DIGITAL WATCHDOG DWC-V6563WTIR Star-Light 5MP Outdoor Universal Dome Camera User Guide

DWC-V6563WTIR Star-Light 5MP Outdoor Universal Dome Camera
User Guide

WHAT’S IN THE BOX

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the ‘Search by Product’ search bar. Results for applicable part numbers will populate automatically based on the part  number you enter.
3. Click ‘Search’. All supported materials, including manuals and quick start guide (QSGs) will appear in the results.

http://bit.ly/resources_qr

Attention: This document is intended to serve as a quick reference for initial set-up. It is recommended that the user read the entire instruction manual for complete and  proper installation and usage.

STEP 1 – PREPARING TO MOUNT THE CAMERA

1. The mounting surface must withstand five times the weight of your camera.

2. Do not let the cables get caught in improper places or the electric line cover can be damaged. This may cause a short or fire.

3. Install the moisture packet in the base of the camera’s lens.
   a. Remove the moisture absorber from the packaging.
   b. Cut the card and folder along the dotted line.
   c. Place the moisture absorber behind the camera’s lens module. See drawing for more information.
   *Please cut the card type absorber along a dotted line, overlap and attach them according to the direction of the arrow. NOTE: The camera will generate enough heat to dry moisture during operation. In most cases it will not need the moisture absorber for more than the first day. In cases where the camera can experience a moisture issue, users must keep the moisture absorber in the camera.
   The moisture absorber has an approximately 6-month life cycle, varying depending on the environment. WARNING: It is highly recommended that you install the moisture absorber when mounting the camera. The moisture absorber prevents moisture from being captured inside the camera’s housing, which may cause image performance issues and damage the camera.

4. This product is intended to be supplied by a UL Listed Power Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.50A min. or 24 Vac, 50/60Hz 0.36A min.

5. Remove the dome protection film before placing the dome back on the camera base.

6. Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.

STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES

Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.

DC12V (LED on): 5.9W (495mA)
AC24V (LED off): 2.75W (200mA)
AC24V (LED on): 5.3W  (360mA)

STEP 3 – CHANGING THE SIGNAL IN THE CAMERA

1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To switch between the signals:
   a. Enter the camera’s OSD menu. You can access it locally from using the camera’s joystick in the body of the camera, or from a recorder supporting UTC communication. Go to SETUP > OUTPUT > ANALOG MODE.
   b. Set the camera’s analog signal output from the following options:
   • HD-A: supports 5MP/1944p @ 20fps 4MP/1440p @ 30fps, 2.1MP/1080p @ 30fps and 720p @ 30fps.
   • HD-T: supports 5MP/1944p @ 20fps, 4MP/1440p @ 30fps, 2.1MP/1080p @ 30fps and 720p @ 30fps.
   • HD-C: supports 4MP/1440p @ 30fps, 2.1MP/1080p @ 30fps and 720p @ 30fps.
   • CVBS: supports up to 960H @ 30fps
   c. Change CONFIRM to ON to save the changes.
   d. Go to the EXIT menu and select SAVE&EXIT to save all changes.
   The camera signal automatically.

NOTE: To use your Star-Light Plus™ 5MP cameras at a lower resolution, you must use a VMAX® A1 Plus™ DVR to access the camera’s menu due to the cameras being  set to 5MP as the default. A DVR that does not support 5MP resolution may recognize the camera, but will not deliver a picture

STEP 4 – INSTALLING THE CAMERA

1. Once all cables have been connected, use the screws included with the camera to properly mount and secure the camera to the mounting surface.

2. Adjust the camera’s pan, tilt and position to achieve the desired view.
   The cameras’ max angles are:
   Pan: 0° ~ 360°
   Tilt: 0° ~ 90°
   Rotation: 0° ~ 360°

3.  To adjust the camera’s focus and zoom:
   a. Unlock the zoom or focus screws by rotating them counter-clockwise.
   b. Adjust the zoom and focus screws at the base of the camera module to achieve a clear image.
   c. Tighten the screws and close the front case by rotating it clockwise.

4. Once the installation is complete, remove the protective film from the camera’s dome cover.
   

Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>