DAC with Unison Usb Owner’s Manual
- June 4, 2024
- SCHIIT
Table of Contents
BIFROST 2 True Multibit Autonomy DAC with Unison Usb
**Owner’s Manual
**
IN NORSE LEGEND, BIFROST IS THE FLAMING RAINBOW BRIDGE CONNECTING ASGARD TO MIDGARD (AKA, THE EARTH). YES, RAINBOWS, HOW THE 1970S OF THEM, HA HA. TELL THAT TO ODIN AND SEE WHAT HE THINKS. I DON’T THINK YOU’LL BE LAUGHING AT HIM.
INTRODUCTION
Bifrost 2/64 is our most affordable, hardware-balanced, True MultibitTM DAC. With 4 stereos multibit D/A converters, time- and frequency-domain optimized digital filter, NOS mode, Unison USBTM input, and an all-new AutonomyTM platform for easy firmware and hardware upgradability in the future, we think you’ll agree: Bifrost 2/64 is a stunning DAC.
WHAT’S IN THE BOX
(1) Bifrost 2/64
(1) Remote Control
(1) Power cord
(128) Bits total
**** The following is required by the roughly 9,542 government agencies and regulations we have to comply with. If you have some common sense, they should seem pretty straightforward. In any case, read these instructions before proceeding further, follow all instructions, and heed all warnings. Or else!
- If you don’t know how to install audio devices, get a qualified professional to help.
- Never use this device near water, and clean only with a dry cloth.
- Assure adequate ventilation, do not block any ventilation openings or place them near heat sources.
- Use only the supplied power cord or a suitable replacement. Route cords away from traffic areas and protect them from being pinched. Unplug the cord from the outlet if the apparatus is unused for a long period of time.
- To prevent electric shock, do not use the plug with an extension cord, receptacle, or outlet unless the blades can be fully inserted.
- Refer all servicing to qualified service personnel. Service is required when the device has been damaged, including cord or plug damage, liquid has been spilled or objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE TO RAIN OR MOISTURE.
GETTING STARTED
- Connect Bifrost 2/64 to your source and your amp or preamp. You’ll need RCA-to-RCA or XLR-to-XLR cables to connect the Bifrost to your preamp or amp, as well as a digital cable or cables (coaxial, Toslink, or USB) to connect your source or sources.
- If you are using a USB, use a good, short cable. You need to use a 2M or less, true USB 2.0 rated cable at a minimum. The one you found covered in dust at the back of the closet may not cut it, but any new USB cable from a reputable cable manufacturer should do just fine.
- If you are using a computer source, ensure it is set to output to the Bifrost. Sometimes PCs and Macs get confused and want to use internal speakers, or your powered USB headset, or whatever.
- Select your source using the button on the front panel. And enjoy your music!
ABOUT DRIVERS
Schiit’s Unison USBTM is UAC2 compliant, which means it does not need drivers
on any modern operating system.
ABOUT UPGRADES
Bifrost 2 is firmware upgradable via a MicroSD card slot, and hardware
upgradable via slide-in Input Card and Analog Cards.
Firmware upgrades, when available, will be posted at schiit.com/firmware,
together with information on how to write to a microSD card.
Hardware upgrades, when available, will be purchasable on the Schiit site, in
the Upgrades section. These upgrades simply slide into the appropriate slot on
the back panel, so you won’t need to send it in for an upgrade.
If you’d like to be the first to know about upgrades as they become available,
sign up on the SPAM link on our site.
FRONT CONTROLS
-
Input Select. Press the button to cycle through Coaxial, Optical, and USB inputs. Press and hold to go into NOS (non-oversampled) mode. The input LED will slowly pulse when in NOS mode.
-
Input LEDs. From left to right, this indicates the USB, optical, and coaxial inputs.
Note: The input light will flash if Bifrost 2 is muted. You can mute and unmute via the remote control. -
Remote Window. The remote control communicates through this window. 4 Invert LED. When the output is inverted, this LED will light. You can invert and de-invert via the remote only.
REMOTE CONTROL
The remote allows you to cycle through inputs, mute the output, and invert
the output.
