DIGITAL WATCHDOG DWC-V7253WTIR DW Universal HD Over Coax Ultra Low-Profile Vandal Dome Cameras User Guide

Quick Start Guide
DW® Universal HD over Coax®
ultra low-profile vandal dome cameras
DWC-V7253WTIR

WHAT’S IN THE BOX

NOTE: Download all your support materials and tools in one place.

1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the ‘Search by Product’ search bar. Results for applicable part numbers will populate automatically based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals and quick start guide (QSGs) will appear in the results.

http://bit.ly/resources_qr

Attention: This document is intended to serve as a quick reference for initial setup. It is recommended that the user read the entire instruction manual for complete and proper installation and usage.

STEP 1 – PREPARING TO MOUNT THE CAMERA

1. The mounting surface must withstand five times the weight of your camera.
2. Pay attention to the cables. The can easily become caught and damaged. Any damage may cause a short or fire.
3. Detach the camera’s dome cover by loosening the 2 screws on the dome using the included torque wrench.
4. This product is intended to be supplied by a UL Listed Power Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.24A min.

STEP 2 – CABLING THE CAMERA TO

EXTERNAL DEVICES
Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.

12VDC ONLY!
CAUTION! The camera supports
DC power supply only| DC12V(LED off): 1.7W
DC12V(LED on): 2.9W

STEP 3 – CHANGING THE SIGNAL IN THE CAMERA

1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To switch between the signals:
   a. Remove the camera’s dome to access the joystick and OSD control on the base of the camera.
   b. Use the OSD Switch to switch the camera’s signal.
   – To switch the camera to HD-TVI mode, press OSD joystick to the left for 5 seconds.
   – To switch the camera to HD-Analog mode, press OSD joystick to the right for 5 seconds.
   – To switch the camera to CVBS mode, press OSD joystick up for 5 seconds.
   – To switch the camera to HD- CVI mode, press OSD joystick down for 5 seconds.

STEP 4 – INSTALLING THE CAMERA

1. Once all cables have been connected, use the screws included with the camera to properly mount and secure the camera to the mounting surface.

2. Adjust the camera’s pan, tilt and position to achieve the desired view.
   The cameras’ max angles are:
   Pan: 0° ~ 360°
   Tilt: 0° ~ 70°
   Rotation: 0° ~ 360°

3. Once the installation is complete, remove the protective film from the camera’s dome cover.

4. The camera has a manual IR switch, located under the camera’s lens. You can use this switch to manually turn the IR LED board on or off according to the installation needs.

For a bolt and nut installation:

1. Using the bolt and nut mounting template, mark and drill the necessary holes in the mounting surface.
2. Pass wires through and make all connections (see STEP 2 for more information).
3. Secure the two long mounting screws to the camera’s base.
4. Mount the camera to the mounting surface by using the 2 mounting nuts.
5. Rotate the locking discs over the screws until the camera is held tightly from the mounting surface.

Copyright © Digital Watchdog. All rights reserved.
Rev Date: 02/22
Specifications and pricing are subject to change without notice.
Tel: +1 866-446-3595 / 813-888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>