Changing the Battery
- Push the remote open by inserting the end of an open paper clip into the hole in the back and pressing firmly.
- Replace the battery inside with one of the same types.
- Reassemble the remote by first inserting the clear LED in the front, then dropping the panel down onto the matching magnets.
REAR CONNECTIONS
-
XLR Outputs. Connect to your preamp or amp with XLR cables.
-
RCA Outputs. Connect to your preamp or amp with RCA cables.
Note: Both RCA and XLR outputs are active at the same time. -
Firmware Update Slot. Follow the directions at schiit.com/firmware to create a microSD card to insert here when it’s time to upgrade firmware. NO IT WILL NOT PLAY YOUR MUSIC FILES.
-
Coaxial Input. Connect to a digital source with coaxial output using a coaxial cable.
-
Optical Input. Connect to a digital source with Toslink output using a Toslink cable.
-
USB Input. Connect to a computer or streamer using a minimum USB 2.0-rated cable, 2M or less in length.
-
Power Switch. Up for music, down for silence. You get the picture.
-
Power Inlet. Connect the power cord here, or #7 won’t work. Don’t connect a 115VAC Bifrost to a 230V power source, or you’ll blow the fuse.
FAQ
I hear him from Bifrost 2/64. What do I do?****
– Bifrost’s noise floor is insanely low, so it’s most likely a ground loop. To
fix a ground loop, try a HumX or a ground loop isolator.
– Hey, this thing clicks between songs/between inputs/etc! Yes, it does.
Care to explain why smartass?****
– Sure. That’s the muting relay engaging when there’s no input. We went with a
muting relay because it’s the best way to ensure there are no clicks or pops
when the input is unlocked.
– The input LED is slowly fading in and out. That means that Bifrost is in NOS
(non-oversampled) mode. Press and hold the input button for 2 seconds, then
release it to go into standard mode.
I have a version of Windows earlier than Windows 10, where do I get drivers?****
– We do not provide drivers for earlier versions of Windows. All modern operating systems support our UAC2 compliant input without drivers.
What happens if I plug a random microSD card in the firmware upgrade slot?****
– You’ll get flashing LEDs that mean the card isn’t recognized. You won’t hurt the DAC. Nor will you hear beautiful music from your FLAC files, unlock a secret function to align the electrons in your cables, or make any significant change whatsoever. Just use it for firmware upgrades when they are available at schiit.com/firmware.
I don’t get any sound from Bifrost! Are your sources on?****
– Check those first. If you’re using a computer source, ensure that your computer’s sound output is set to go to Unison USB in BOTH your Control Panel/System Prefs AND your player software.
Can I leave Bifrost on all the time?****
– Sure, if you want to. It won’t hurt anything.
It doesn’t turn on, what do I do?****
– Plug it into a different AC socket. Ensure you are not currently in a blackout. Then email us if it still doesn’t turn on.
5-YEAR LIMITED WARRANTY
Schiit Audio warrants to the original purchaser that this product shall be
free from defects in material and workmanship for five (5) years from the date
of purchase. If a defect covered by this warranty occurs during this period,
Schiit Audio will repair the defective product, free of charge. The date of
purchase will be based on customer receipts, otherwise, date of manufacturing
will be used.
If you believe you need warranty service, contact us first. Schiit Audio
products sent back to us without a Return Authorization (RA) will be returned
to the sender without repair. To contact us and obtain an RA, email
info@schiit.com.
Warranty Limitations. This warranty shall not apply if a product: (a) is
modified or tampered with; (b) is damaged by negligence, accident,
unreasonable use, or other causes unrelated to defective materials or
workmanship, or (c) has had the serial number altered or removed.
Any implied warranties, including warranties of merchantability and fitness
for a particular purpose, are hereby limited in duration to the warranty
period of 2 years. In no event shall Schiit Audio be liable for consequential
or incidental damages resulting from the breach of any implied or expressed
warranties. Some states do not allow these limitations, so they may not apply
to you. You may also have other rights which vary from state to state or
province to province.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment under FCC rules.
This product is in compliance with the standards and regulations of the
European Community.